Latest weigh batcher Tenders | Government weigh batcher Tenders

CTN :45720895

01 Jul, 2026 25.00 Lacs

Pali - Rajasthan

Tender For annual rate contract for annual maintenance and spare parts supply work of jcb machines. - cylinder liner, over haul gas kit, valve inlet exhaust, crank shaft, main bearing set, trust washer, piston, piston ring set, diesel main pipe, diesel filter pipe, thermo state elbow, air cleaner hose, diesel pump repair with parts, thermo state valve, connecting rod, con. rod bearing set, cam shaft bush, rocker arm, rocer arm shaft, gear cam shaft, water pump assy., oil pump assy., oil filter, belt, engine mount pad, exhaust elbow, engine throttle cable, engine stop cable, turbo charger assy., silencer exhaust abi, flang exhaust, element main, element secondary, auto tensioner, idler gear, engine fan, fuel filter assy., filter kit, engine connecting rod, fan drive puley, hyd. strainer, suction strainer, fuel injection pump, injector pipe, rubber hose, fuel filter assy., nozzle, return line, fuel module with sensor, fuel tank cap, fip repair with parts, radiator, radiator assy., coolent, hose top, hose cac (cold side), hose cac (hot side), radiator solding, front grill, front grill lock, front wheel and axle, axle service, center pin, axle stub, hub, hub stud, hub seal, seal cone, bearing inner, bearing outer, axle carrior l/h, axle carrior r/h, track rod, brake fri. plate, brake cou. plate, brake seal, brake oil 500ml, differential, differential gear planet, gear planet, bearing roller double, seal cassetle, bearing teper, tripling seal, stud wheel, carrior innulus, gear innulus ring, hub palentry, drive shaft, bearing roller, bearing teper roller, yoke, cross patti & bolt, cross holder, uj cross, bearing, brake, master brake cylinder, pipe brake l/h, pipe brake r/h, brake reserver, steering, coupling, bearing, rim steering wheel, self starter, self starter, solenoid, switch altinator, altinator puley, wheel belt 1232, rocker plate, field set, armature bush set, bearing assy., carbon set, bendex, armature, armature bush set, altenator, starter, cut out, rectifier plate, bearing, bearing plate, rotor, terminal, wiring and electrical, wiring harness complete, bettery cable, hour meter, head light bulb, tail light bulb, fuse and reley 15 amp, tail lamp, head light assy., ignition switch, wiper blade assy., harness roof, combination switch, fog lamp, body, side mirror, seat, wiper motor assy., wiper blade, catch window, latch l/h, wind screen front, glass outer l/h, glass outer r/h, rear window glass, door soccker, door hinge, lock set inner, lock set outer, door got set, door belt, transmission, transmission over, charging pump assy., counter plate, firction plate, transmission filter, bearing, bearing, torque converter, bearing, converter, drive plate kit, mounting, yoke coupling, lever assy. gea turret, selonoid valve assy., strainer, transmission filter, stabliser, steblizer piston, steblizer rod, inner leg steblizer, steblizer foot, pin pivot, adjuster, atb rear pad kit lower, atb rear pad kit upper, hydraulic, ind. steering suct, selonoid coil, hyd. filter assy., hyd. filter element, mrv, hyd. pump, repair kit, priority valve, ram seal, pump seal kit, pump steering, ramp bucket, ramp bucket, ramp bucket, ram, bucket lift cylinder ram, bucket tilt cylinder ram, boom ram, loader ram, loader jaw ram, dipper ram, slew cylinder ram, stablizer ram, steering cylinder ram, 6 in 1 ram, hose, hose-10-bsp 560mm, hose-08-bsp 1860mm, hose-10-bsp 2750mm, hose-04-10bsp 1825mm, hose-08-bsp 2620mm, hose-10-bsp 2520mm, hose-08-bsp 2860mm, hose-08-bsp 2650mm, hose-12-bsp 3900mm, pin and bush, bucket pin, pin, pin, tipping lever, pin dipper, bush, bush, pin, boom main pin, pin, pin top, pin pivot, pin pivot, pin boom ram, pin pivot, pin pivot, pin pivot, kpc kit and bush, bucket kit, seal kit, bucket seal kit, dipper seal kit, boom seal kit, seal slew kit, s t b, steering seal kit, loader seal kit, lift seal kit, bucket seal kit, rubber seal kit, boom seal kit, s t b kit, slew seal kit, loader seal kit, steering seal kit, loader and bucket welding, l

CTN :45609414

01 Aug, 2026 NA

Rampur-Up - Uttar Pradesh

Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - industry unit; hardware items; as per tender document - utting wheel age , polish wheel aga , lirinding wheel a-size-5 , cutting wheel-ags , emery paper fine , umery paper rough , welding white glass , emery paste fine-400 gm , emery paste rough-400 gm , heavy duty hand wire brush with handle size-12" long , anahond 606 , holdite compound 500 gm pack , cotton waste coloured good quality , painting brush , painting brush 4 , hacksaw blade size-12"x 12" , brasso 500 ml , restoline 500 ml , split pin wax2" , split pin size 3/16" x 15 , loctite 641 , heavy duty hand gloves (pair) , welding hand screen , oxygen regulator , gas cutting nozzle 1/16 , gas cutting nozzel 1/32" , gas cutting nozzle 1/64 inch , wleding alluminum cable 600 amp 95mm , rubber hose pipe red pressure 1250 psi , rubber hose pipe blue pressure 1250 pse , welding holder 1000 amp , gas cutting torch , grinding wheel agi , welding black glass , measuring tape 3 mtr , emery tape rough, size-2" (30mtr roll)

State Government

CTN :45581468

22 Jun, 2026 1.00 Lacs

Nagaur - Rajasthan

Tender For विधुत व्यवस्था एवं विद्युत उपकरण मरम्मत कार्य - electrical system and electrical equipment repair work- philips led bulb 20w , door bell electric, , fan repairing charges, , ac service charges, , ac gas refilling, , ac capacitor, , ac blower motor, , water motor repairing, , tube light philips, , wire per feet 2.5, 1.5, 1, , switch, , fan capacitor, , regulator, , shri pin holder, , two pin holder, , watch electric digital, , watch simple oreva, , extension board 4 switch wire 30 feet, , extension board 6 switch wire 30 feet, , street light new purchase, , street light repair, , ceiling light up to 20 watts, , ceiling light 2 by 2, , stabilizer (for ac)

CTN :45499744

24 Jun, 2026 27.12 Lacs

Ongole - Andhra Pradesh

Tender For providing developmental works in torragudipadu g.p of chimakurthy mandal package 5 works - scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per technical specification clause 301.4. mord , construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 mord , construction of sub grade with quarry waste(table 400.13) by mix in place method normal construction of granular sub base by providing quarry waste material spreading in uniform layers with motor graded on prepared surfce mixing by mix in place method with rotavator at once and compacting with vibratory roller 80-100 kn r to achive the desired density complete as per clause 401.4 as per technical specification clause 408 mord , construction of granular sub-base by providing well graded hbg material (grading iii material) (table 400.2) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller 80-100 kn / vibratory roller to achieve the desired density, complete as per technical specification clause 402 mord including cost of all materials, labour, conveyance, hire charges of machinary, royalties, all taxes etc complete as per direction of engineer in charge.1 , including over head but excluding seignorage charges and gst desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. , clearing juliflora (prosafis) jungle including up-rooting and removing of juliflora stumps. etc complete. ssr from road & bridge works rates of materials & work items ..112(d) of current ssr (2025-26). mat-00482

CTN :45499755

24 Jun, 2026 17.88 Lacs

Ongole - Andhra Pradesh

Tender For providing developmental works in yerragudipadu (v) & g.p chimakurthy mandal package 2 (3 works) - scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per technical specification clause 301.4. mord. , construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 mord , construction of sub grade with quarry waste(table 400.13) by mix in place method normal construction of granular sub base by providing quarry waste material spreading in uniform layers with motor graded on prepared surfce mixing by mix in place method with rotavator at once and compacting with vibratory roller 80-100 kn r to achive the desired density complete as per clause 401.4 as per technical specification clause 408 mord , construction of granular sub-base by providing well graded hbg material (grading iii material) (table 400.2) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller 80-100 kn / vibratory roller to achieve the desired density, complete as per technical specification clause 402 mord including cost of all materials, labour, conveyance, hire charges of machinary, royalties, all taxes etc complete as per direction of engineer in charge.1 , including over head but excluding seignorage charges and gst desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. , clearing juliflora (prosafis) jungle including up-rooting and removing of juliflora stumps. etc complete. ssr from road & bridge works rates of materials & work items ..112(d) of current ssr (2025-26). mat-00482

CTN :45499760

24 Jun, 2026 27.45 Lacs

Ongole - Andhra Pradesh

Tender For providing developmental works in yelurivaripalem (v) of chimkaurthy mandal package (4 works) - shoulders are filling the selected earth for levelling the site as per drawing and technical specification clause 305.3.9 mord & 304 morth but excluding gst & seigniorage charges. for shoulders. , scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per technical specification clause 301.4. mord , earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per technical specification 305 mord / 304 morth , construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 mord , construction of granular sub-base by providing well graded hbg material (grading iii material) (table 400.2) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller 80-100 kn / vibratory roller to achieve the desired density, complete as per technical specification clause 402 mord including cost of all materials, labour, conveyance, hire charges of machinary, royalties, all taxes etc complete as per direction of engineer in charge.1 , including over head but excluding seignorage charges and gst desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges.

CTN :45499768

24 Jun, 2026 17.53 Lacs

Ongole - Andhra Pradesh

Tender For providing developmental works in pulikonda (v) of chimkaurthy mandal package 1 (3 works) - scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per technical specification clause 301.4. mord , construction of granular sub-base by providing well graded hbg material (grading iii material) (table 400.2) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller 80-100 kn / vibratory roller to achieve the desired density, complete as per technical specification clause 402 mord including cost of all materials, labour, conveyance, hire charges of machinary, royalties, all taxes etc complete as per direction of engineer in charge.1 , including over head but excluding seignorage charges and gst desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. , construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 mord , shoulders are filling the selected earth for levelling the site as per drawing and technical specification clause 305.3.9 mord & 304 morth but excluding gst & seigniorage charges. for shoulders.

CTN :45499769

24 Jun, 2026 17.57 Lacs

Ongole - Andhra Pradesh

Tender For providing developmental works in pulikonda (v) of chimkaurthy mandal package 2 (3 works.) - scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per technical specification clause 301.4. mord, construction of granular sub-base by providing well graded hbg material (grading iii material) (table 400.2) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller 80-100 kn / vibratory roller to achieve the desired density, complete as per technical specification clause 402 mord including cost of all materials, labour, conveyance, hire charges of machinary, royalties, all taxes etc complete as per direction of engineer in charge.1 , including over head but excluding seignorage charges and gst desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges., construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 mord, shoulders are filling the selected earth for levelling the site as per drawing and technical specification clause 305.3.9 mord & 304 morth but excluding gst & seigniorage charges. for shoulders., earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per technical specification 305 mord / 304 morth

CTN :45499776

24 Jun, 2026 20.60 Lacs

Ongole - Andhra Pradesh

Tender For providing developmental works in rangasaipuram village gadiparthivaripalem gp of chimakurthy (m) package 1 (4 works) - construction of granular sub-base by providing well graded hbg material (grading iii material) (table 400.2) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller 80-100 kn / vibratory roller to achieve the desired density, complete as per technical specification clause 402 mord including cost of all materials, labour, conveyance, hire charges of machinary, royalties, all taxes etc complete as per direction of engineer in charge.1 , including over head but excluding seignorage charges and gst desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. , construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 mord , earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per technical specification 305 mord / 304 morth . scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per technical specification clause 301.4. mord . shoulders are filling the selected earth for levelling the site as per drawing and technical specification clause 305.3.9 mord & 304 morth but excluding gst & seigniorage charges. for shoulders.

CTN :45499777

24 Jun, 2026 13.75 Lacs

Ongole - Andhra Pradesh

Tender For providing developmental works in rangasaipuram village gadiparthivaripalem gp of chimakurthy (m) package 2 (3 works) - shoulders are filling the selected earth for levelling the site as per drawing and technical specification clause 305.3.9 mord & 304 morth but excluding gst & seigniorage charges. for shoulders. , scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per technical specification clause 301.4. mord , earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per technical specification 305 mord / 304 morth , construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 mord , construction of granular sub-base by providing well graded hbg material (grading iii material) (table 400.2) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller 80-100 kn / vibratory roller to achieve the desired density, complete as per technical specification clause 402 mord including cost of all materials, labour, conveyance, hire charges of machinary, royalties, all taxes etc complete as per direction of engineer in charge.1 , including over head but excluding seignorage charges and gst desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges. desired density, complete as per technical specification clause 401 mord / morth. but excluding vat & seigniorage charges.

Weigh Batcher Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government