Latest winch gear box repair Tenders | Government winch gear box repair Tenders

State Government

CTN :45275642

02 Jun, 2026 3.07 Lacs

Serampore - West Bengal

Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging

Central Government/Public Sector

CTN :44980530

08 Jun, 2026 NA

Mumbai - Maharashtra

Tender For supply of set of spares for train 18 gear box,one set consisting of 35 items as per attached annexure a.make: medha [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :45030365

29 May, 2026 NA

Cuddapah - Andhra Pradesh

Tender For supply of bonfigloli gear box spares on annual rate contract basis - model-1:model: as55 df p112, code: 1900000950717270002, batch:6/19, v1, i:33:2, application : i) neutralization tank agitator ii) precipitation tanks in chemical house iii) causticization tanks, casing with flange (part no. 2) for model-1, cover (part no. 3) for model-1, internal support (part no. 4) for model-1, gasket (part no. 5) for model-1, gasket (part no. 6) for model-1, extended 1st reduced pinion (part no. 7) for model-1, bored 1st reduced pinion (part no. 8) for model-1, gear wheel 1st reduction (part no. 9) for model-1, gear wheel 2nd reduction (part no. 10) for model-1, pinion 3rd reduction (part no. 11) for model-1, gear wheel (part no. 12) for model-1, cap (part no. 13) for model-1, bored input shaft (part no. 14) for model-1, oil seal (part no. 15) for model-1, oil seal (part no. 16) for model-1, gear head / box, in put assembly, out put assembly, bearing (part no. 20) for model-1, bearing (part no. 21) for model-1, bearing (part no. 22) for model-1, bearing (part no. 23) for model-1, bearing (part no. 24) for model-1, key (part no. 25) for model-1, key (part no. 26) for model-1, key (part no. 27) for model-1, key (part no. 28) for model-1, key (part no. 29) for model-1, level plug (part no. 30) for model-1, drain plug (part no. 31) for model-1, breather plug (part no. 32) for model-1, parallel pin (part no. 33) for model-1, parallel pin (part no. 34) for model-1, hex head screw (part no. 35) for model-1, hex head screw (part no. 36) for model-1, hex head screw (part no. 37) for model-1, circlip (part no. 38) for model-1, circlip (part no. 41) for model-1, circlip (part no. 42) for model-1, 2 nd reduction pinioin (part no. 45) for model-1, out put shaft (part no. 47) for model-1, spacer ring (part no. 48) for model-1, circlip (part no. 58) for model-1, circlip (part no. 39) for model-1, extended input shaft (part no. 50) for model-1, key (part no. 51) for model-1, input assembly, output assembly, model-2:as60 df p112, code: i 11799930001,batch:4/10, v1, i:37:1, application : feed tank agitator - ssr, casing with flange (part no. 2) for model-2, cover (part no. 3) for model-2, internal support (part no. 4) for model-2, gasket (part no. 5) for model-2, gasket (part no. 6) for model-2, extended 1st reduced pinion (part no. 7) for model-2, bored 1st reduced pinion (part no. 8) for model-2, gear wheel 1st reduction (part no. 9) for model-2, gear wheel 2nd reduction (part no. 10) for model-2, pinion 3rd reduction (part no. 11) for model-2, gear wheel (part no. 12) for model-2, cap (part no. 13) for model-2, bored input shaft (part no. 14) for model-2, oil seal (part no. 15) for model-2, oil seal (part no. 16) for model-2, gear head / box, in put assembly, out put assembly, bearing (part no. 20) for model-2, bearing (part no. 21) for model-2, bearing (part no. 22) for model-2, bearing (part no. 23) for model-2, bearing (part no. 24) for model-2, key (part no. 25) for model-2, key (part no. 26) for model-2, key (part no. 27) for model-2, key (part no. 28) for model-2, key (part no. 29) for model-2, level plug (part no. 30) for model-2, drain plug (part no. 31) for model-2, breather plug (part no. 32) for model-2, parallel pin (part no. 33) for model-2, parallel pin (part no. 34) for model-2, hex head screw (part no. 35) for model-2, hex head screw (part no. 36) for model-2, hex head screw (part no. 37) for model-2, circlip (part no. 38) for model-2, circlip (part no. 41) for model-2, circlip (part no. 42) for model-2, 2 nd reduction pinioin (part no. 45) for model-2, circlip (part no. 58) for model-2, circlip (part no. 39) for model-2, extended input shaft (part no. 50) for model-2, key (part no. 51) for model-2, spacer ring (part no. 46) for model-2, out put shaft (part no. 49) for model-2, circlip (part no. 57) for model-2, input assembly, output assembly, model-3:as60 df p132, code:i11800030001, batch:4/10, v1, i:33:4,application : i) filtrate tank

State Government

CTN :45007424

26 May, 2026 1.49 Crore

East Nimar - Madhya Pradesh

Tender For corrigendum : complete overhauling of electrical wire rope hoist along with supply of spares for electrical wire rope hoist installed at coal mill area at 2x600 mw, stage-i, sstpp, mppgcl, dongalia. - scope of service, complete supervision & installation of new spares/replacement of damaged/eroded spares of all 08 numbers of hoist (04 numbers capacity-20 ton & 4 numbers of capacity-15ton)., scope of supply, spares for 20 ton hoist, brake motor 15hpx1000rpm, 40% cdf, 150st/hr, s4 duty, foot mounted sq cage f/s 160 l, terminal box required right side for 15t or 20t hoist make : siemens, brake motor 1.5hpx1000rpm, 40% cdf, 150st/hr, s4 duty, flange mounted sq cage f/s 90 s for ct<, terminal box required top side make : siemens, gear box with coupling for trolley, mdl: ibc162/25.9/200-24 make: premium, gear box with coupling for trolley, mdl: ibc162/18.9/200-24 make: premium, rotary limit switch make: soc, two way lever type limit switch, make: soc, disc brake for 15hp motor, make: - emco, type 14.458, size: - 20, disc brake for 1.5hp motor, make: - emco, type 14.458, size: - 12, cable trolleys medium duty, wheel dia min 40 mm., wire rope 20 mm / 6x36 steel core/ galvanized, make- ushamartin, push buttons with 12 meter cable, rectifier size- eh720hhd, long travel dsl system, i- chain (5 mm)-, ii- cable 6 mm epr, iii- fasteners (1/4x2 ), lt motor shaft, lt motor pinion, spares list of 15-ton hoist, brake motor 15hpx1000rpm, 40% cdf, 150st/hr, s4,duty, foot mounted sq cage f/s 160 l, terminal box required right side for 15t or 20t hoist make : siemens, brake motor 1.5hpx1000rpm, 40% cdf, 150st/hr, s4 duty, flange mounted sq cage f/s 90 s for ct, terminal box required top side make : siemens, gear box with coupling for trolley, mdl: ibc162/25.9/200-24 make: premium, gear box with coupling for trolley, mdl: ibc162/18.9/200-24 make: premium, rotary limit switch make: soc, two way lever type limit switch, make: soc, disc brake for 15hp motor, make: - emco, type 14.458, size: - 18, disc brake for 1.5hp motor, make: - emco, type 14.458, size: - 12, cable trolleys medium duty, wheel dia min 40 mm., wire rope 15 mm / 6x36 steel core/ galvanized, make- ushamartin, pendent push buttons, rectifier size- eh720hhd, long travel dsl system, chain (5 mm)-, cable 6 mm epr, fasteners (1/4x2 ), lt motor shaft, lt motor pinion

Central Government/Public Sector

CTN :45311501

27 May, 2026 NA

Karimnagar - Telangana

Tender For supply of bevel gear spares for coal mills of ntpc ramagundam stage 1

Central Government/Public Sector

CTN :45069836

28 May, 2026 NA

Korba - Chhattisgarh

Tender For corrigendum : procurement of spares of piv gearbox for st ii scrapper conveyor ahd ntpc korba - overload coupling,piv,mrhb43, brake band,piv,gear box,mrhb43

State Government

CTN :45287297

11 Jun, 2026 NA

Chandrapur - Maharashtra

Tender For procurement of drive mechanism spares required for air preheater of u#3 boiler during coh at cstps, chandrapur. - blr regah 0 0 bibby coupling: 124a, blr regah 0 0 bibby coupling: 124c, regen aph 5 apc speed reducer brg set, blr regah 0 0 fluid coupling fcu: 11.5, blr regah 0 0 fusible plug, blr regah 0 0 multidisc plate, blr regah 0 0 nut bolt set for coupling, blr regah 0 0 resilient plate, blr regah 0 0 input shft for gearbox, reg aph 2nd stage pinion shaft, reg aph spiral bevel pinion shaft, reg aph spiral bevel gear, reg aph low speed shaft, reg aph 1st stage pinion shaft, taper lock bush for 5apc main drive gear

State Government

CTN :45287473

28 May, 2026 NA

Chandrapur - Maharashtra

Tender For procurement of spares of bottom ash hopper feed gate, hydro ejectors and liners for clinker grinder during u#8 aoh at ash handling plant cstps, chandrapur. - 85tph liner pn be1440d-01, 85tph liner pn be1440d-02, feeder ejector ayems inlet liners, slight glass assly size-3/4" n3922, hopper driplex inspection glass 220 mm, macawber beekay gland follower, bearing cover (1 set = 4 nos.) be1435d, bearing block (1 set = 4 nos.)be1434d, spur gear be1437d, shaft stuffing block be1431d, gate liner for door frame thick 24 mm, gate liner thickness 14 mm, fed gate side guide plate pn be5064d, fed gate flood light assly be3749d-02, complete feed sump assembly with liner, throat & discharge piece(be 3261d-03), fed gate bracket,pin &piston rod clevis, feed gate cylinder assy pn be4865d, feed gate tecpro sys power cyl seal set, ahp basys fdgate guide rail, fed gate lower wedge be1121d-b, fed gate upper wedge be1121d-a

State Government

CTN :45272693

11 Jun, 2026 NA

Chandrapur - Maharashtra

Tender For procurement of gearbox and it s spares for clinker grinders in ahp-210mw during u-3 coh at cstps, chandrapur. - ahp basys cg gear box, ahp basys cg gear box spares set, coupl flexible element (part no-36), fluid sm 4 coupling half for gear box si

Central Government/Public Sector

CTN :45197721

30 May, 2026 NA

Bhilai - Chhattisgarh

Tender For corrigendum : tender for supply of spares for caterpillar track type loader -panel as control 416 dash 4641 caterpillar , carrier as p no 327 dash 7127 caterpiller , idler as p no 7t3501 , hub sprocket pn 317 dash 0680 caterpillar , harness as engine 304 dash 5166 caterpillar , motor gp gear pn 456 dash 4197 caterpillar , motor gp gear pn 307 dash 3175 caterpillar

Winch Gear Box Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors