Latest tube rota meter Tenders | Government tube rota meter Tenders

State Government

CTN :45613922

03 Jul, 2026 3.58 Lacs

Surat - Gujarat

Tender For providing, supplying and installation with testing demo of additional laboratory equipment for aggregate, cement and mix-design at quality control sub division, rander, dist. surat.- providing and supplying & installation with testing demo of vicat needle apparatus for testing of initial, final seeting time & consistency of cement test. one complete set. confirm to 18:5513 , providing and supplying & installation with testing demo off vicat mould, , providing and supplying & installation with testing demo of vicat glass plate, , providing and supplying & installation with testing demo of le-chatler mould including two glass plates and lead weight as per is set of six., , providing and supplying & installation with testing demo of le-chater flack, , installation with testing demo of slump test apparatus with tamping rod 16 mm dia x 600 mm long graduated., , providing and supplying & installation with testing demo of humidity chamber refrigerated-inner 8.8-45x45x45 cm-92 liter for temperature and humidity control with over temperature protection audio alarm system, , providing and supplying & installation with testing demo of servo voltage stabilizer -3kva-single phase for humidity chamber., , providing and supplying & installation with testing demo of humidifire with controler digital-confirming ito indian standard codes, , providing and supplying & installation with testing demo of whatman fliter paper-40 for blain air permeability test apparatus for fineness of cement, confirming to indian standard codes., , providing and supplying & installation with testing demo of precision electronic balance-600 gmm 01 gm (10mg)-confimming to indian standard codes., , providing and supplying & installation with testing demo of cement morter cube mould-7.06 cm-for cement confirming to indian standard codes (18 10080, 84031), , providing and supplying & installation with testing demo of 90 micron is sleve, , providing and supplying & installation with testing demo of gauging travel 8 anch. (200 mm)-confirming indian standard codes., , providing and supplying & installation with testing demo of temperature meter concrete, , providing and supplying & installation with testing demo of room temperature meter or thermo hygrometer, , providing and supplying & installation with testing demo of tds meter pen type, , providing and supplying & installation with testing demo of ph meter - pen type, , providing and supplying & installation with testing demo of measuring cylinder -borosilicate glass-100ml, , providing and supplying & installation with testing demo of measuring cylinder -borosilicate glass-250ml, , providing and supplying & installation with testing demo of measuring cylinder -borosilicate glass-500ml, , providing and supplying & installation with testing demo of measuring cylinder -borosilicate glass-1000ml, , providing and supplying & installation with testing demo of standard weight box-8.8.-1 mg-200 gm-class f1 (with nabl calibration), , providing and supplying & installation with testing demo of buoyancy balance with electronic balance 10 kg x 0.1 gm, , providing and supplying & installation with testing demo of 1.) distance piece-50mm height-nos 2.) distance piece-30mm, , height-inos, , machine, , providing and supplying & installation with testing, , demo of electronic platform, , balance-100 kg-, , 10 gm platform size 600 x, , , , providing and supplying & installation with testing demo of g.j. tray 1000x 1000 x 50 mm confirming to indian standard codes., , providing and supplying & installation with testing demo of bnd- ordinary portland cement standard specific area (blaine) one set surface, , providing and supplying & installation with testing demo of wash bottle 1000ml, , providing and supplying & installation with demo of spatula testing, , providing and supplying & installation with testing demo of fil

Central Government/Public Sector

CTN :45619737

29 Jun, 2026 NA

Sonpur - Bihar

Tender For auction sale of depot miscellaneousllaneous scrap - dms-scrap-ghz, lot no-342605005, scrap electrical & signaling miscellaneous item like geyser body,stabilizer,cooler body, charger,fuse monitoring system, axle counter, room heater, changer, megger machine, tumble switch, halogen filament, tx-rx coil, mini pantry lhb ac, berth light fitting, ammeter, control transformer, pump controller, emergency light, sphygnomanometer, stethoscope, temperature gun, suction machine, cardiac monitor, deep fridger, nebulizer machine, multimeter projector, vhf charger, insulation tester, iron battery container, tube light, photo state machine, panel body, light cover, led bulb, rru, scroll compressor with or without oil, led signal all type, tube light cover, halogen bulb, fan rod, fan blade, electric energy meter, sound box, tricolor torch, choke, current regulator, multipurpose dry cell battery-1.5v (type r 20), water cooler, refrigerator body, water purifier, elb gear box, starter, earthing device, street light, phase selector, hs meter, flood light fitting, mcb switch, holder off size, fan condenser off size, tf charger, speedometer, transformer body, ac operating panel body, cooler stand, transmitter receiver, tlbi, x-ray machine stand, speaker, oxygen cylinder with flow meter (ss), platform display board, display unit, gate hooter, telephone card, battery charger and other similar type items with or without nf attachment broken, damaged, rusted etc. location-stack a-south side of office garden near over head electric bridge. stack b- south side of office garden about 50 mtr near both side of pakka road. stack c-about 15 mtrs. west of rb section t-point. stack d- east side of ledger section about 40 mtr near kachcha road. stack e- inside old scrap office.

CTN :45620021

10 Jul, 2026 13.82 Lacs

Mussoorie - Uttarakhand

Tender For supply of front loading washing machine 60 kg capacity electric heated automatic time temperature and water level control , hydro extractor 60 kg capacity direct drive self balancing stainless steel body automatic dc injection brake , drying tumbler 60 kg capacity electric heated stainless steel cylinder microprocessor control reversible with cool down feature , front loading washing machine 30 kg capacity electric heated automatic tim temperature and water level control , hydro extractor 30 kg capacity direct drive self balancing stainless steel body automatic dc injection brake , drying tumbler 30 kg capacity electric heated stainless steel cylinder microprocessor control reversible with cool down feature , front loading washing machine 14 kg capacity heavy duty fully automatic microprocessor controlled with digital display

CTN :45333373

26 Jun, 2026 3.33 Crore

Muzaffarnagar - Uttar Pradesh

Tender For corrigendum : supply of interactive panels with cpu (q2) , professional large format display (v2) (q2) , weighing machine , mill house , fully automatic jaggery production unit , solar panel foundation and all related items , structure of complete plant , bought out for complete plan , erection of mill house and boiling house , hdg set , submersible , fire fighting equipment , hcl kit single , oilfree 15 com , air filter , cylinder c2h2 , regulator c2h2 , hood aas , vacuum hot air oven , digital hot air oven , air circulation fan , microprocessor digital temperature indicator , digital timer , heating mantle , digital muffle furnace , single beam uv , double beam uv , digital photo colorimeter , weighing balance , analytical balance cy , water bath , pid temperature controller , atomic absorption spectrophotometer , gas chromatography , fused silica capillary column , gas purification panel , electromechanical voltage stabilizer , carbon steel cylinder , pressure regulator , glassware , servo candy pillopack wrapping machine , horizontal flow wrapepillopack high speed packaging machine , automatic packing machine , vertical single face paper corrugating machine , corrugated sheet pasting machine , eccentric slotter machine , bar rotary cutting creasing machine , stitching machine , paper reel to sheet cutting machine , flexo graphic printing machine , printing machine , manual jar filling machine , manual pouch sealing machine , manual sticker labelling machine , bag sewing machine , bar coding equipment , bar reader machine , projector , laptop , public address audio system , pantry , desktop with accessorie , tv 45 inch screen , solar panel , bio fertilizer plant , cctv unit for control ) /bid number : gem/2026/b/7564787 * /dated: 26-05-2026 & & / bid document 1 / 42

CTN :45533210

23 Jun, 2026 NA

Rohtak - Haryana

Tender For instrument spares for refinery - 3 way manifold, pressure-0 to 120 kg/cm2, with all mounting studs and accessories., air filter regulator, pressure 7 kg/cm2 make- precision, analog input card 8 channel for siemens make dcs part no. 331-1kf01-0ab0 make- siemens, analog ouput card 8 channel for siemens make dcs part no. 332-5hf00-0ab0 make- siemens, bagging machine controller for automatic bagging machine, make power build, model no c750 make- mettler toledo, chute lever sensor high temp. make- yu technologies pvt. ltd,, differential pressure switch, range 0.2 to 6 bar, differential - .25 to 1.2bar, sensing element- copper alloy, elec. ranting- ac-1 : 10 a, 230v ac, make- wika, digital input card 32 channel for dcs part no. 321-1bl00-0aa0 make- siemens, digital output card 32 channel for dcs part no. 322.1bl00-0aa0 make- siemens, discharge valve for pan discharge, input/output connection , double siphon pressure 120 kg/cm2, input/output connection : : threaded, flow meter totalizer, model no. 1008s, input-4 to 20 ma make massibus, flow meter for imbibitions water flow, range -100 tph, line size 4 make- krhne marshall, chute level indicator cum controller, no of sensor 6, output-4 to 20 ma, input supply-230 vol ac make- yu technologies pvt. ltd,, k type thermocouple sensor length -400mm, sensor thickness-6mm, duel output connection, input connection-1/2 npt (m) make- temson, load cell for automatic bagging machine, capacity-110 kg, positioner for control valve i/p 4-20ma, o/p- 4-20ma, make- ytc, pressure gauge range 0 to 160 kg/cm2, dial size 8 inch, input connection (bottom) npt(m) making black & white back ground make- baumer, pressure gauge- range- 0 to 20 kg/cm2, dial size: 150 mm, input connection : (bottom) npt (m), making : black & white back ground, with glycerin filled type make- baumer, pressure gauge- range- 0 to 4 kg/cm2, dial size: 150 mm, input connection : (bottom) npt (m), making : black & white back ground, make- baumer, pressure gauge- range- 0 to 25 kg/cm2, dial size: 150 mm, input connection : (bottom) npt (m), making : black & white back ground, with glycerin filled type make- baumer, pressure gauge- range- 0 to 10 kg/cm2, dial size: 150 mm, input connection : (bottom) npt (m), making : black & white back ground, make- baumer, smart type pressure transmitter , input 0 to 120 kg/cm2, input connection npt (m), hart enabled, with all mounting accessories. make- yokogawa/honeywell, pu tee, 8 mm x make- janatics, pu connector size dia, 8x make- janatics, pu connector both size flange size dia, 8x x 8x make- janatics, pu tube cap. dia 8 x , pressure-30 bar one roll-100 mtrs. make- janatics, rtd pt 100, sensor length 400mm, sensor thickness-6mm, duel output connection, input connection- npt 9m) make temson, sack grip belt for automatic bagging machine, seal kit for automatic bagging machine, model no. dnu 50, for bag clamp cylinder make- festo, seal kit for automatic bagging machine, model no. dnu 40, for course/fine cylinder make- festo, seal kit for automatic bagging machine, model no. dnu 40, for discharge cylinder make- festo, shuttle assembly for automatic bagging machine. make-festo, siemens s7 400 dcs backup batteries part no. 6es7971-0ba00 dc voltage- 3.6 vol make- siemens, single isolator input 0 to 1 amp. ac, output 4 to20 ma,(dual), input supply- 230 vol ac make- massibus, single isolator input 0 to 10 vol dc, output 4 to 20 ma,(dual), input supply- 230 vol ac make- massibus, single isolator input 4 to 20 ma, output 0 to 10 vol dc, (dual), input supply- 230 vol ac make- massibus, smps 24 vol dc source, input voltage: 110 vol dc/ 230 vol ac, output: 24 vol dc make- papper + fuchs, temperature gauge, spec- range 0 to 200 degree c, dial size 150mm, input connection: (bottonm) npt (m), making : black & white back ground, sensor thickness 6mm, capillary type, capillary length 1.5 mtr. make- baumer, temperature gauge, specification range -0 to 150 degree c, dial size: 150 mm, input conne

CTN :45512795

22 Jun, 2026 2.42 Crore

Visakhapatnam - Andhra Pradesh

Tender For tender for supply of seal oil output , accumulator , press switch clutch oil , press gauge clutch , differential pressure device , motor indicating lamp , gasket , pressure switch , temp transmitter pt100 , main pump , temperature transmeter , circlip external f55 , ferrule id 10 steel , set of gaskets for condenser for 144tr acplant for p17 class , kit for power contactor of 160 kw soft starter , motor 22 kw 2 p ip56 sq cage induction 415v 50hz ci f b5 , lamp 380v ac red for lcpb siemens , push button with lamp green 1no - 1nc , catridge for indufil duplex oil filter model idgl-2-226 , pump shaft part no. 2200 for celv 65-250 , soft starter ge astat type qc1ndp 160 kw , mc mccb ge 100a s 400a with aux contact 2no-2nc , mc mccb ge 100a s 400a with aux contact 2no-2nc , semi conductor fuses ge - feraaz 200a 6.611 rd30-xx0315 , main power contactor ge 25a 415v ac 3p power contactor , main power contactor ge 25a 415v ac 3p power contactor , indicating lamp green leb type 110v ac , mcb ge 2 pole 6a 110v ac , emergency push button red 1no-1nc , start push button green 1no-1nc , start push button green 1no-1nc , mc mccb ge 3pole 200a 415v ac s-2ka mc401 , star contactor 415v ac with 1no-1nc coil voltage 110v ac , star contactor 415v ac with 1no-1nc coil voltage 110v ac , delta contactor 415v ac with 1no-1nc coil voltage 110v ac , delta contactor 415v ac with 1no-1nc coil voltage 110v ac , motor protection relay ge- multiline lm 10 , set of indication lamps one of each type for lcp , timer eapl ge etm0010046 1 no- 1 nc , aux contactor ge rl4rd022 td 4no-4nc coil 24v dc , aux contact ge rl4rd040td 5no coil 24v dc , aux contact ge rl4rd040td 8no coil 24v dc , mcb 16a dp siemens , mcb 20a dp siemens , mcb 2a siemens , lamp green 24v dc , lamp amber 24v dc , stay push button epb 1110020 2no 1nc , bridge rectifier ems0011132 25a , contractor ge rl4rd040td 4no coil 24v dc , push button with lamp green 1no - 1nc , indication lamp amber , indication lamp green , indication lamp red , adjustable spanner 12inch , insulated screw driver 3inch , connectors 1-4inch mpt x 1-4inch sae , flare nut 1-4inch , torch light of 2 cells , copper tube 1-4inch x 2mtr , charging adopter 3-4inch fpt x 1-4inch sae , connector 1-8inch mpt x1-4inch sae , gauge adopter 1-8inch fptx1-4inch sae , insulation tape , flexible gas charging line , tong tester , solenoid valve danfoss evra25-24 v dc coil , bridge rectifier usha 25a , annual inspection kit part no. kx127-2 , shaft seal replacement kit part no. kxgs127 , capacity control sub assembly part no.xr16289-0 , microswitch part no. g57057 part of overhaul kit , actuator piston part no.xr12042-2 , end cover - rh side , charging valve , valve needle type 1-4inch npt(m) x 1-4inch ferrule , flexible connection for discharge line , shock mounts for ac plant , bearing cover fixing bolt part no.0036 , temperature switch danfoss rt107 70 to 150 deg c , water line pressure gauges , magnetic level switch for 82.5 tr ac plant for snf class , magnetic level gauge for 82.5 tr ac plant for snf class , transformer 500va 380-24 240v instrans , lamp siemens led green 24v dc , push button siemens e-22 1 no-1 nc green , push button siemens e-22 1 no-1 nc red , semi conductor fuses , temperature indicator 0 to 100 , star bearing kit , metaflex coupling for 65tr , human machine interface hmi-display , thermostatic expansion valve for liquid injection , inspection kit for xrvn-127r4-165-26 , refrigerant suction filter , capacity contorl piston spring , motor replacement gasket & o-ring set , safety valve part no. 07940 , filter element for duplex oil filter , gasket set for condenser

CTN :45384476

17 Jun, 2026 NA

Dharmapuri - Tamil Nadu

Tender For corrigendum : purchase of equipments for mechanical department - purchase of equipments for mechanical department, tail stock assembly medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, working model of fuel supply system - petrol mpfi type petrol multi point fuel injection (mpfi) system for dismantling and assembly practice system type: non-working / cut-section model for study of internal construction construction: actual automotive components or equivalent training model mounted on frame includes throttle body (sectioned), fuel injectors, fuel rail, intake manifold includes fuel pump, fuel tank (dummy), fuel filter, pressure regulator includes ignition system components: ignition coil, spark plug, distributor (if applicable) ecu module (dummy/display type) with wiring layout representation all components cut-open, painted, and clearly labelled provision for manual demonstration of flow path and component interaction mounted on rigid ms powder-coated frame designed for repeated dismantling, assembly, and component identification, hydraulic cylinderbore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply: mounted on training base suitable for dismantling and inspection, hydraulic operated directional control valves (dcv) type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study, bearing with shaft assembly type: dismantling and assembly teaching unit shaft diameter: 30 mm shaft material: en8 steel bearings: deep groove ball bearing (6205 / 6206) housing: cast iron locking arrangement: circlips end covers mounting: bench-mounted / frame mounted unit, coupling unit using driving and driven shafts using plummer block bearing unit the plummer block housing material: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing). sealing: felt seals or v-ring seals (to demonstrate lubrication retention). lubrication: provided with a grease nipple at the top center for manual lubrication practice. the bearing type: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series). bore diameter: standard 25mm or 30 mm. shafting and coupling shaft material: ground carbon steel (en8 or en9) for high surface finish. coupling type: flexible coupling: to demonstrate the bearings ability to handle slight misalignment. rigid flange coupling: to demonstrate traditional direct connection. driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., 3d printing machine build volume(wxdxh) 256 x 256 x 256 mm shell enclosed (plastic & glass) hot end all-metal nozzle 0.4 mm stainless steel included max hot end temperature 300 nozzle diameter 0.4 mm (included) 0.2 mm, 0.6 mm, 0.8 mm build plate compatibility textured pei plate, cool plate, engineering plate, high temperature plate max build plate temperature 100 max speed of tool head 500 mm/s max acceleration of tool head 20 m/s supported filament pla, petg, tpu, pva, pet, abs, asa chamber monitoring camera low rate camera 1280 x 720/0.5fps time lapse supported filament run out sensor :yes control board fan closed loop control auxiliary part cooling fan closed loop control air filter activated carbon filter

CTN :45404122

19 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using

CTN :45476070

15 Jun, 2026 2.37 Crore

Saharanpur - Uttar Pradesh

Tender For audyanik proyog avam prashikshan kendra saharanpur mein nirmaanadhin shahad utkrishthta kendra se sambandhit machinery or parts ki apoorti or establishment ka karya - supply & installation of automatic honey bottling filling machine with sensor based calibrator including with filling range (50 grams to 1000 grams), outout/min (any size within range 3000 to 5000 bpd), filling system (pneumatic vmp system synchronize with servo motor), direction of movement (left to right), number of head/syringe (single), drop controller (y- pneumatic stopper), calibration of machine (automatic with sensor), inlet material stopper (fg valve), feed tank (direct connected), feed tank overflow controller (float type), material feed in m-tank (automatic), heating arrangement in m-tank (water bath system), material shaker in m-tank (electrical shaker), bath temperature & material temperture monitoring system (full auto-control with ccp), electric spply (230 cm v/50hz), tempreture controller (pid), machine dimensions (250 cm x 100 cm x 210 cm (approx) and net weight (300 kg). etc all complete with isi marked., supply & installation of automatic linear capping machine including with output/hour (any size with range 4000 bpd), direction of movement (left to right ), machine dimensions (180 cm l x 90 cm w x 170 cm h (approx)), sensor (panasonic), pneumatic accessories (spac) and no bottle- no cap (yes). etc all complete with isi marked., supply & installation of automatic round bottle sticker labelling machine including with output/hour (10000 bpd), direction of movement (left to right), controlling (micro controller base mm interface), conveyor motor (0.25 hp/415 v/ 50 hz), pressing device motor (60 watt / 220 v/ 50 hz), servo motor (750 watt), label accuracy (+/-1mm), gap sensor (u-type), bottle spacer (electronic), variable speed (40 bpm-max), hmi & plc (7 inch coloured touch pad type), pneumatic (spac), pressure roller (sillicon), adjustment (lead screw), label size (up to 100 mm width), bottle dia (up to 120 mm dia), batch counter (yes) and online data indication (yes) etc. all complete with isi marked., supply & installation of air compressor including with type (reciprocating), tank volume (250 ltr), pressure range (10 kg/ cm 2), no of head-(02 nos.), type (industrial) and operation (continue) etc. all complete with isi marked., supply & installation of induction sealing including with automatic induction sealing machine etc. all complete with isi marked., supply & installation of turn table including with 750 mm dia turn table moc ss304, motor - 0.5 hp/440 vac, vfd - invt/delta and model -cgmp etc. all complete with isi marked., supply & installation of packing conveyor including with 10 feet long packing coveyor, width of conveyor 300 mm, motor - 0.5 hp/440 vac and model - cgmp etc. all complete with isi marked., supply & installation of auto honey feed pump including with automatic honey feed system for filling machine from plant etc. all complete with isi marked., supply & installation of bottle washing machine including with automatic bottle cleaning machine tilting action type etc. all complete with isi marked., supply & installation of particle inspection table including with online particle checker etc. all complete with isi marked., supply & installation of online printer including with online ink jet printer etc. all complete with isi marked., supply & installation of slate chain conveyor including with ss304 slate chain conveyor, motor - 0.5 hpx 3 nos, vfd - 3 nos and guider - as per design etc. all complete with isi marked., supply & installation of automatic wax sheet foundation mill including with sheet making roller set (cell size 5.4 mm, length ,600 mm, dia 200 mm), cold water circulation system 0.5 hp, conveyor belt length - 300 mm, sheet cutting system, water cooling system 1.5 - ton cap, wax malting tank, wax filtration system, ss tray, ss bucket, operation by hmi, dat

Central Government/Public Sector

CTN :45458964

15 Jun, 2026 NA

Multi City - Uttar Pradesh

Tender For auction sale of depot miscellaneous scrap - scrap different type of machine and parts consisting of electrically and manually operated machines, abrassive rail cutter, track temperature, profile welding, grinder, rail drilling machine, hydrau lic jack, reduction gear, vaccum plant, writing jack, pressure control machine, steam generator, punching machine, portable anaesthesia, oxygen holding machine, oil immeresed machine, pentograph, x ray machine, tread mill , boom, air dryer, submersible pump, dg sets, lift parts, and other types of machine items and machine parts and fittings of sorts and sizes with nf attachment. locations:- lying at two places 1- infront of new bin and near tower light. 2- near old canteen and road side. note -1 -loading by purchaser. 2- cutting not allowed. 3-delivery not allowed against part payment. 4- material will be delivered from first location and before second location.

Tube Rota Meter Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector

Central Government/Public Sector