Tender For work as per boq - demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition). , m&l for cutting chases, in brick wall, pinning in and making good to facing where required and pointing in cement mortar (1:3), to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing etc and making good the disturbed surface, cutting exceeding 20cm girth complete , m&l for complete removal of existing treatment and levelling of wall surface using mechanical/electrical operated sanding/scraping machine with inbuilt vaccum suction system to suck the existing treatment as retrieved by scrapping/sanding etc and applying one coat of water proofing wall care putty of 3mm thick for obtaining smooth paintable surface complete , m&l for applying two coats of 100% premium acrylic emulsion paint(using air-less paint sprayer) having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over wall surfaces by using air-less paint primer sprayer including preparation/levelling of old surface of wall using manual sand papers , m&l for applying one coat of synthetic enamel paint after preparation of old steel sufaces of any description over 10 cm girth or width complete
Tender For corrigendum : supply of battery operated rotary hammer drill st machine complete with battery pack (02nos), charger, hammer drill bit (4 cutting edge made of tungsten carbide) 10mm 12mm and 16 mm, narrow flat and pointed chiesel single impact energy 2.6j, 1050 rpm, hammer drilling range 4mm to 28mm, optimum drilling range 6mm to 18mm, weight of tool must be less than 3kg, active torque control (atc), inbuilt active vibration reduction (avr), chiseling, chipping, depth gauge, removable chuck, reverse mode, torque clutch, triaxial vibration value for hammer drilling into concrete must be less than 11 (m/s2), triaxial vibration for chiseling in concrete must be less than 6(m/s2), 1st battery 22 (v) 8amp, weight less than 1.5kg, 2nd battery 22 (v)-4amp, weight less than 1.0kg, battery working range minus()17 degree to 60 degree, state of charge display, upgraded durability and battery monitoring ac??? built-in battery health tester, sealed electronics, shock absorbers and reinforced housing to better protect against jobsite conditions, battery charger i/p 230v, o/p power 240, o/p current 9.6amp, state of charge display. , supply of electrically operated concrete breaker with self sharpening chisels (four numbers). 02 nos 36 cm narrow flat chisels, 01 no 36 cm pointed chisel and 01 no 50 cm narrow flat chisel. the tool shall be of the following specification i.e impact energy 35j, impact frequency 1800, vibration to body less than 5m/s2, weight of concrete breaker tool must be less than 15kg, power i/p approximate 2.1kw, brushless motor, detachable supply cord, three lubricating chambers inside machine
Tender For annual rates for supplying material for various types of construction work for bandhkam department of dahegam nagarpalika.(second attempt)-, cement (opc 53 grade isi mark) 50 kg bag, , kapchi 20mm size, , |for sand and plaster, , etel, , |maram, , mat/d, , garbage, , round (40 to 50 mm size) for concrete, , kawori waste/stone dust, , ih b metal 25 to 90 mm size, , black metal 25 to 40 mm size, , black metal 40 to 63 mm size, , b t ruble (300 to 400mm size), , |gravel 10 to 12 mm size, , |ronda/construction west khada puran maate, , glaze tiles, , |rough green kota stone 2.5" t0 3" thick (for road road) (a) r' * 1' size, , |rough green kota stone 2.5" x 3" thick (for road road) (b) r' * 1' 6" size, , |kota stone 25mm thickness polished kota stone (for flooring), , |indian type w.c.pan (complete set) 580mm size, , european type w.c.pan (complete set), , |stoneware "p" or "s" trap, , |lokhandana bars (a) tmt bars, , ???????? ????? (b) binding wire, , ???????? ????? (c) mild steel bars, , chane banyak, , oil paints color, , distemper color, , with centering plate and support, , mixer machine (for 8 hours with diesel and machine operator), , rcc pipe with collar (1 meter length) will have to be delivered as per the instructions of the municipality. (a) 6" dia, , rcc pipe with collar (1 meter length) will have to be delivered as per the instructions of the municipality. (b) 9" dia, , np-? r.c.c. pipe with collar will have to be delivered as per the instructions of the municipality. (? meter including collar) length(a) 300 mm dia, , np-2 rcc the pipe will have to be delivered along with the collar as per the instructions of the municipality. (with collar) (1 meter length) (b) puff mm dia, , np-? r.c.c. pipe with collar will have to be delivered as per the instructions of the municipality. (? meter including collar) length) (c) 600 mm dia, , np-? r.c.c. pipe with collar will have to be delivered as per the instructions of the municipality.(? with collar) (? meter) length(d) 750 mm dia, , np-? r.c.c. pipe with collar will have to be delivered as per the instructions of the municipality. (? meter including collar) length(e) 900 mm dia, , np-3 rcc pipe with collar will have to be delivered as per the municipality's instructions. (with collar) (a) 150 mm dia., , np-3 rcc the pipe will have to be delivered with collar as per the notification of the municipality. (with collar) (b) 200 mm dia., , np-3 rcc pipe with collar will have to be delivered as per the instructions of the municipality. (with collar) (c) 300 mm dia, , np-3 rcc pipe with collar will have to be delivered as per the instructions of the municipality. (with collar) (d) 4 50 mm dia, , np-3 rcc pipe with collar will have to be delivered as per the municipality's instructions. (with collar) (e) 600 mm dia., , np-3 rcc the pipe will have to be delivered with collar as per the notification of the municipality. (with collar) (f) 750 mm dia., , np-3 rcc pipe with collar will have to be delivered as per the notification of the municipality. (with collar) (g) 900 mm dia, , np-3 rcc pipe with collar will have to be delivered as per the notification of the municipality. (with collar) (h) diameter mm, , np-3 rcc pipe with collar will have to be delivered as per the municipality's instructions. (with collar) (i) 1400 mm dia., , np-3 rcc pipe with collar will have to be delivered as per the instructions of the municipality. (including collar) (j) mm dia, , 2' * 1' or 2' * 1' kota stones of 6" size and 2.5" to 3" thickness. (minimum 1 in each) 80 bare stones will have to be shifted as per the information of national highway.), , white cement, , pvc tank isi mark, , lokhandna doors with red oxide color, , lokhandani bari-jali with red oxide color, , watering-rolling on metalling work. rolling work up to 8 to 12 tons., , rough kota stone 1.5" to 1.5", , 35 ton capacity fiber reinforced heavy duty manhole frame with cover (square frame with round cover), , 20 ton capacity fiber reinforced hea
Tender For supply of barrack and road or electric and mechanic items - aium bow handle 200mm , aium haples and staples 150mm long , alum tower bolt 200mm make , aluminium handle 100 mm make , aluminium handle 150 mm make , butt hings 200mm , butt hings 50mm , butt hings 75mm , cement bag of 50 kg each , cp central hole mixture 15 mm for wash hand basin , cp concelled stop cock 15mm , cp health faucet 15mm x 8mm dia 1 point 2 mtr tube , cp jet spray 15mm with 1 point 5 mtr tube , cp sink coupling 50mm dia , cp sink mixture 15mm with regular spout w m , cpvc coupling 15mm , cpvc elbow 15mm , cpvc female adopeter brass 15mm , cpvc female adopeter plastice 15mm , cpvc male adopter brass thread size 15 x 25mm dia , cpvc pipe 15mm 10 ft length , cp curtain bracket fancy type 25mm , cp curtain bracket plain chromium plated 25mm dia fancy , cp curtain rod 20mm dia , cp curtain rod 25mm dia , drill bit size 6mm for drill machine , drill machine bit for concrete 12mm , drill machine bit for concrete 8mm , gi wire mesh 2 ft wide , gi wire mesh 4 ft wide , granding blade 4 inch , helical door spring 150 mm , hydraulic door closer classic 90 degree universal , internal kit for flush cistern with dual flush pvc , internal kit for flushing cistern single flush pvc , looking mirror 450 x 600 mm aluminum frame pvc , ms butt hinges 100 mm , ms handle for window , m seal 100 gm pkt , oil putty , piano type hinges ss 20 mm thick and 6ft long , plain glass sheet 3mm thick size of each sheet not exceed 0 point 5 sqm , plywood 3mm of size 8 ft x4 ft , plywood 4mm of size 8 ft x4 ft , plywood 6mm of size 8 ft x4 ft , pvc angle cock 15 mm , pvc angle cock 15 mm two way , pvc ball cock 15 mm with ball and rod , pvc ball cock 20 mm with ball and rod , pvc bib cock 15 mm , pvc bib cock 15 mm long body with flanged , pvc connection 15 x 450 mm , pvc connection 15 x 600 mm , pvc flushing cistern 10 ltr cap , pvc health faucet 15mm with tube 1 point 5 mtr and hook , pvc jet spray 15mm with 1 point 5mtrs connecting tube , pvc overhead shower round 3 inch , pvc pillar cock 15 mm , pvc pillar cock 15 mm swan neck , pvc stop cock 15 mm , pvc tank cover lid , pvc toilet seat cover for ewc , pvc waste coupling 32mm dia full threaded , pvc waste pipe 32 mm , rubber beading 75mm wide 15mm , ss concealed curtain socket 25mm , ss curtain support set 25mm , stainless steel kitchen sink coupling 114mm , steel but hings 150mm , tank connection nipple 25mm , tank nippe 20mm , teflon tape 20 to 40mm width 21 to 30m long , tower bolt aluminium 100 mm , tower bolt aluminium 150 mm , urinal white pipe 45mm , viterous china wash hand basin size 530 x 425mm , vitreous china squatling pan orisa pattern of size 580 x 440mm , water storage tank 1000 ltr cap d l , water storage tank 500 ltr cap d l , aluminium door stopper single , aluminium door stopper double , wooden cutter blade , drill bit size 14mm , iron pipe clip 20mm , iron pipe clip 15mm , iron hook for gi pipe 15mm , iron hook for gi pipe 20mm , leakage repair water proof tape 5cm x 5m alu foil tape water proof adhesive for water tank and pipe , 2 ft x 2 ft recess ceiling light 36 watt , 2 ft x 2 ft surface ceiling light 36 watt , ac single phase static energy meter capacity 5 to 30 amps lcd type , ac three phase static energy meter capacity 5 to 20 amps lcd type , aluminium lugs 150 sqmm , aluminium lugs 185 sqmm , aluminium lugs 300 sqmm , aluminium lugs 400 sqmm , aluminium lugs 50 sqmm , aluminium lugs 70 sqmm , building security light 25 w , capacitor 2 point 5 mfd , capacitor 4 mfd with copper therminal , capacitor 6 mfd , pvc casing capping 20mm , pvc casing capping 25mm , ceiling fan 1200mm w o regulator , copper cable three core 1 point 5 sqmm for ac , copper cable three core 2 point 5 sqmm for ac , electric cable 1 point 5 sqmm roll of 180 mtr , electric cable 2 point 5 sqmm rol of 180 mtr , electric cable 4 sqmm rol of 180 mtr , electric plug top 16 a , electric plug top 6 amp , extension board heavy duty , fan regulato
Tender For supplying construction material for repair and maintanance work at badnawar - 6mm machine broken aggregate including supply at site, 10mm machine broken aggregate including supply at site, 12mm machine broken aggregate including supply at site, 20mm machine broken aggregate including supply at site, gsb includding supplying and rollong at site complete, river sand including supply at site, balu sand including supply at site, moorrum with filling jcb including supply at site, cement isi mark 43 grade or 53 grade including supply at site, stone dust including supply at site, brick open bhatta supplying at site, black soil, iron jaali angle tube chamber plate aal type including filling, hot rolled hyysd bars isi marked 6mm, hot rolled hyysd bars isi marked 8mm, hot rolled hyysd bars isi marked 10mm, hot rolled hyysd bars isi marked 12mm, hot rolled hyysd bars isi marked 16mm, roller including fuel operater, painting steel work including material etc work, painting rcc brick work including material etc work, tiels vetrified, red farsi 40mm thk, kota stone 20mm thk, granite stone 20mm thk, jcb including fuel and operator, tractor including fuel and operator, concrete fiory including fuel and operator, mixer machine ncluding fuel and operator, poclane including fuel and operator, oil bound distemper of approved brand isi mark, cement concrete work m-20 including labour all complete, centering supply fitting workcomplete including laboure, chamber drainage cover, plaster including labour work 6mm, 12mm, 15mm, paver block 80mm thk fitting complete, rcc pipe np3 200mm dia, rcc pipe np3 300mm dia, rcc pipe np3 400mm dia, rcc pipe np3 600mm dia, rcc pipe np3 1200mm dia, writing work on stone all types, oil paint, pvc pipe 6kg 150mm dia, pvc pipe 6kg 100mm dia, pvc pipe 6kg 200mm dia, gi sheet including fitting work, pot hole repair of existing bituminous /concrete roads with hot mix bituminous material all compltete, ss railing work including fitting all complete, concrete breaker machine, acp pannel installation supplying erection all complete, urinal fitting all complete, indian pattern toilet seat fiiting all complete
Tender For supply of matrials to constraction katageri nrlm shed - broken stone aggregate 40 mm size (kat01), broken stone aggregate 20 mm size (kat01), broken stone aggregate 12 mm to 10 mm size(kat01), coarse sand (zone iii) (kat01), portland cement (kat01), mixer (concrete) - 1 cum capacity (kat01), add watering charges at 1 percentage on material (kat01), add sundries charges at 1 percentage on material (kat01), transportation/loading and unloading of material/lifting of material /wastage/unforeseen charges/miscellaneous which are necessary during execution. (kat01), granite/trap broken metal 100 mm and down size (kat01), plasticizer / super plasticizer (kat01), hom of vibrator 0.71 days (kat01), tmt bars fe 500 (kat01), binding wire (kat01), size stone 20 x 20 x 25 cms (kat01), bond stone 20 x 20 x 45 cm (kat01), boulders (kat01), mixer (concrete small used in culvert) (kat01), mason class i (with tools) (kat01), mason class ii (with tools) (kat01), stone chistler class ii (kat01), add sundries charges at 1 percentage on labour (kat01), add watering charges at 1 percentage on labour (kat01), silver oak or equivalent planks 38 mm thick (kat01), casurina poles 100 - 150 mm (kat01), add handling , loading and unloading at 2 percentage on material (kat01), add sundries charges at 2 percentage on material (kat01), casurina poles 75 - 100 mm dia (kat01), jungle wood runners and planks (kat01), solid concrete blocks (40 x 15 x 20 cms)-4.00 n/sqmm (kat01), add handling , loading and unloading at 1 percentage on material (kat01), solid concrete blocks (40x10x20 cms)-4.00 n/sqmm (kat01), add providing and removing scaffolding at 3 percentage on labour (kat01), vitrified tiles 600x600 mm (kat01), mathi/nandi wood planks for panels 25 mm thick (kat01), add cutting and other wastage 5 percentage (kat01), hom of machinaries for planing (kat01), mathi/nandi wood scantling (kat01), unit cost as per the specification (kat01), m.s rods (kat01), ms flat (kat01), fitter class i (kat01), welder grade i (kat01), add hom of welding and grinding machine at 4 percentage on material (kat01), ready mix primer paint (ready mix red lead paint) (kat01), add wire brush, fine steel wool, putty, sand paper, at 3 percentage on cost of paint (kat01), painter class i (kat01), enamel metal paint (kat01), add brush at 1 percentage on cost of paint (kat01), ceramic tiles 30 x 30 cms (kat01), white cement (kat01), plastic emulsion paint (kat01), add brush, putty, sand paper, roller at 5 percentage on cost of paint (kat01), water proofing cement paint (kat01), add brush, putty, sand paper at 2percentage on cost of paint (kat01), liquid wood filler (kat01), add brush, putty, sand paper at 5 percentage on cost of paint (kat01), enamel paint (kat01), polyenthylene water storage tank of specified capacity l (kat01), labour charges for lifting and placing in position and making connection at 7 percentage on material (kat01), handling loading and unloading 3 percentage on material (kat01), indian type water closet of size 580 mm of specified make with footrests (kat01), a 100mm s or p trap (kat01), add white lead paint, gasket, cement, sand for making good the wall and floor at 2 percentage on material (kat01), add cement sand and grit 1 percentage on material (kat01), licenced plumber with tools (kat01), add 5 percentage for fittings and wastage charges (kat01), polythylene pipes high density 25mm external dia (kat01), cost of 6.5mm m.s. coil (kat01), fabrication charges. (kat01), labour charges for handing errection of rcc rings etc. at 5 percentage (kat01), transportation charges of materials beyond 5 km at 10 percentage (kat01), rcc cap 1000 mm dia, 100 mm thick (kat01), pvc pipe of 10kg/cum,90 mm (kat01)
Tender For supply of matrials to constraction of samashan at konkonakoppa - a 12 x 12 gauge g.i. wire 100 mtr at ts. 8.00/ per m (konkonakoppa samashan), tractor - 40 hp (konkonakoppa samashan), laboratory asst. (sslc passed)/mate/supervisor (konkonakoppa samashan), moulding charges for casting gaurd stones (konkonakoppa samashan), transportation loading and unloading at1% on material (konkonakoppa samashan), tools and plants at 2% on material (konkonakoppa samashan), hom of cutting and grinding machine - 1 (konkonakoppa samashan), mechanic class ii/mechanic hmp grade i/eme grade (konkonakoppa samashan), anticorrosive bituminous paint (black) (konkonakoppa samashan), ball bearing hinges heavy duty (konkonakoppa samashan), cast iron spike (konkonakoppa samashan), a 40 x 6 mm ms plates (konkonakoppa samashan), a 36 mm x 6mm ms plates (konkonakoppa samashan), a 16 x 16 mm ms square rod (konkonakoppa samashan), a 50 mm dia ms hollow pipe b class 14 gauge (konkonakoppa samashan), welding charges at 10% on material (konkonakoppa samashan), fitter class i (konkonakoppa samashan), aluminium paint (konkonakoppa samashan), wire mesh 50mm x 50mm (konkonakoppa samashan), add brush, putty, sand paper at 2% on cost of paint (konkonakoppa samashan), water proofing cement paint (konkonakoppa samashan), mason class i (with tools) (konkonakoppa samashan), unit cost as per the specification (konkonakoppa samashan), tools and plants and electrical charges at 2% (konkonakoppa samashan), add brush at 1% on cost of paint (konkonakoppa samashan), enamel metal paint (konkonakoppa samashan), add handling , loading and unloading at 2% on material (konkonakoppa samashan), add providing and removing scaffolding at 3% on labour (konkonakoppa samashan), painter class i (konkonakoppa samashan), add wire brush, fine steel wool, putty, sand paper, at 3% on cost of paint (konkonakoppa samashan), ready mix primer paint (ready mix red lead paint) (konkonakoppa samashan), hom of cutting and grinding machine (konkonakoppa samashan), add (konkonakoppa samashan), hom of welding and grinding machine (konkonakoppa samashan), welder grade i (konkonakoppa samashan), corbon electrodes (konkonakoppa samashan), anchor bolts 750mm (konkonakoppa samashan), base plate / base plate (konkonakoppa samashan), gusset plates 6 mm thick (konkonakoppa samashan), ms angle iron 40mm x 40mm x 6mm, 23 metre in length at 3.5 kg per metre (konkonakoppa samashan), ms angle iron 50mm x 50mm x 6mm, 33.8 metre in length at 4.5 kg per metre (konkonakoppa samashan), binding wire (konkonakoppa samashan), tmt bars fe 500 (konkonakoppa samashan), add sundries charges at 2 % on material (konkonakoppa samashan), add handling , loading and unloading at 1% on material (konkonakoppa samashan), casurina poles 100 - 150 mm (konkonakoppa samashan), burnt bricks class 35 (non modular) (konkonakoppa samashan), mixer (concrete small used in culvert) (konkonakoppa samashan), bond stone 20 x 20 x 45 cm (konkonakoppa samashan), size stone 20 x 20 x 25 cms (konkonakoppa samashan), boulders (konkonakoppa samashan), hom of vibrator 0.71 days (konkonakoppa samashan), plasticizer / super plasticizer (konkonakoppa samashan), add sundries charges at 1 % on material (konkonakoppa samashan), add watering charges at 1 % on material (konkonakoppa samashan), mixer (concrete) - 1 cum capacity (konkonakoppa samashan), portland cement (konkonakoppa samashan), broken stone aggregate 12 mm to 10 mm size (konkonakoppa samashan), broken stone aggregate 20 mm size (konkonakoppa samashan), transportation/loading and unloading of material/lifting of material /wastage/unforeseen charges/miscellaneous which are necessary during execution. (konkonakoppa samashan), add watering charges at 1 % on labour (konkonakoppa samashan), add sundries charges at 1 % on labour (konkonakoppa samashan), coarse sand (zone iii) (konkonakoppa samashan)
Tender For 3. s/i of 06 nos open gym in distt kanpur dehat - elliptical machine dimension 1200x900x450mm, combined climber/chinup bar two peopler dimension 22, rowing machine dimension 1280x800x1150mm, arm shoulder wheel dimension 600x300x1500mm, steppertwister dimension 1200x750x360mm, parallel bar dimension 2000x600x1200mm, dual ab board dimension 1500x1500x1200mm, two people sitting pushing and pulling exerciserdimensions 1800x900x1500mm, frieght of equipment - 5%, installation of gym equipment, supply and fixing of sign board, photography charge, earth filling, earth work excavation in trench for foundation ,pipes ,cable etc in ordinary soil(loan clay or sand) including upto1.5 m lead upto 50 m dressing of side and ramming of bottom and disposal of surplus excavated earth as directed by the engineer -in -charge with a lead 50m .ref to dsr/pwd spec.2.6(2.6.1), providing and laying in cement concrete 1:6:12(1cement:6 coarse sand:12 graded brick ballast 40 mm nominal size) and form work,curing complete as per technical specificatation .ref to dsr/pwd sch273, m-150 class brick work in foundationand plinth in1:4 cement and coarse sand mortar with all complete upto the plinth including supply of all matrials , labour ,t &p etc required for proper completion of work..ref to dsr/pwdspec-6.1.1, 12 mm thick plaster singel coat on fair side of 1:4 one cement and four coarse sand complketeitem.ref to dsr/pwd spec-13.4.1, providing and laying of 60 mm thick interlocking tiles completeitem,mord-1500(6.7)(2)