Latest wheel set Tenders | Government wheel set Tenders

Central Government/Public Sector

CTN :43171204

03 Jan, 2026 NA

Guna - Madhya Pradesh

Tender For supply of fenner make taper lock bush; designation: 2012,fenner make taper lock bush; with id: 38h7 & a keyway of 10mm width and 3.3mm depth; designation,fenner make duplex chain wheel sprocket (pinion) , pitch: 1/2" , no. of teeth: 38 t, designation: 42-,fenner make chain wheel sprocket (pinion) ; pitch: 1/2" inch, no. of teeth: 21t

CTN :43171366

23 Dec, 2025 NA

Jammu - Jammu And Kashmir

Tender For supply of speedo meter assy,cap camp fuel filter,speedo gear,front fork oil seal,speedo cable,winker switch,frt brake cable,brake shoe frt,brake shoe rear,gasket and reservor,flap set rear,assy master cyl,generator assy,lock nut,brake fluid container,pipe brake no 6,traficator assy frt,speed sensor,pull and push switch,assy oil filter,cover assy,clutch release brg,pipe,chain sprocket kit,brake shoe rear,sleeve rr wheel,disc clutch friction,clutch center holder,arm assy kick starter,weather strip,oil filter,oil filter,rear door lock,oil seal extension case,bearing

CTN :43153199

22 Dec, 2025 NA

Ranga Reddy-T - Telangana

Tender For supply of five chamber tail lamp 24v lh , five chamber tail lamp 24v rh , tail light assy rh , clutch release brg , assy fly wheel ring , field coil auxiliary , dist piece , major repair kit air compressor , air compressor repair kit , bearing bush , bush king pin , assy cable set , chain sprocket kit , cyl assy brake master , arm foot rest rh , arm foot rest lh , bearing assy front

CTN :43153141

24 Dec, 2025 NA

Tinsukia - Assam

Tender For supply of mt sapare c c - bendix drive for tata , fly whel assy for tata , fog light for tata , wheel brg for tata safari , chain sprocket set for hero honda , speedometer cable for hero honda , spark plug for hero honda , sleeve cyl assy for tata

CTN :43146571

22 Dec, 2025 NA

Tinsukia - Assam

Tender For supply of mt spares c c - cylinder kit , timing chain , gasket all , valve set , oil seal gasket , wheel brg , sprocket brg , brake shoe rear , brake shoe front , suspension kit , fuel filter , oil filter , gear lever assy , kit lined shoe , disk brake , wiper blade , regulator , oil pressure switch

Central Government/Public Sector

CTN :42606016

29 Dec, 2025 NA

Goa - Goa

Tender For corrigendum : supply of magnetic compass - ta sl no 4 1 1 1 transmitting type magnetic compass with electrical transmission , ta sl no 4 1 1 2 magnetic compass binnacle , ta sl no 4 1 1 3 rim ring with two bearings mounted , ta sl no 4 1 1 4 hood without aperture with handles , ta sl no 4 1 1 5 main electric light with suitable cable type of 3 1 5 sq , ta sl no 4 1 1 6 emergency electric light with suitable cable type of 3 1 5 sq , ta sl no 4 1 1 7 junction box with 5 pole terminal strip for compass light , ta sl no 4 1 1 8 fastening material comprising of 4 bolts of brass m16 4 washers and 4 nuts with flange , ta sl no 4 1 1 9 1 lenses and mounting individually adjusted to an optimum value according to the length of thr reflection tube , ta sl no 4 1 1 9 2 reflection tube 140mm dia with flange one gasket , ta sl no 4 1 1 9 3 removable flange to seal the hole in the deck or ceiling from below , ta sl no 4 1 1 9 4 locking device for the telesc opic mirror head wheel house unit , ta sl no 4 1 1 9 5 wheelhouse unit with day and night mirror , ta sl no 4 1 1 10 six bar magnets 200 mm long 10 mm dia for b c correction , ta sl no 4 1 1 11 two full size d spheres of soft iron with marking fastening bolts m16 with washers and nuts of brass , ta sl no 4 1 1 12 one heeling magnet in tube with marked chain active length 175 mm one magnet 125mm one magnet 50 mrn long , ta sl no 4 1 1 13 reflector compass with compass card dia 180 mm with directional system , ta sl no 4 1 1 14 standard azimuth device with vanes and black hinged mirror , ta sl no 4 1 1 15 1 brackets of coated brass with fastening bolts nuts and washers , ta sl no 4 1 1 15 2 flinders tube brass , ta sl no 4 1 1 15 3 plastic cover for flinders tube , ta sl no 4 1 1 15 4 soft iron core 305 mm length , ta sl no 4 1 1 15 5 soft iron core 152 mm length , ta sl no 4 1 1 15 6 soft iron core 76 mm length , ta sl no 4 1 1 15 7 soft iron core 38 mm length , ta sl no 4 1 1 15 8 wooden core 280mm length , ta sl no 4 1 1 15 9 wooden core 140mm length , ta sl no 4 1 1 15 10 wooden core 70mm length , ta sl no 4 1 1 15 11 wooden core 35mm length , ta sl no 4 1 1 16 magnetic compass repeaters , ta sl no 4 1 1 17 junction box converter box other accessories including cables required for interfacing with ships degaussing system , ta sl no 4 1 1 18 nmea booster splitter convertors for transmission of heading information , ta sl no 4 1 1 19 interconnecting cables , ta sl no 4 1 1 20 interface resistor box attenuator for interfacing with rs degaussing system , ta sl no 4 1 1 21 proving of the interface between rs degaussing system and magnetic compass during hats and sats , ta sl no 4 1 6 on board spares , ta sl no 4 1 3 and 5 14 services of engineers and training , ta sl no 4 1 4 and 5 13 12 drawings and documentation

Corporations And Associations And Others

CTN :43133812

17 Dec, 2025 2.98 Lacs

Delhi - Delhi

Tender For supply of machinery/tools for various parks at sarita vihar in ward no. 187, central zone - brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cutting attachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight( dry,without cutting attachment & deflector): should not be more than 7.5 kgclutch: centrifugal type, clutch shoe support base & lining metal only.multi function handle: should have acceleration ,on/off switch at right handle.brushcutter harness: should be double shoulder harness only.anti vibration system: must have 4- point aniti vibration system.vibration level in m/s2 at right handle : should not be more than 2.5 m/s2sound pressure level db(a): should not be more than 105 db(a)drive shaft design: must have drive shaft ends square design type only.certification : must have valid en certificaton, petrol operated chain sawengine : single cylinder, 2 stroke, aircooled onlydisplacement: 45.4ccpower output : 2.3kw. 3.0 hp max.engine speed (with guide bar & chain ): at least 12500 rpmcarburetor: diaphragm type & compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight( without cutting attachment ): should not be more than 5.0 kgclutch: clutch shoe linining metal only.guide bar design: should be rollomatic type.guide bar length: guide bar length must have 50 cm/20" inch. guide bar and chain: should have same manufacture only.chain type: every drive link require groove & small oil receiver hole for better lubrication. 0.325 inch pitch & 1.6 mm thickness only.chain lubrication system: fully automatic ,speed controlled rotary oil pumpchain oil tank capacity: should be minimum 200 ml.oil pump drive: should have direct drive from crankshaft & oil pump flow adjustable.master lever control: must have all operation in one hand, chock,throttle, acceleration,switch off.guaranteed sound power level: should not be more than115 db(a)maximum chain velocity to iso 11681: should be minimum 28 m/scertification: product should have valid dplf certificate with test standard en iso 11681., tree prunersupply of telescopic pole pruner:-specification:- pole length incuding blade: 6.5m blade material: hardened & tempered high carbon steel .the head of the blade shall have a hooked tip useful for cutting twigs saw blade shape: hooked type curved saw blade type & no of cutting teeth :tripple grounded 86 teeth blade length : 15"-16" pole type: light weight telescopic tubular aluminium alloy extendable pole no of positions for pole height adjustment : 10 positions locking mechanism : ergonomicvally designed two way locking mechanism total working length : max 219"(6623 mm), min 103" (3103mm) branch cutting capacity: 200mm max, lawn mowersupply of lawn mower:-specification:- type of machine walk behind lawn mowerspower source petrol enginestart type recoil / pull startspeed control variable speeddrive type all wheel driveblade style rotary typeblade engagement electromagneticcut width (mm) 500 to 524minimum cut height 1 millimetermaximum cut height 26 millimeterblades metallicnumber of blades 1number of positions for cut - height adjustment 2number of levers for cut - height adjustment single levernumber of wheels 4front wheel size 200 millimeterrear wheel size 200 millimeterwheel tyres pneumaticif yes, grass catcher / collector / bag volume 88 liter"engine power rating (watt)" 4000 to 4999engine fuel tank capacity - 1 ltr., lopperanvil tree branch lopper lade material - high carbon steel with hard surface treatment, overall length - not less than 914 mm handle material - similar materil as per requirement, weight - 1.5 kg., cutting dia - not less than 38mm

Central Government/Public Sector

CTN :43141058

31 Dec, 2025 NA

Gandhinagar - Gujarat

Tender For supply of combination spanner (mm) 6mm-32 mm , combination spanner (inch) 1/4" to 1 1/4" , adjustable wrench 8" , heavy duty pipe wrench 24" , screw driver set 6" to 12" , allen key set ( mm) , allen key set (inches) , combination plier 8" , long nose plier 160mm , circlip plier ( bent external) 9" , circlip plier ( straight internal) 9" , circlip plier ( straight external) , 22 pc 1/2" socket set , bolt cutter tubular handle 36" , 200 mm 2nd cut flat file , 200 mm 2nd cut round file , 200 mm 2nd cut half round file , 200 mm 2nd cut traingle file , drilling hammer , ball pein hammmer -12 oz - 2 lbs , mason chisel 1-3/4 x 8-1/2 , 5 tray metal tool box , aluminium pipe wrench 18" , chain wrench 24" , 1/8" -2" pipe cutter , chain pipe vice 1/8" to 4" , spare cutting wheel for cutter - blade , circlip plier ( bent internal) 9" , metal hacksaw frame 12" , metal hacksaw blade 12" , water pump plier 12"

CTN :43162497

22 Dec, 2025 NA

Pune - Maharashtra

Tender For supply of spark plug,speedometer cable,coil ignition,fuel filter mpfi,gear lever kit,sleeve cyl assy,wheel cyl assy,clutch plate,pressure plate,bearing tapper roller bearing,synchronizer ring,needle bearing,regulator sr40,ram service kit,cabin lifting pump,chain 84l,shoe comp brake,accelerator assy,air cleaner element,oil filter,wiper blade,assy fuel filter,pre fuel filter,alternator belt,ac belt

CTN :43147228

17 Dec, 2025 NA

Parganas - West Bengal

Tender For supply of spare parts for scania veh - connector part no 232550, quick release valve part no 189568, connector part no 140537, tee-connector part no 225448, relay valve (with doub. check valve) part no 215621, elbow connector part no 146235, elbow connector part no 171170, cross connector part no 229030, socket front part no 161070, piston pair/par part no 271344, valve part no 161078, cam follower part no 262316, body part no 173806, o ring part no 160422(5331000052), spring seat part no 141810, inlet, exhaust valve part no 229373, filter part no 2940004958(230672), repair kit part no 263664, repair kit part no 263667, nozzle part no 2640000265(337857), running board right part no 249730, bolt with chain part no 255240, wheel angle indicator part no 217669, sliding contact part no 130770, cap lower part part no 1102372

Wheel Set Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

Corporations And Associations And Others

Central Government/Public Sector