Latest train display board Tenders | Government train display board Tenders

CTN :44358510

02 Jul, 2026 NA

Kannur - Kerala

Tender For bid to ras procurement of trainer kits / equipment for advanced electronics laboratory - 741 op-amp trainer kit , programmble function generators 25mhz , true rms digital multimeter6 , 100mhz digital stroge oscilloscope

CTN :45720488

07 Jul, 2026 NA

Tiruvannamalai - Tamil Nadu

Tender For procurement of mech. lab equipments - single phase ac circuit kit for voltage,current and power measurement, mcb elcb trainer kit, single phase induction motor kit for load test by speed control of vfd (variable frequency drive), dc shunt motor kit for load test, stepper motor drive kit, servo motor drive kit, bldc motor kit, digital trainer kit(ic7400,ic7402.ic7404,ic7408,ic7432,ic7486,ic74186, magnetic yoke

CTN :45726000

06 Jul, 2026 NA

Tiruvettipuram - Tamil Nadu

Tender For procurement of digital ic trainer kit for computer engineering department.

State Government

CTN :45709910

27 Jul, 2026 NA

Rourkela - Odisha

Tender For supply and installation of equipments for electrical measurement and instrumentation laboratory of electrical engineering department - wheatstone bridge , trainer kit , maxwell inductance bridge trainer kit , de-sauty's trainer kit bridge , kelvin's double bridge trainer kit , schering bridge trainer kit , anderson bridge , trainer kit , lvdt , characteristics , hay's bridge trainer kit , j-type thermocouple characteristics trainer , 2 channel digital , storage , oscilloscope , 25 mhz , dual- , channel arbitrary , function generator , hand held digital multimeter

CTN :45703554

17 Jul, 2026 NA

Kamrup - Assam

Tender For supply of basic electronics lab equipment & software - zener diode voltage regulator trainer kit , digital oscilloscope , multiple dc power supply , transistor characteristics trainer kit , kirchhoff’s current and voltage law trainer kit , active filters trainer kit , multiplexer and demultiplexer trainer kit , 10mhz function/arbitrary waveform generato , bidder must provide 10 days onsite training & installation of the equipment & software for trtc, guwahati officials at trtc, guwahati

CTN :45693900

10 Jul, 2026 NA

Mumbai - Maharashtra

Tender For supply and installation of automobile trainers and equipment at consignee locations. (tender ref no.26008/2026-27) - light motor vehicle driving simulator, injector -multi hole type, pintle type, petrol engine - 2 stroke, motor cycle/ scooter, injector cleaning unit, injector testing set (hand tester), fuel feed pump for diesel, fuel injection pump - diesel - inline, fuel injection pump - dismantling tool kit, fuel injection pump - distributor fuel rotary pump with standard accessories, fuel injection pump - ve pump with standard accessories, cylinder liner- dry & wet liner, cylinder liner - press fit & slide fit, steering assembly - rack and pinion, air brake trainer assembly, alternator assembly - lmv, engine bearing model set, piston model set, front axle assembly, rzeeppa joint with stand for dismantling and assembly, full floating axle and semi floating axle assembly, wiper motor assembly, cut section model - 4 cylinder diesel engine, cut section model - automatic transmission gear box, cut section model - centrifugal clutch assembly, cut section model - diaphragm clutch assembly, cut section model - radiator - cross flow, cut section model - radiator - down flow, cut section model - shock absorbers, cut section model - single plate clutch assembly, cut section model - turbocharger, demonstration board - anti theft device car, automotive safety air bag simulator, car air conditioner trainer, demonstration board - crdi system, demonstration board - electronic ignition system and ignition coil, disk brake trainer, drum brake trainer, working model - power windows, working model - torque converter, denting kit set, engine compression tester (diesel), two post car lift- capacity 4 ton, electric operated, radiator pressure tester, tyre changer machine, tyre air pressure gauge with holding nipple, wheel alignment machince computerized 3d, wheel balancing machine (for wheel balancing of lmv), air conditioning service unit - car, automotive battery charger, automotive battery tester/ analyser, battery terminal cleaner tool, air blow gun, air impact wrench with impact sockets, engineers stethoscope, grease gun - 500 grams, oil can 500 ml, oil filter wrench - upto 500 mm, piston ring compressor - 50 - 100 mm, piston ring expander and remover - 50 - 100 mm, piston ring groove cleaner, belt tensioner gauge, car jet washer with standard accessories, auto electrical work bench, gloves: rubber, gloves: cotton, industrial/ safety shoes, industrial helmet, blow lamp: 0.5 liter, magnifying glass: 75 mm, lifting tackle/ sling: 1 ton, 2 meters, laser distance measuring instrument, demonstration board: electric vehicle cooling system, engine and transmission system for electric vehicle, cut section of electric vehicle motors, hvac trainer, electric vehicle service equipment test adapter kit, battery tester with inbuilt printer, lighting and wiring system for electric vehicle, electric vehicle diagnostic scanner, solar based charging system, electric vehicle tool kit, electrically insulating blanket, clamps for insulating blanket, insulated rubber mats, gloves: electrically insulated, industrial/ safety shoes: electrically insulated, glove inflator kit, goggle: white glass, ac current digital clamp meter, digital continuity tester, soldering iron set: mechanic electric vehicle

CTN :45693976

17 Jul, 2026 NA

Mumbai - Maharashtra

Tender For supply and installation of training items for drone technician trade under craftsman training scheme (cts) at consignee locations - pliers, soldering station, multi meter, binoculars, anemometer, magnifier, unassembled drone kit, unassembled drone kit - standard with hd camera & thermal camera, electricity lab, smd technology kit with wall chart, dc regulated variable programmable dc power supply, drone workbench, analog-digital circuits development platform, applied mechanics training platform, drone battery management training systems, charge controller training system, bldc (brushless dc) motor training system, inverted pendulum, drone sensor trainer kit, antenna training system, advanced microwave integrated circuit lab, gps training platform, wireless communication modules, fcb and esc training platform, drone gimbal set with motor and control, npnt compliant micro uav built for mapping and surveillance, field repair kits, drones and spare parts kit, balance charger, power distribution board, laptop latest configuration, thrust measurement meter, indoor netted facility, outdoor controlled netted testing facility, various electronic and electrical components, 3d printer, drone ( long range)

CTN :45705420

17 Jul, 2026 25.0 Thousand

Vyara - Gujarat

Tender For supply of digital trainer kit (q3)

CTN :45696133

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

Central Government/Public Sector

CTN :45702760

03 Jul, 2026 NA

Multi City - Tamil Nadu

Tender For auction sale of depot ferrous scrap - cond. and u/s ferrous fabricated materials of ms/ci scrap in nature such as weld mesh, ms duct, anti slip arrangement, earthen bond, galvanized (gi) sheet, ms sheet of various sorts and sizes, blower rotary forging, liner, guide fixtures, side frame fixtures, trolley of various sorts and sizes, trolley wheel & frame, battery fixing iron tray, ms pipe, coach/wagon stand, conveyor belt, ferrous body of auto change over panel, wire mesh, emu coach cut parts, ferrous portion of cab window assembly, sign on iron stand,castiron tems,girder base with concrete adhearings,gearset,grill,vcb panel boxes,gipipes,nuts and bolts,angles,rails,panel boxes,fissureplates,wheels,cupboard, structural items, different type of packing channels, trolley, lat, coach cut up parts, head stock, ms tank, grill gate, rolling shutter,wheel with plate, bins,regulator empty box, dolley, fob fencing, corrugated sheets, rectangular square tube &galvanised sheets, bogie mounted brake beam,brake blocks, gi sheets, pipe,square &rectangular tubes,stair case and handle,ferrous body of various types of motor, angle and channel fabricated with nut, bolt with or without brick and concrete,ladder,plate,grill, barricade, bolts, nuts, tray under frame, cut rod, rails of various sorts and sizes with/without concrete/brick/mud adhering,cut rails or rails used in support structures, coach head stock, coach parts,battery tray, ladder, all types of trolley wheels with minor nfs attachments, screens, channel post, sheets, stand, track machine cut up parts, ms pipes covered with or without rope &with or without parts of rubber, dome, vrla rack, vcb in dismantled condition, vrla battery box & clamp, stand, dtmf way station equipment box, led line display board, hydraulic lifting table with available fittings, vrla battery empty container, bed/base plate, fabricated cut rods,gi pipes, ci pipes and fittings, ms plate, roofsheets, angle, plate, platform bench, spring plank, clamps, cabinet, ms grill, sheets, ladder, steel gate, trolley,ms water tank, fire tender tank,roof truss supporting columns,purlins, sand box, fencing, tl rod, vcb panel, train display board, battery stand, boards, tools box, empty regulator &empty battery container, cut rod, ticket punching cut parts, hand rail, fabricated post/pipe/rod, strips, hoods, impellor, base plates, meshes, battery box frame, grs box, control panel, fan down rod, ac window covers ,angle / channels with/without rails, angle of tld, rack, lt panels, ferrous electrical panel boxes,i beam,transmission rods,fissure plates, main switch panel board w/o nfs attachments, ebc & rbc frame &enclosure,emu sliding door, high beam, silencer, , garden light post, tap changer cover with fiber attachments, empty battery container, stretcher, cupboard, dust bin, iron step, empty rotary junction box, empty regulator box, iron metal box, air reserviour compressor cylinder of varous sorts & sizes, garden light post, stand, mdb w/o non ferrous attachments, st light tubular post, gi/ms window, luggage rack, ,bed portion of weighing scale l with or without any minor non-ferrous attachments and all other scrap excluding ms hand hold in fabricated nature of sorts and sizes full/broken with/without other fs/ci/gi fittings in as is where is condition.pl no 98050126. note:(1) cutting is permitted to loadable size and for heavy nature items only. 2) during delivery if any major non-ferrous items found the same may be handed over to custodian. 3) jcb/crane loading permitted. location: (1)behind a row bin 3&4, (2)near old e-ii ward annexe

Train Display Board Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector