Tender For supply of ss sheet sus 301l-dlt - dull finish of size 2 mm x 1250/1500 mm x 2150 mm to jis g 4305 standard. special condition : i) the sheets/plates shall be supplied in bundles with double layer of water proof paper & a bio degradeable plastic sheet of suitable thickness and metal protection in edges. all the sheets up to 2mm thickness shall be protected against corrosion and rust by coating corrosion preventive fluid, soft film, solvent deposited, water displacing to is: 1154. ii)all bundles shall have a minimum of 2 hoopsup to 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling.iii) optimum weight of the bundle should be 2mt+-10%. mechanical damange & corrosionduring transit if any shall be at the cost of supplier. [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]
Tender For rate contract for supply of handpump set and spare parts - supply of handpump set and spare parts, die set 12mm with handle & bits, hydraulic vice 32 mm., heavy duty clamp 32 mm, heavy duty clamp 65 mm, connecting rod vice, pipe lifter spanner for 32mm n.b.pipe., pipe wrench 300 mm, pipe wrench 450 mm, pipe wrench 600 mm, pipe wrench 900 mm, double ended open jaw spanner 17 * 18 in c.v. steel, hacksaw frame, pump bucket (nitrile) for deepwell hand pump(is: 15500 part 7), sealing ring for deepwell handpumps (is: 15500 part 7), hex nut with bolt m 12 * 40, handle axle along with nut & washer for deepwell hand pump (is: 15500 part 4), single side shielded bearing confiming to is: 15500 part 4 suitable for above handpumps, chain nut with bolt m-12x40 (is: 15500 part 4), chain with coupling for deep well hand pump, head for deepwell hand pump (is: 15500 part 4), third plate suitable for deepwell hand pump (is: 15500 part 4) (im-ll), water tank for deepwell hand pump (is: 15500 part 4) (im-ll), connecting rod of 12 mm dia. x 3 mtr. length, i.s.i.marked galvanized steel tubes as per i:s 1239 ( part-1) /2004 amdt.1 to 4 scrwed at both ends as per i:s 554/1999 ( reaffirmed 2004) . one end socketed with isi marked socket as per is:1239 ( part -ii)/1992 ( reaffirmed 2003) and other end protected with plastic thread protector medium class , bore size (nominal)diameter 32 mm , length 3 meter, cylinder assembly i.m.ii, cylinder body with brass liner for deepwell hand pump (is: 15500 part 5), reducer cap for deepwell hand pump (is: 15500 part 5) (im-ll), upper valve along with rubber seat for deepwell hand pump (is: 15500 part 6) (im-ll), upper valve assly suitable for deep well hand pump (im-ll) (is: 15500 part 6) (im-ll), lower valve assembly i.m.ii, hacksaw blade (high speed steel), spacer g.m. i.m.ii, rubber seat lower valve (im-ll), rubber seat upper valve (im-ll), front cover, handle for deepwell hand pump (is: 15500 part 4), stand assembly telescopic for deepwell hand pump, ring spanner 17*18, crank spanner 17*18, i.s.i.marked deepwell handpump set (india mark ii) confirming to i.s.15500 completes with head & handle assembly,water tank,telescopic stand assembly,cylinder assembly along with 12 nos. of 12mm x 3 mtr. length ms electrogalvanised connecting rods made of bright bar and 12 nos.of hot dip galvanised riser pipes 32mm n.b. x 3 mtr. long fitted with socket (made from seamless pipe or machined bar & galvanised) at one end and thread protector at another end.charges etc complete
Tender For corrigendum : miscellaneous items - store 02 part-2 - p u base white paint (01 litter pack) [all vehicle], p u base white paint (500 ml pack) [all vehicle], p u base white paint (200ml pack) [all vehicle], p u pearl white paint (01 litter pack) [all vehicle], p u pearl white paint (500 ml pack) [all vehicle], p u pearl white paint (200 ml pack) [all vehicle], p u clear white paint (01 litter pack) [all vehicle], p u clear white paint (500 ml pack) [all vehicle], p u clear white paint (200 ml pack) [all vehicle], p u paint plen white (01 litter pack) [all vehicle], p u paint plen white (500 ml pack) [all vehicle], p u paint plen white (200 ml pack) [all vehicle], p u thinner (01 litter pack) [all vehicle], p u thinner (500 ml pack) [all vehicle], p u thinner (200 ml pack) [all vehicle], p u surfacer (01 litter pack) [all vehicle], p u surfacer (500 ml pack) [all vehicle], p u surfacer (200 ml pack) [all vehicle], p u paint black (01 litter pack) [all vehicle], p u paint black (500 ml pack) [all vehicle], p u paint black (200 ml pack) [all vehicle], p p primer (01 litter pack) [all vehicle], p p primer (500 ml pack) [all vehicle], p p primer (200 ml pack) [all vehicle], p u putti (01 litter pack) [all vehicle], p u putti (500 ml pack) [all vehicle], p u putti (200 ml pack) [all vehicle], n c putti (01 litter pack) [all vehicle], n c putti (500 ml pack) [all vehicle], n c putti (200 ml pack) [all vehicle], oil paint all colour (01 litter pack) [all vehicle], oil paint all colour (500 ml pack) [all vehicle], oil paint all colour (200 ml pack) [all vehicle], turpentine (01 litter pack) [all vehicle], t cut polish (100 gram) [all vehicle], 3 m rubbing compound (200 gram) [all vehicle], turpentine (500 ml pack) [all vehicle], turpentine (200 ml pack) [all vehicle], water paper 150, 320, 400, 1000 number [all vehicle], masking tape 1 inch 40 meter [all vehicle], rubing compound (200 ml) [all vehicle], dashbord polish pouch [all vehicle], cloth of polish [all vehicle], m s angle [all vehicle], m s flat iron streep [all vehicle], m s square pipe [all vehicle], m s gola pipe [all vehicle], m s nut bolt all types [all vehicle], m s nut bolt washer [all vehicle], c c m s rod, 1/8 inch (250 gram) [all vehicle], m s rod 6 mm [all vehicle], m s rod 8 mm [all vehicle], m s rod 12 mm [all vehicle], m s sheet 10 gaj [all vehicle], m s sheet 18 gaj [all vehicle], steel scru 8 number 3/4 inch [all vehicle], steel scru 8 number 1/2 inch [all vehicle], steel scru 8 number 2 inch [all vehicle], steel scrub washer [all vehicle], electric welding rod 3.15 mm(per packet 90 piece [all vehicle], metal cutting wheel 14 inch [all vehicle], metal cutting wheel 4 inch [all vehicle], grinder wheel 4 inch [all vehicle], paper grinder wheel 4 inch [all vehicle], denting pular patti [all vehicle], welding glass black [all vehicle], welding glass white [all vehicle], welding holder [all vehicle], drill bit 1/8 inch [all vehicle], drill bit 1/2 inch [all vehicle], drill bit 1/4 inch [all vehicle], drill bit 7/32 inch [all vehicle], drill bit 5/16 inch [all vehicle], drill bit 3/8 inch [all vehicle], steel scru kecher [all vehicle], 10 number kecher [all vehicle], 4 inch hinge [all vehicle], 5 inch hinge [all vehicle], 6 inch hinge [all vehicle], 3 inch hinge [all vehicle], handle 10 inch [all vehicle], handle 12 inch [all vehicle], steel spring wire [all vehicle], plywood 10 mm is 710 [all vehicle], plywood 12 mm is 710 [all vehicle], plywood 18 mm is 710 [all vehicle], all size of keel [all vehicle], wood cutter 4 inch [all vehicle], lt wire 04 mm [all four wheeler], lt wire 06 mm [all four wheeler], insulation tape [all four wheeler], packing tape 03 inch [all four wheeler], cello tape 02 inch [all four wheeler], taflon tape 1/2 inch [all four wheeler], double tape 1/2 inch [all four wheeler], fuel linkage with fuse [all four wheeler], fuse all size [all four wheeler], piano switch single [all four wheeler], pull-push switch log tail [all four wheeler]
Tender For bid to ras corrigendum : supply of wx9771615262 drg: 31611770128 rev: 00 condenser air evacuation packa ge (vacuum pump) 30scfm itemid: , w96716155317 drg: - rev: 00 complete vacuum pump (bare shaft vacuum pump) spec: he57016 rev: 04 itemi , w96716155465 heat exchanger for vacuum pump package. spec: he57016 rev: 04 size: - itemid: bh010 , wx9771615270 terminal plate for main motor of vacuum pump size: ----- itemid: bh010 , wx9771615289 heaters for main motor of vacuum pump size: ---- itemid: bh010 , wx9771615297 greasing arrangements for main motor of vacuum pump size: --- itemid: bh010 , w97716155067 bearing for motor of vacuum pump (30 scfm) (1set= 2nos) spec: he57016 rev: 04 size: to s , wx9771615300 terminal plate for rc pump mot or size: ---- itemid: bh010 , wx9771615319 heaters for rc pump motor size: ---- itemid: bh010 , wx9771615327 greasing arrangements for rc p ump motor size: ---- itemid: bh010 , wx9771615335 bearing for for rc pump motor (1set= 2nos) size: ---- itemid: bh010 , w96716155325 main motor for vacuum pump spec: he57016 rev: 04 size: - itemid: bh010 , wx9771615343 motor for recirculation pump for 30 scfm vacuum pump size: --- itemid: bh010 , w97716152033 temperature element for vacuum pump spec: he57016 rev: 04 size: - itemid: bh010 , w97716152041 thermowell for temperature element spec: he57016 rev: 04 size: - itemid: bh010 , w97716155822 pressure transmitter for vacuum pump system: 0-1 bar abs spec: he57016 rev: 04 itemid: b , w96716155244 drg: 31611770051 rev: 00 temperature transmitter for vacuum pump spec: he57016 rev: 04 i , w96716155813 level transmitter for vacuum pump spec: he57016 rev: 04 size: - itemid: bh010 , w96716155210 drg: 31611770047 rev: 00 differential pressure switch for vacuum pump. spec: he57016 rev , w96716155490 flow indicator cum switch for vacuum pump spec: he57016 rev: 04 size: - itemid: bh010 , w97716155733 drg: to suit original supply rev: 00 pressure gauge (0 to -1 bar) itemid: bh010 , w97716155741 drg: to suit original supply rev: 00 pressure gauge (service water) itemid: bh010 , w97716155466 temperature gauge 0-100 deg c, for vacuum pump heat exchanger size: 0 to 100 deg c dim. , w96716155457 differential pressure gauge for vacuum pump package duplex filter spec: he57016 rev: 04 , w97716155849 drg: to suit original supply rev: 00 air flow meter (rotameter) for vacuum pump system s , w97716155547 level gauge for vacuum pump separator tank spec: he57016 rev: 04 size: to suit original , w97716117106 supervision of commissioning lump sum per man day charges at site, including every expe , w97716117114 supervision of commissioning lump sum per visit charges (to & fro) including travelling
Tender For supply, installation and commissioning of distilled water plant for battery grade water for storage lead acid batteries, distilledwater (spec:is-1069-1993 ,plant capacity 150-250 lph ), along with 3 layer hdpe water tank of atleast 100 ltr storage capacity with necessary piping arrangement, 01 no. tds meter, along with standard accessories and items required to make the plant fully functional. installation as per site in lallaguda carriage workshop. [ warranty period: 30 months after the date of delivery ] ]
Tender For supply of cable stoper , fan belt , pipe spring flexible , water seprator , element oil filter , voltmeter , hours meter , fuel pipe for gen set 5.6 kw , fuel pipe
Tender For purchase of non consumable item in hydraulic lab for civil department - bernoullis theorem apparatus(closed circuit)(code e001)bernoulli apparatus flow rate range up to ~20 l/min or more (depending on pump) pump power ~0.5 kw / -1 hp pressure measurement ~0 290 mm to 370 mm wc measuring tank 25 50 l utility 230 v ac, single phase, venturimeter and orifice meter apparatus (closed circuit)(code e002)orifice & mouthpiece apparatus set of orifices: usually 2 sizes (e.g., 8 mm, 10 mm) or more. set of mouthpieces: several l/d ratios (e.g., 10 mm dia with l/d 1, 2.5, 4). sump tank capacity: ~70 100 l. constant head tank: ~20 35 l. measuring tank: ~25 40 l with scale. pump: 0.5 hp monoblock / centrifugal pump (single phase). instrumentation: hook gauge / pointer gauge for head/jet measurement; stopwatch. power supply: 220 230 v ac, single phase., pipe friction apparatus (closed circuit) with all acceeories(code e003)pipe friction apparatus test pipe length ~1 m per pipepipe diameters 12 mm 25 mm (varies)sump tank capacity ~40 l 100 lvolumetric tank ~40 lpressure range (manometer) ~300 500 mm water / mercuryflow rate range 0 60 l/minpump 0.5 hp centrifugal, centrifugal pump testing rig with all accessories(code e004)single speed centrifugal pump testrig (closed circuit) (heavy duty)a. single speed stainless steel centrifugal (mono block) pump set of size 25mm a 1hp, 2880rpm, single phase 50 cycles, 200/220 volts ac electric motor. to discharge about 100lpm at 10 meters head at a single speed of 2880 rpmb. switch and dol starter for the above pump set and an energy meterc. piping system consisting of pipes, valves, and fittings with pressure and vacuum gauges (gi/pvc).fibreglass lined s.s. measuring tank of size 500x500x600mm height provided with a gauge glass, scale and adrainvalve. fibreglasslined s.s. sump of size 1500x500x300 mm height capacity rigid stainless steel frame work compactly fitted with all the above items as a self sufficient package, reciprocating pump testing rig(code e030)reciprocating pump apparatus type of pump single acting reciprocating pumpcylinder bore 50 80 mmstroke length 100 150 mmspeed 30 60 rpmdischarge 5 20 lpmsuction head up to 5 mdelivery head up to 20 mmotor power 0.5 1 hpmotor speed 1440 rpmpower supply 230 v ac, single phasepressure gauge range 0 5 kg/cm vacuum gauge range 0 760 mm hgmeasuring tank capacity 30 50 litersmaterial cast iron pump, ms framedrive belt drive / direct coupling, mouthpiece & orifice setup(code e002 )experiments : to determination of cd, cv, and cc of venturi meter.specificationsventuritype : acrylicsize/dimension : 350mm 350mm 600mmnominal size : 25 mmend connection : gi pipeusage/application : laboratorybody material :stainless steelorifice meterapparatusexperiments : to determination of cd, cv, and cc of orifices meter.specificationspump : hp centrifugal pump.ac motor : hp 230v ac.supply tank : 120 ltrs. made of ms with frp lining.measuring tank : 40 ltrs. made of ms with frp lining and fitted with piezo meter tube & scale.piping &fittings : gi/pvc with necessary valves.fitted with u-manometer with mercury.control panel : 1hp dol starter.digital timer : mcb load and line indicator.