Latest trunion shaft Tenders | Government trunion shaft Tenders

Central Government/Public Sector

CTN :45512258

22 Jun, 2026 NA

Bardhaman - West Bengal

Tender For 213178432 screw shaft , 213458255 guide roller , 213458266 guide roller , 213458428 dial , 213458429 650 mm mill dial , 213458430 650 mm mill dial , 213458533 guide box , 213458607 button , 213458608 button , 213468307 eccentric shaft

CTN :45516800

26 Jun, 2026 3.50 Lacs

Farrukhabad - Uttar Pradesh

Tender For tender for reshelling of under feed roller shaft with scrap of mill size 30 inch x 60 inch mill 530 mm x 1520 mm as per drawing no m 64 b , grooving charges of roller pitch size 25 mm , grooving charges of roller pitch size 50 mm , journal polishing of roller shaft , dummy1

State Government

CTN :45317543

15 Jun, 2026 NA

Multi City - Telangana

Tender For corrigendum : tggenco-ytps-supply of gravimetric feeder spares for hp1103 bowl mill in boiler -ii division. - calibration roller complete assembly, bearing housing,inlet spanroller, bearing housing,weigh spanroller, bearing housing, calibration roller, grease sealfor belt takeup pulley for inlet, weigh span roller grease seal for inlet, grease seal for calibrating for inlet, tension roll grease seal for inlet, wear sleeve belt take up for inlet, tension roll wear sleeve for inlet, drag ling assembly for inlet, bolt for drag ling, bolt for belt takeup rail support for inlet, weigh span roller pre loading washer for inlet, bolt forweigh module, tension roll pivot bolt for inlet, bearing housing-ii for weigh span rollers, retainer ring for calio shaftfor inlet, weigh span roller retainini ring for inlet, tension roll retainer ring for inlet, inlet span roller retainer ring for inlet, weigh span roller hanger rod, ring,retaining, block belt takeup for inlet, belt takeup pulley assy shaft for inlet, inlet skirt (rh) for inlet, inlet skirt (lh), end skirt for inlet, levelling bar for inlet, head pulley wear sleeve, bulls eye glass for inlet, shear pin for coc shaft, coal on belt padoie for inlet, coal on belt grease seal for inlet, oil seal, 70x85x8 mm, counter weight,of weighsensing system

Co-operative

CTN :45474707

23 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For c.i. item on conversion/supply basis - c.i.pipe with standard thickness & flange as per i.s.i. specification machined from dia 4" to 12"(i) new material supply basis, (ii) on conversion basis, c.i. bend, duck foot bend, cross,tee and other such part all size as per drg.(i) new material supply basis, (ii) on conversion basis, c.i.drum, rod,bush, bari,idler pully, break drum for cane unloader etc as per drg.(i) new material supply basis, (ii) on conversion basis, c.i.coupling from 4"dia to 10"dia plane/flange type(i) new material supply basis, (ii) on conversion basis, c.i. firing frame,door side chamber, bagasse rotary chuts, rotary feeder drum , clit, hanger, beam, gutka, furnace nozzle, clam etc. and other such parts for lipi/taxmaco boiler as per different drg.high chrome grade 25 , casting & machined temp. capacity 15000 c(i) new material supply basis, (ii) on conversion basis, c.i. clamp/ hanger clit small size for lippi boiler no. 3 as per drg. blr-79 high chrome grade 25 , casting & machined temp. capacity 15000 c, c.i scapper mixed with pig iron and having standard hardness dully machined as per drg.no.mh-66 ( r)(i) new material supply basis, (ii) on conversion basis, (iii) grooving of c.i.scrapper as per drg., centrifused casted c.i.coupling for fmg gear of kcp mill od 1000 mm.pcd 815(18 holes)9+9,with machining complete as per drg.no.mh-93, c.i.motor cover for different type motor, mill setting bolt & nut for kcp mill drg.no.mh-106, mill setting bolt & nut for taxmaco mill drg.no.mh-38, c.i.worm and worm wheel for crystilizer as per drg.bh-39 ( r ) machined, c.i.worm and worm wheel for vertical crystilizer no. 2 complete set as per drg. machined, eccentric shaft and eccentric for hopper as per drg.no.bh-60, m.s.shell for under feed roller as per drg.mh-95.length 1525 mm.od 750mm,thickness 18mm, c.i. muff coupling for cane unloader as per drg.no cu-25, c.i.gear for magma mixture as per drg.no bh-137.od 450mm,no.of teeth-51.bore 70mm, width 63mm, c.i.brake drum for s.d.centrifugal machine taxmaco make duly machined(i) as per drg.no. bh 81/1, (ii) as per drg.no bh-81/2, c.i.v-belt pully of cont.centrifugal machine duly machined, c.i.scale seat for juice weighing scale duly machined and drilled as per drg.no.mh-195, id fan pully (as per drawing no. bl-r-128/2024-25), id fan motor pully (as per drawing no. bl-r-129/2024-25), boiler grate bar material-cont iron. (as per sample/drg.), boiler furnace manage gap bar. (ap per sample/drg.), chief engineer

corporations/Associations/Others

CTN :45468516

22 Jun, 2026 28.12 Lacs

Sonbhadra - Uttar Pradesh

Tender For supply of split oil sea l , split oil seal dust guard for mech , o ring oil seal v15 , oil seal modified , wear sleave jr shaft , o ring for pressure spring , split oil seal , split oil seal dust guard viton , oil seal modi u j hsg , trunion shaft bushing sty 02 , oil seal sl no 6 , oil seal 40x52x7 , oil seal 55x75x9 , oil seal 75x95x13 nitrile rubber , oil seal 16x28x7

Corporations And Associations And Others

CTN :45444916

22 Jun, 2026 NA

Jalandhar - Punjab

Tender For mill roller shaft make bharat forge - supply of mill roller shaft (make bharat forge)

Co-operative

CTN :45415201

10 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For fabrication and erection -replacement of the 2" x 2" square bar rails installed on the cane unloader. removal of the old juice gutter from 'a' mill, fabrication and installation of a new one, and conducting a successful trial run. removal of the old m.s. juice tray from 'a' mill, and fabrication and installation of a new one using m.s. plates. fabrication and installation of a new gear guard in the 'a' mill house. welding of worn-out teeth on the mill pinion as required, followed by grinding to a smooth finish. repair of damaged/worn parts of the tail bar coupling by welding as required, followed by grinding. repair of damaged/worn parts of the tail bar by welding as required, followed by grinding. comprehensive repair of the d.s.m. screen: cutting out and removing corroded sections, fabricating and fitting new replacements, repairing all internal piping, and conducting a successful trial run. thorough cleaning of the cane carrier slats, along with their attached links, pins, rollers, and bushes; followed by greasing and refitting said components into the slats in their proper positions. thorough cleaning of the slats, links, pins, bushes, and rollers of the primary/secondary cane carrier chains; followed by greasing, assembling the chain components, and preparing the chain as per instructions. fabrication and installation of juice rings for the rollers. fabrication and installation of mill bearing guards using 3 mm plates. fabrication and installation of m.s. scrapers for the under-feed rollers. cutting of chevron grooves into old mill rollers as required. cutting of chevron grooves into new mill rollers as required. creating 'dots' on the top and feed rollers of the mill using arc-welding electrodes, as per instructions. [repair/replacement of] m.s. components for the worn-out teeth of the under-feed rollers. cutting out patches from a plate and installing them as new teeth. performing arc welding on the grooves of rollers used in the mills using electrodes, as per instructions. fabricating side juice guards for mill rollers from 3 mm plates, as per instructions. fabricating an under-feed roller for the mill in accordance with the provided drawings. dismantling a damaged or defective juice tank in the mill house; fabricating and installing a new tank in its place, and conducting a trial run. replacing or repairing the damaged sections of a defective juice tank in the mill house. dismantling and replacing the bottom plate of a damaged or defective juice tank in the mill house. cane carrier / bagasse carrier / bagasse elevator / cross bagasse carrier / r.b. c. removal of the cane carrier side plate and installation of a new plate. a. welding or forging the enlarged pin holes in the links of the cane carrier, bagasse carrier, etc., to match the specific pin size. a. removal of broken runners from the cane carrier, inter-carrier, bagasse elevator, return bagasse carrier, or cross bagasse carrier, and installation of new runners in their place. a. removal of old, damaged cane carrier slats and installation of new slats. a. the task of drilling holes in new slats for the cane carrier and inter-carrier. a. straightening and repairing cane carrier slats as required. a. repairing damaged and weakened hoods of the cane chopper, cutter, and fibrizer in accordance with instructions. a. removal of old, damaged cane carrier slats; straightening the damaged slats; cutting out the damaged sections; and repairing them by welding in new or salvaged slat pieces cut to size, thereby restoring the slats to their proper dimensions. a. welding the enlarged holes in the inter-carrier links and re-drilling them to the correct size to match the rivets. a. filling the enlarged holes in old inter-carrier slats by welding, and subsequently re-drilling them to create new holes in accordance with the engineering drawings. a. removal of the damaged band from the inter-carrier clutch shaft, fabricating and installing a new one, and conducting a satisfactory

State Government

CTN :45402026

23 Jun, 2026 NA

Yamunanagar - Haryana

Tender For supply of coal mill feeder spares - vieweing mirror with whiper (as per sample) , belt tension roller moc: (en-8, forged alloy steel) (as per sample) , seal housing moc: carbon steel 1030 grade (as per sample , head pulley/driving pulley moc: carbon steel (as per sample) , take up pulley with eccentric bearing housing moc: carbon steel , support roller of r/c feeder moc: carbon steel; shaft material en-8 (as per sample) , take up shaft (moc: en8) as per sample ,, bearing housing of connecting plate of head cell of r/c feeder/ moc- aluminium (as per sample) , connecting bushing (with pin) 1 set =10 nos. moc: neoprine rubber with bronz bush (as per sample)

State Government

CTN :45147318

09 Jun, 2026 40.52 Lacs

Jharsuguda - Odisha

Tender For corrigendum : supply of deflector side liner leading mill hp1103 , deflector liner lower,sl-15 mill hp1103 , deflector liner lower,sl-20 mill hp1103 , deflector liner mid,sl-25 mill hp1103 , deflector liner mid,sl-30 mill hp1103 , intermediate liner leading mill hp1103 , intermediate liner trailing mill hp1103 , ceramic plug for deflector liner hp1103 , welding plug for deflector liner hp1103 , air restriction ring segment , deflector liner mid,sl-35 mill hp1103 , seal wear ring for journal mill hp1103 , head liner- 4 for head liner assembly , head liner-2 for head liner assembly , head liner-6 for head liner assembly , trunion shaft bushing for coal mill hp1103

State Government

CTN :45190306

22 Jun, 2026 17.12 Lacs

East Nimar - Madhya Pradesh

Tender For corrigendum : procurement of consumable spare parts of journal head and trunion shaft of bhel make xrp-1063 coal mills installed at 2x600mw, sstpp, mppgcl, dongalia.

Trunion Shaft Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors