Tender For auction sale of depot ferrous scrap - scrap ms melting consisting of buffer plunger with or without spindle, buffer socket, drake beam and truss bar, nut- bolt, rivets, pin, bush, small die, inner race, outer race, suspention strip, washer, door hinges, door roster, ff or rf, hb wheel, side bearer plate, yoke plate,, bottom plate, sbs plate, anchor plate. hb lever, be lever, bc link, empty axle box, axle box cover, axle box housing, foot step, briddle bar, striker casting, back stopper, empty load box, main hole cover, shackle, shackle pin, screw cupling, bearing long shaft, cbc parts of coaches with undetchable nylon bush and other nylon items, shackle stone, coil spring, locking plate, shaft, operating handle, draw bar, broken coil spring up to four coil, front and rear plate, vertical support assly, main pin of cbc shank, manual uncoupling handle, wedge lock cbc parts of coaches, vertical supporting device for cbc, anti roll bar of lhb coaches, plunger, foot step, bb hanger, eq lever, bk shoe, striker casting, brake shoe head, bk.shoe key, sielent block yoke pin support plate, lashing chain, buckle, roller backing ring, spacer, distance ring, cone assly and other parts of ctrb wire supporting hook, prptecting tube, silent block all type, l.s. beam, knuckle pin, knuckle plate, front and back cover of door cylinder clamp, bearing pieces, silent block all type, sab complete and sab loose part, sab rod, and all type rod released from wagons loose and attached, control rod.coupler rod, roller, cone, backing ring, spacer, distence ringsmall cut pieces of s.s., bracket, upper and lower part of control arm of lhb coaches and other ferrous melting category items, with or without minor undetachable non-ferrous attachment. [qty on approx basis). as per e-auction terms and condition goverining sale of scrap material through e-auction (revised on 07.05.2026), delivery of any scrap lot shall be permitted only after receipt of full sale value of sold lot.
Tender For supply of cbc (aar-h type) measuring gauge. a complete set of gauges is consist of following six gauges forinspection and measurement of cbc h type (aar-h type ) coupler . all gauges are made of hard alloy steel andhardness 45-50 hrc with nickel plating & laser marking. 1. contour condemning limit gauge (jaw gap gauge) forchecking cbc h type coupler to aptp drawing /gauge no-34100-1- 01 no. 2. contour maintenance gauge (knuckleprofile gauge) for checking cbc h type coupler to apta drawing gauge no. 31000 -01 no. 3.aligning wing limitgauge for checking cbc h type coupler to apta drawing/gauge no- 32600 -01 nos. 4- knuckle nose wear &stretch limit gauge for checking cbc h type coupler to apta drawing/ gauge no- 34100-2a-01 no. 5- verticalheight aligning wing pocket & guard arm gauge (go gauge must pass) for checking cbc h type coupler to aptadrawing/gauge no. 34101-4 -01no. 6- vertical height condemning limit aligning wing pocket & guard arm gauge(no. go gauge must not pass) for checking cbc h type coupler to apta drawing/gauge no.- 44250-5-01 no. makepie/ganapathy/ or similar [ warranty period: 30months after the date of delivery ] ]
Tender For supply of set of cbc gauges .one set consist of 06 gauges for checking of aar h type centre buffer coupler of lhb coaches. gauges made of hard steel alloy or stainless steel with hardness 45-50 hrc as per attached specifications (i) contour maintenance gauge (knuckle profile gauge): apta drawing/gauge no.31000 (ii) aligningwing limit gauge: apta drawing/gauge no. 32600 (iii) contour condemning limit gauge(jaw-gap gauge) aptadrawing/gauge no. 34100-1 (iv) knuckle nose wear and stretch limit gauge: apta drawing/gauge no.341002a (v)vertical height aligning wing pocket & guard arm gauge (go gauge-must pass): apta drawing/gauge no.34101-4(vi)vertical height condemning limit aligning wing pocket & guard arm gauge (no-go gauge-must not pass): aptadrawing/gauge no.44250- 5. [ warranty period: 30 months after the date of delivery ] ]
Tender For supply of knuckle bearing , knuckle bush , wiper blade , combination switch , brake booster repair kit , door lock front lh , assembly rear door rh , hood balancer , siren elect , tie rod end , brake pad , tie rod assembly , control panel , upper arm assembly , selector shaft 4x4 , assembly silencer pipe , water pump assembly
Tender For supply of mt spare - 4st relay for stln , self pinion for stln , speedometer cable for stln , fuel pipe for stln , isolator switch for stln , rotary switch for stln , clutch kit for stln , wiper arm with blade for stln , slave cyl kit for stln , relay 24v 40a for stln , relay 24v 80a for stln , relay 12v 40a for stln , relay 24v 70a for stln , ball joint strg for stln , tie rod end for stln , knuckle bearing for stln , self bush for tata 2.5 ton , field coil assy for tata 2.5 ton
Tender For auction sale of others - scrap condemn m. s . material including bss hanger,collar,brake head,d-tube,hook coupling and its parts,draw bar,lower & upper spring support, anti roll bar bracket, buffer face plate,buffer parts,spindle,all type of ms brake lever,equilising stay, oiler ring/earthing plate, m.s. heavy long rod, cylindrical pin, cbc stepnar plate,phonic wheel, security disc, lhb antiroll bar,retaining cap, distance ring , shims packing, anti roll bar m.s. bearing and bush , m.s heavy plate,cbc knuckle, centre buffer coupler and its all parts,control arm & brake disc etc. and like wise heavy ferrous material of icf and lhb coaches, with/without minor teflon/pvc bush/. attachments (approx weight 0.02 %) , ci parts (approx weight 0.1%).old used and unserviceable. mode of delivery in weight. total weight - 100 mt, loading shall be start from bio tank cleaning area without any sorting. bidder may visit the lot before participating. only manual loading will be allowed, custodian - sse scrap bvp, location - : bvp bg workshop at track dead end near incinator as is where is basis, loading by purchaser, fdp 50 days.