Tender For spare parts of scania - connector 1/4" part no 140523, oil collector part no 257319, hand brake valve part no 249914, switch, foot dipper part no 159656, stop light switch part no 158717, t-connector part no 229020, air dryer part no 258985, charging valve part no 215619, elbow connector part no 146235, elbow connector part no 229704, pressure regul. valve part no 5360042991(230787), safety valve part no 293542, valve seat part no 229358, repair kit part no 263664, repair kit part no 263667, bumper part no 249727, stop part no 217280, contact holder part no 235650, sliding contact part no 130770, cap lower part part no 1102372, cap upper part part no 1102371, oil container part no 197804, hydraulic oil pump part no 259310, relay part no 371912, comp circuit part no 259240, relay part no 173554, block terminal part no 353489, socket part no 255080, starting socket part no 231631, battery main switch part no 197811, gear selector (gear box) part no 6695000734(393779), gear selector (transfer box) part no 5895022571(393777), tandom driving cable part no 1149732, bulb 2w/24v part no 258491, panel, switches part no 248821, panel, control lamps part no 248820, map reading lamp part no 218412, control lamp oil pressure part no 239170, control lamp full beam part no 239173, light filter part no 246680, control lamp (direct indicator i) part no 239174, control lamp (gear box oil temp) part no 255073, control lamp coolant temp part no 246856, control lamp (reversing light) part no 249300, plate, blackout lighting part no 391567, techometer part no 258660, comb instrument part no 268353, oil pressure gauge part no 259794, water temp gauge part no 249108, fuel gauge part no 249109
Tender For corrigendum : supply of belt alternator , cabin cyl seal kit , cyl gear seal kit for gear pump , hose assy , hydraulic hose , internal light
Tender For tender for supply of direction control valve , dc male/female connecto , return line filter(rlf) for hydraulic grab uttam/fhe make , 1 inch water pneumatic valve spare parts size - 25nb model - nc-2 way make - kushako pneumatics 1 seal kit , suction filter , o ring for direction control valve (qty- 8 set) , seal kit for hydraulic cylinder (qty-8 set) , seal kit for hydraulic cylinder (qty-8 set) , dowty/ bonded seal size - 1 inch bsp , manifld block , hydex coupling no-48 , gear pump suitable for hydraulic grab having pressure of 220bar and 54lps with inner and outer flange allen key bolts and o-rings , hydex coupling no - 28 , coil for dcv (24 v dc)
Tender For tender for satisfactory trial. , carry out strengthening work using the channels and angles provided by src and irc and conduct a satisfactory trial. , to fabricate the weak sloppy plates of the donali suit fitted on milo from the given ms plate as per the drawing and give a satisfactory trial. , removing the worn out trpf cover fitted on the mill and making and fitting a new cover using the plate given as per the drawing sample and giving a satisfactory trial. , to carry out the work of tipping the teeth of mill rollers and conduct a satisfactory trial. , to carry out the work of chevron cutting as per requirement on mill rollers and give satisfactory trials. , work involving the errectation of broken teeth on the mill s pressure chute repair of worn out teeth via hard facing and conducting a satisfactory trial run , dismantling the old pressure chute errected on the mill completely replacing the corroded section repairing and welding the damaged parts of the ss plate reassembling the unit fitting it onto the mill , fabricate the juice tank for the mill house using the provided 6 8 mm plate and conduct a satisfactory trial run , removing the bottom of the supply juice tank errecting a 12 mm plate in its place and conducting a satisfactory trial. , manufacturing the bed for the s.r.c. and i.r.c. motor gear and conducting a satisfactory trial. , remove the worn out trpf headstock side plate errect a 6mm plate in its place and conduct a satisfactory trial. , fabricating teeth for the hydraulic grab replacing old or damaged teeth with new ones and conducting a satisfactory trial run. , a dismantling old columns beam channels etc. b manufacturing and installing new columns beam channels etc. , removing the old corroded platform and replacing it with a new one. , installing 16 inch 18 inch manholes with blinds , constructing a bed for the pump fitting the pump and motor and conducting a trial run of up to 20 hp. , dismantling fabricating and erecting weak corroded pipe lines up to 12 inch and providing satisfactory leak proof trials. , dismantling fabricating and erecting weak corroded tees up to 12 inch and providing satisfactory leak proof trials. , dismantling fabricating and erecting weak corroded nipples up to 12 inch and providing satisfactory leak proof trials. , dismantling fabricating and erecting a weak throated cross member up to 12 inch and providing satisfactory leak proof trials. , dismantling fabricating and erecting a weak throated band up to 12 inch and providing satisfactory leak proof trials. , dismantling fabricating and erecting a weak throated flange up to 12 inch and providing satisfactory leak proof trials. , dismantling fabricating and erecting a weak sloping reducer up to 12 inch and providing a satisfactory leak proof trial.