Get complete information related to latest Wiper Rubber Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Wiper Rubber Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Wiper Rubber Tenders.
Tender For corrigendum : supply of elevator ece cch256 door bottom shoes , elevator ece cch256 ecm121 control card , elevator ece transformer 690v , elevator ece smps 24v , elevator ece pcb bmo , elevator ece door drive motor , elevator ece v3f drive to door , elevator ece ecm121 arl 300 , elevator ece car display 7 segme , elevator ece landing display 7 s , elevator ece ir screen , elevator ece open belt car door , elevator ece cch256 car guide shue 16mm- , elevator ece pgb2 card , elevator ece g7a403 vvvf unit-30kw g7-4 , elevator ece make brake resistance 35r , elevator ece make ard set automatic r , elevator ece make over load device , elevator ece make cabin header - c4 pa
Tender For supply of 2.2 kw ac crane drive , 5.5 kw ac crane drive , 11.0 kw ac crane drive , 22.0 kw ac crane drive , 37.0 kw ac crane drive , 55.0 kw ac crane drive , 75.0 kw ac crane drive 3 phase, digital ac crane drive 2.2 kw, ac drive should be suitable for heavy duty operation of 2.2 kw. offered ac drive should be suitable for crane-hoist operation. if, separate software required for crane application, it must be clubbed with supply of material. ac input voltage: 380 to 480v ac 10%, 3 phase, 3 wire, 50 hz; mode of control: bi-directional fully controlled 3-phase ac; speed regulation: 1% of base speed; braking: suitable dynamic braking resistance and chopper unit (external or in-built); acceleration time: 0.1 to 1000s or better; deacceleration time: 0.1 to 1000s or better; overload: 150%-1min, 200%-3.0s; ambient temperature: 0 to 50 c (derating shall not occur below 50 c. in the event that derating occurs below 50 c, the supplier shall provide a higher-rated drive to match the requirement); rated current at 50 c: min. current should be 5.5 amps at 50 c; high starting torque at low speed: 200% starting torque at 0.3 hz; two analog inputs: two nos. analog inputs having signal voltages of 0 to 10 vdc or 4 to 20 ma (configurable); two analog outputs: two nos. analog outputs having signal voltages of 0 to +/-10 vdc or 4 to 20 ma (configurable); six digital inputs: pnp/npn; one relay output: with short-circuit and overload protection; two digital outputs: with short- circuit and overload protection; brake release signals: outputs braking signals based on inverter operating conditions to prevent cargo bed rollback and overrunning; load adaptive control: when the actual load level is lower than the configured load level, the system can be operated at a ratio-multiplied speed (in terms of the configured frequency), resulting in significantly better efficiency; load ) /bid number : gem/2026/b/7563714 * /dated: 20-05-2026 & & / bid document 1 / 29 frequency), resulting in significantly better efficiency; load limiter: maintains the safety and rescuability of suspended loads by stopping when excessive torque is detected and by allowing operation only in the direction opposite to that in which the excessive load was detected; cooling capacity degradation alarm: detects and displays cooling capacity drop due to cooling fin clogging caused by dust and cooling fan airflow reduction; igbt life expectancy forecasting: estimates the power cycle life expectancy of the main circuit s igbt semiconductor device temperature due to frequent acceleration and deceleration stoppages, and displays the estimate before the design life is reached; protection: it must have all standard protections like stall protection, instantaneous power failure, single phasing, over voltage, under voltage, over current, inverter overload, thermal overload etc; display console: it must have alpha numeric display console for programming of drive, fault display and operating condition; dynamic qr code: it must have dynamic qr code for trouble shooting; tuning facility: it must have auto tuning facility. this must enable perfect matching of motor coupled to load with regards to optimum acceleration time, deceleration time, speed regulation etc; drive programming software: suitable drive programming software along with necessary connecting cable and adapter for connection with laptop and drive should be provided to get online with the offered drive (laptop not in scope); automatic voltage regulation: it must have automatic voltage regulation function to maintain high starting torque even at reduced voltage; regenerative option: it must be capable of regenerative operation; communication protocol: modbus (rtu/serial) or ethernet (tcp/ip); make of drives: fuji- electric/yasakawa/schneider/abb only; suitable dynamic breaking resistance unit of 60% wattage rating of drive, however the value of resistance is to be decided by manufacturer as per their technical manual for crane-ho
Tender For supply of mt spares e e - set of engine gasket t3c b 928 81 70 , switch swf 201 576 , magnetic switch 19024320 , hose , cable craft 183-v-tt-50-2700 , wiperrubber blade
Tender For bid to ras bid to ras supply of main gear wheel part no vpw - 55 . , chain wheel gear pinion assembly complete part no vpw-35 . , resistance bank part no. vicpm-5 . , dc motor, part no vpw-1 . , needle roller bearing size, part no. vpw-39 . , driving chain 33 links part no vpw- 43 sl . , battery cable connector part no 0302400 , key switch part no. 0116400 , contactor assembly24 volts part no. 0425400 , fixed contact part no 0142500 , moving contact part no. 0142400 , master cylinder part no 1106700 , master cylinder service kit part no. z028700 , rear axle brake lever pin part no 11ra-19 , axle rear brake lever part no 11ra-18 . , brake shoe part no 11 ra 2by5 . , rotary switch part no. vicpd 60 . , horn 24 volts part no. 302701 . , rear axle unit part no- 11ra-1 , brake unit part no-11 ra- 2 , key switch part no. vicpa-23 . , reverse and forward switch part no. vicpa-24 , fuse link 500 amps part no. k512612 , fuse link 275 amps part no. k 512609 , carbon brush part no. 0170700 , carbon brush part no 170900 , micro switch part no. 0128400 , brake back assembly, part no. lh4024902 , brake back plate assembly part no rh 4024901 ) /bid number: gem/2026/b/7239454 * /dated: 16-02-2026 & & / bid document1 / 31