Tender For supply of mechanical seal type cartex-sn with face combinations of carbon vs sic suitable for becacon make de , mechanical seal type cartex-sn with face combinations of carbon vs sic suitable for sulzer make d. m , mechanical seal type y29/d22 with face combinations of gft vs ceramic suitable for antico make acid , mechanical seal type p11/0070 with face combinations of carbon vs tc suitable for kbl make ccw pump , mechanical seal type ll9aw/d040 with face combinations of carbon vs sic suitable for kbl make lpdp n
Tender For tender for supply of essential spares for unit 1 and 2 swas of thermo analysers d d - sodium sensing electrode , on line ross sodium half cell screw cap , part no. 210048 for sodium analyzer orion make model 2111ll , sodium reference electrode , on line ross ultra reference with side arm , part no. 210058 for sodium analyzer orion make model 2111ll , diffusing tubing , part no 211194 , sodium standard solution kit , part no 181140 , high level sodium standard kit , part no 181141 , maintenance kit 2111ll , part no 2111mk , ammonium electrode w screw cap connector , part no. - 100047-wa for ammonia analyzer orion make model 1810 , ammonium reference electrode , part no. - 100056 for ammonia analyzer orion make model 1810 , diffusing tubing kit for ammonia analyzer orion make model 1810 , part no 150060 . thick , 4 ft , ammonia standard solution kit includes two 2 az bottels of standard 1 - 191 ppm nh3 and standard 2 - 1920 nh3 , part no. 181040 for ammonia analyzer orion make model 1810 , acid reagent for ammonia , part no. 181030 , for ammonia analyzer orion make model 1810 , 2l without tubing , hydrazine sensing electrode part no 100022 , hydrazine reference electrode , part no 100056 , diffusing tubing , part no 150060 , hydrazine standard solution 100 ppm , part no 151810 , regulator assembly , part no 2100rg for thermo analyzer , pump assembly , 2111ll , part no 2111pa , electronics faceplate part no 2110xpep for ammonia analyser , electronics faceplate part no 2118xpep for hydrazine analyser
Tender For corrigendum : supply of liquid end assembly with gear box for acid dosing pump, model. no. wd-3000/100, 100, 100 , liquid end assembly with gear box for caustic dosing pump, model. no. wd2250/80
Tender For purchase of equipments - purchase of equipment, bench top glass insitu airlift photo bioreactor1. vessel capacity: 3 liter borosilicate glass (working volume: two to three liters maximum), vessel hxd ratio 4:1 (400x100mm)2. head plate & bottom plate moc: ss 316l3. ports in top plate: ph sensor; dissolved oxygen (do) sensor; pressure sensor; air in and draft tube; air out; acid/base; sampling; and addition port.4. mixing method: ring sparger to create airlift circulation inside the reactor for uniform mixing and better aeration.5. holders for sensor /adapter / blind stoppers in head plate: ph sensor holder; media double inlet for acid/base dosing; air sparger - ring type for airlift application without stirring, air out with exhaust filter and open/close valve; pressure sensor holder; sampling pipe; blind stopper for un used port; unique suitable ss puncturing needles for sampling, air in, air out, inoculum, feed addition.6. ports in bottom plate with stand: port for temperature sensor; heating finger u-tube heat exchanger; drain.7. holders for sensor / adapter / blind stoppers in bottom plate: holder for temperature sensor, heating finger, u-tube heat exchanger.8. sensors: temperature, gel filled sterilizable ph sensor, & pressure sensor.9. controls and display: modular independent system of ph, temperature, pressure with touch screen graphical display & control; two set point control of ph with three-point buffer auto calibration; aeration by flow meter 0-5lpm with air pump; sterilization controls up to 121 without steam generator along with pressure safety mechanism by independent pressure sensor and digital display & control; automatic digital pressure safety and over temperature safety cutoff and alarm; upgradable control system for future prospective as cstr reactor & dissolved oxygen (do).10. measurement and control range: ph: 2-14; process temperature: 20 to 60 ; sterilization temperature: up to 121 ; and pressure up to 15 psi.11. fixed speed peristaltic pump: for acid/base dosing with teflon non spring head. (2 nos)12. cooling system: chiller cum circulator. chiller temperature range 4 to 40 , bath capacity 5l to cool down the reactor after sterilization and to work process temperature below ambient condition.13. illumination system: two illumination assembly with variable intensity control (1000-3000 lux) around the reactor with independent control switch for photobioreactor, or other application and easy detachable if not in use. 14. essential accessories : silicon tubing for acid/base addition (10m); air in and sampling (10m); water circulation (5m); air vent filters 0.2 micron sterilizable (6nos); and silicon septum (25nos)15. starter kit: spare silicon-o-rings for head plate, bottom plate (1no each), all other ports (5nos each), alen key.16. warranty: one year17. support (must): unconditional onsite technical support shall be provided as and when needed. the supplier must provide complete installation and hands-on demonstration of the equipment at the user site upon delivery.18. the vendor should have a registered presence in india with an authorized local service provider in tamil nadu.
Tender For procurement of mandatory spares (not part of amc/rmc) - brass bush rod 50mm2, 2 v , 400 ah transparent lead acid battery, 4 led tube rod (complete set), air break contactor 3tf24, air break contactor mnx-a1(siemens/l&t), air break contactor points for 3tf47, aluminium conductor for 14mva xmer jumper with clamps as per sample 40 meter length, araldite, brass bolt with nut 16mm, 4 inch, brass bolt with nut 18mm, 6 inch, brass bush rod 75mm3, broom, bucholz relay for 14mva xmer, bush rod for 11 kv, cadimium compond, carbon brush (reputed make like merson etc), carbon brush for crane as per sample, cast iron welding rods, ceiling fan, change over switch 250 amps, change over switch 450 amps, compressor head seal (as per sample), contactor for miv panel, cork sheet 1.5 mm,6 x3 , cork sheet 10mm,6 x3 , coupling bush for hs pump as per sample, cup oil seal for bush 11 kv, cutting wheel 4, exhaust fan for workshop 12 , exhaust fan of size 17.5 inches as per sample, filter for hs pumps as per sample, flat iron 5 mm x 25 mm, gate valve 1 inch, gate valve 1/2 inch, gate valve flange type 200mm, gate valve flange type 80mm, gear for 33 kv breaker as per sample, grinding wheel 4, heater pins, heater rods 1000 watt (standard quality), hexa blade, holdite 500 gm tubes, ht tape rolls (10 metre ) 11-33 kv, hv bush seal 132 kv, hydrometer, khadi cloth, lamp 100 watt, leather sheet 8 mm 4 x 10 meter, led 18 watt bulb, link lock (65 mm), lock for 33kv breaker as per sample, lpg gas, lv bush seal 11 kv, mcb double pole 6 a, mcb double pole 10 a, mcb double pole 16 a ( installed at site), mcb double pole 20 a, mcb double pole 25 a, ml4 starter dol, ms flat iron 50x5mm, nabader / felt packing 10mm, neoprene rubber gasket 1/3/5 mm (20/30/150 kg), nrv 1 inch as per sample, nrv 1/2 inch as per sample, old sarees, oxygen gas along with cylinders 150 bar, petroleum jelly, pvc cable kit 1000 sq mm, single core, pvc cable kit 800 sq mm, pvc pipe 1 inch, pvc pipe 2 inch, pvc pipe 3/4 inch, pvc tape rolls, pvc wire 1.0 sq mm (90mtrs coils - cu make), pvc wire 2.5 sqmm 2 core (cu make), ss combine 16 a, ss combine 32 a, reversible starter, rubber bush seal for 14mva xmer, rubber cord 10mm, rubber cord 8mm, seal for high pressure miv pumps as per sample, sf6 gas cylinder, silica gel blue colour, ss coupling, ss nut, bolt 12mm, 16mm,20mm, 30mm (50 each), ss shaft 10 inch long for 75hp as per sample, ss shaft sleeve for 75 hp vt pump, stopper bolt 16mm as per sample, stud ss m12, m16,m20,m30 (length off sizes) with bolts as per sample for cooling system, teflon tape rolls, thermal overload relay for miv panel, welding electrode 3.5 mm sundeep make, welding electrode 4.0 mm sundeep make, wire rope 25mm, wire rope 28mm, wti for 14 mva transformer, transformer oil, heater element for distillation plant, bamboo 15 feet, wire brush, nrv 50mm working pressure 42 kg/cm2 for miv opu as per site, brake liner as per sample, pressure relief valve for miv opu working pressure 42 kg/cm2 as per site - brass bush rod 50mm2, 2 v , 400 ah transparent lead acid battery, 4 led tube rod (complete set), air break contactor 3tf24, air break contactor mnx-a1(siemens/l&t), air break contactor points for 3tf47, aluminium conductor for 14mva xmer jumper with clamps as per sample 40 meter length, araldite, brass bolt with nut 16mm, 4 inch, brass bolt with nut 18mm, 6 inch, brass bush rod 75mm3, broom, bucholz relay for 14mva xmer, bush rod for 11 kv, cadimium compond, carbon brush (reputed make like merson etc), carbon brush for crane as per sample, cast iron welding rods, ceiling fan, change over switch 250 amps, change over switch 450 amps, compressor head seal (as per sample), contactor for miv panel, cork sheet 1.5 mm,6 x3 , cork sheet 10mm,6 x3 , coupling bush for hs pump as per sample, cup oil seal for bush 11 kv, cutting wheel 4, exhaust fan for workshop 12 , exhaust fan of size 17.5 inches as per sample, filter for hs pumps as per sample, flat iron 5 mm x 25 mm, gate valve