Latest water vapor cryotraps Tenders | Government water vapor cryotraps Tenders

State Government

CTN :40271711

15 May, 2025 4.94 Lacs

Baddi - Himachal Pradesh

Tender For (sh replacement of centrifugal pumping set 40 hp of lift water supply scheme sheran thana (dharampur old) both pump and motor with allied accessories)

State Government

CTN :40271713

15 May, 2025 3.94 Lacs

Baddi - Himachal Pradesh

Tender For (sh replacement of centrifugal pumping set 30 hp of lift water supply scheme mandhala i both pump motor with allied accessories)

Central Government/Public Sector

CTN :40273590

30 May, 2025 45.00 Lacs

Gurgaon - Haryana

Tender For ca no. ge af no.1/gur-15/2025-26 repair and maintenance of chlorination system, centrifugal pumping set, yield development, sumersible pumping set, repair of borewell line other connected works for water supply installations at afstation gurgaon un

State Government

CTN :39996366

10 May, 2025 3.45 Crore

Kanchrapara - West Bengal

Tender For corrigendum : supply, storage, installation, commissioning and trial run of electro-mechanical equipment at raw water and clear water pumping station under kanchrapara municipality. - for rwps, supply, delivery , storage, installation, testing & commissioning of vertical turbine type centrifugal pump with cashion pipe ,column assembly, discharge head, sole plate, motor stool and all other accessories all complete of 750m /hr discharge at a head of 29 mtr at duty point as per technical specification . maximum allowable speed of pump shall be 1000 rpm., supply, delivery , storage, installation, testing & commissioning of vertical, scim ,tfec, 110 kw (minimum), 415 v 10% , 50hz 05%, speed 1000 rpm (syn) , to vertical pump duty motor to match with pump at sl no- (1) complete with coupling hub and all other accessories as per specification., supply, delivery , storage and installation at site of ms pipes, specials, joints, flanges as per specification and technical offer. (for both individual pump delivery pipe and extended part of common manifold if required) ., supply, delivery and installation and commissioning of valves complete at site with fixture as per specification and technical offer & as follows :-, di butterfly valve for delivery side of pump fitted with electrical actuator suitable for local and control desk operation and display system for the individual pump delivery pipe line. (350 mm minimum))(pn 16 type), di non-return valve for individual pump delivery pipe line. (350 mm. minimum))(pn 16 type), supply, delivery at site and storage of m.s. dismantling joint assembly for the individual pump delivery pipe line as per specification (350 mm minimum)., supply, delivery ,storage and installation at site of pressure gauges complete with fittings and fixture as per specification, pressure gauge for delivery side (0 10 kg / cm2), supply, delivery ,storage and installation at site of pressure transmitter complete with fitting and fixture as per specification as follows:-, pressure transmitter for delivery side ( 0 10 kg / cm2 ), supply, delivery at site and installation of m.s. structural materials for cable tray / rack, panel installation supports, pipes & valves supports, fabricated stairs & all other fabrication work., lt panel, modification / retrofitting/expansion/addition of the existing pmcc with supply , delivery & installation of a new additional motor starter feeder at rwph in order to accomodate the extra pump-motor feeder of requisite rating not less than 110 kw .the modification/addition should match/synchonise the existing panel and should ensure smooth operation of the complete panel as a single entity and should be fit to install at the existing pump house., retrofitting of existing control desk at site with supply,wiring, installation of additional items like temparature scanner , multifunction meter , microprocessor based position indicator, digital pressure indicator,tnc switch, push button switch, indication lamps etc .as required to complete for the new pump motor set., supply ,delivery, laying, installation of power cable of adequate size from motor feeder to motor .(min. 2 run x 3core , 185 sq mm xlpe armoured al. for each feeder), supply ,delivery, laying, installation of power cable of adequate size and length from pmcc to motor space heater . (min. 3 core 2.5sq mm. armoured cu for each motor), supply ,delivery, laying, installation of power cable of adequate size and length from pmcc to valve actuator etc. elsewhere required. (min . 4 core 2.5 sq mm. armoured cu), making end termination of all the power cables as stated in sl no 11,12,13 with all necessary equipments like termination kits(dry type), lugs , glands etc , installed for the modification job., supply ,delivery, laying, installation of control cables of different size as required for the purpose and length for completing the different control connections between control desk, motor feeders , lpbs, pmcc etc.to the

State Government

CTN :40248894

15 May, 2025 4.94 Lacs

Baddi - Himachal Pradesh

Tender For (sh replacement of centrifugal pumping set 40 hp of lift water supply scheme nandpur lodhimajra both pump motor with allied accessories).

CTN :40218970

12 May, 2025 88

Yelahanka - Karnataka

Tender For pump motor repair - guide vane, oil seal steel bush(oil seal sleeve), oil seal(pump oil seal), intermediate piece (i.p.) with i.p. leaded bronze bush, pump bowls, rewinding of motor of 20 hp, rewinding of motor of 17.5 hp, rewinding of motor of 15 hp, rewinding of motor of 12.5 hp, rewinding of motor of 10 hp, rewinding of motor of 7.5 hp, rewinding of motor of 5 hp, rewinding of motor upto 3 hp, transportation of pumping machinaries, motor base with pin, circlips(small), bearing (gun metal bush) centrifugal cost aluminium bronze bearing bush, studs and nuts, tip carbon/ferrode padding, thrust bearing block assembly (tb bottom), carbon housing(tb plate), lock ring(circlip big), lower housing, upper housing, lower flange, upper flange, labour charges (overhauling of pump only), brass filter, strainer, cable guard, pump coupling (stainless), pump key (stainless steel) upto 8 stages, pump shaft (stainless steel) counter less ground with key way upto 8 stages, allen screw, steel bush (i.d.o. ss sleeve), d.o. bearing( i.d.o lb bush), discharge outlet (d.o.) bearing(lb bush) and d.o steel bush(ss sleeve), impeller shell moulded with aluminium & bronze, supply and fixing of voltmeter, supply and fixing of ammeter, supply and fixing of led indicator, supply and fixing of wiring kit(sd upto 25hp), supply and fixing of wiring kit(dol upto 7.5hp)(mr), supply and fixing of no-volt (nv) coil, supply and fixing of terminal plate (connector 60a), supply and fixing of terminal plate (connector 30a)(mr), supply and fixing of ryb rotary switch(volt selector), supply and fixing of single phase preventer(20 to 30 hp), supply and fixing of single phase preventer(7.5 to 15 hp) (mr), supply and fixing of 15 amps relay (mr), supply and fixing of 23 amps relay (mr), supply and fixing of 33 amps relay, supply and fixing of 25 amps contactor, supply and fixing of 16 amps contactor(mr), erection of panel board & ms box (outdoor type) (gulbarga pred, pg.no.57, lt.no.12.2), supplying and fixing angle iron frame work fabricated out of m.s. angle iron and m.s. flat with bolt, washer etc and painted with 2 coats of red oxide and then two coats of approved paint 75x75x6mm (pwd ele sr 2014-15, pg.no.49, lt.no.6.39.3), refilling available earth around pipe lines, cable in layers not exceeding 20cms in depth, compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specification pre sr 2011-12, p-3,1-6., labour charges for laying u.g. cable upto 3.5 core 25 sq.mm as per pwd electrical sr 2010-11, p-68,1-1, class a pvc cable, lifting of struck up submersible pump set above 300 ft (bwssb sr 2017-18/o150g/sl no.27), lifting of struck up submersible pump set upto 300 ft (bwssb sr 2017-18/o150g/sl no.26), labour charges overhauling, lifting of submersible pumpsets, re-errection charges of pumping machinery including overhauling and painting, cable joint, g.l. pipe threading including transportation, labour charges (for over hauling), supply and fixing of ct coil 50/5 & 75/5, supply and fixing of blade set 25a, supply and fixing of blade set 16a(mr), supply and fixing of hylum brand hand plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc and fixing of exciting wood or metal box using nf screw , supplying and fixing polished wood board made out of not less than 15mm thick planks at both sides with planks made out of not more than 2 pieces and fixing the same to the wall using tapered wooden plugs screws etc, fabricating, supplying and mounting ms box made out 14 swg suitable for foor/wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front over equipped with temper proof locking arrangements with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enamelled metal paint etc., com

CTN :40135848

17 May, 2025 NA

Hooghly - West Bengal

Tender For supply of other section , m and l for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces width or girth exc 10 cm including preparation of surfaces all as specified and as directed. , m and l for three coats of white washing on new plaster and unplaster of wall surfaces including preparation of wall surfaces complete all as specified and as directed. , s and f steel stainer for sewage sumps of different pores as specified and directed by engineer in charge , suppy of stand by non clogging pump of 5hp 1520 lpm with all accessories and fittings as specified and directed by engr in charge , heavy duty double tank type chemical dosing system consist of service tank 150 ltrs capacity with dosing system plunger type , s and f gi strip 25x4mm as earthing lead bolts nuts checknuts and washers all as specified and directed , material and labour for earthing complete with galvanized steel plate electrodes of size 600mm x 600mm x 6mm thick , pumping out sewage water from the existing sumps of sewage plant pump house with the help of non clogging of pump any kind capacity of pump set not less than 2160 lpm , lifting the non clogging pump set electrically operated by 15hp 20 hp 3 phase motor incl column pipe line shaft etc , dismantling of non clogging submersible pump of capacity 15hp 20 hp for comprerhensive maintenance and if required taking out burnout old winding from the stator , lowering complete the non clogging pumping set and reflixing the motor carefully including connection and testing , pumping out sewage water from the existing sumps tanks of stps mbbr technology with the help of non clogging , cleaning of 1.2 mld sewage treatment plant after pumping out sewage water from the existing sumps , lifting the non clogging submersible pump set electrically operated by 3.7 hp 3 phase motor incl column pipe line , dismantling of non clogging submersible pump of capacity 3.7 hp and taking out burnout winding from the stator of motor and rewinding with pvc copper wire , dismantling of electric sewage induction motor 3.0 hp ac 3 phase 415 volts from site after disconnecting from pump , dismantling non clogging pump set of centrifugal type 3.0 hp induction motor ac 3 phase 415 volts , dismantling of electric induction blower motor 5.0 hp ac 3 phase 415 volts for comprehensive maintenance from site after disconnecting , dismantling of electric induction blower motor 30.0 hp ac 3 phase 415 volts for comprehensive maintenace from site after disconnecting from blower electric connection , material and labour for pcc 1 3 6 type c2 using 40mm graded stone aggregate for foundation etc , m and l for taking out comprehensive maintenance of existing unserviceable air blower of any make of capacity 125 cubic hr to 188 cubic hr with taking out of electric cable , supply only gear oil ep 90 complete all as specified and as directed by engineer in charge. , supply only air filter suitable for existing one complete all as specified and as directed by engineer in charge. , supply only belt as per existing model complete all as specified and as directed by engineer in charge. , supply only bearing as per existing complete all as specified and as directed by engineer in charge. , supply only set of rotor with hub as per existing model complete all as specified and as directed by engineer in charge. , m and l for finding out defect of stps panel and taking out burnt interconnection wiring including u.s and serviceable component for re use including rewiring of panel , supply and fix in repairs flexible flat pvc copper couductor stranded submersible cable cores 1100 volt grade 4 sqmm 3 bid details/ 2 / 41 core , supply and fix in repairs flexible flat pvc insulated pvc couductor stranded submersible cable cores 1100 volt grade 10 sqmm 3 core , s and f round strand steel wire rope dia 12 mm and connected clamp nut bolts fixed complete all as specified and as directed by engineer in charge. , s and f submersible pump ful

Water Vapor Cryotraps Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

Central Government/Public Sector

State Government

State Government