Latest wire gauge repair Tenders | Government wire gauge repair Tenders

CTN :45475071

15 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For purchase of non-consumables for ece department - purchase, dual output regulated dc variable power supply input voltage: 230v/50 hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., function generator frequency range: 0.1 hz to 5 mhz. display: 4 to 6 digit led display. output waveforms: sine, triangle, square, pulse, ramp. amplitude: 0 20 vpp. rise time: 100 ns. distortion: 1% within specified frequency range. power supply: 230 v ac 10%, 50 60 hz. output amplifier protection: short-circuit and 15 v overload protection. dc offset: 0 to 10 v adjustable. attenuation: 0 to 60 db., dso (digital storage oscilloscope) bandwidth: 50 100 mhz. sampling rate: 1 gs/s. channels: 2 (minimum). power supply: 100 240 v ac, 50 60 hz. automatic measurements: vpp, vavg, vrms, frequency, period, vmax, vmin, rise time, fall time, +width, width, +duty, duty, etc. horizontal scale: 5 ns/div 50 s/div or equivalent. vertical resolution: 8 bits (2 channelssimultaneously). vertical sensitivity: 1 mv/div 10 v/div (at input). waveform math: +, , , , invert, fft, etc. waveform storage: 16 waveforms or equivalent. communication interface: usb host and usb interface. display: 7-inch color display or equivalent. input impedance: 1 m 2% || 20 pf. accessories: 2 passive probes (1x/10x)., digital ic trainer kit with breadboard +5 v dc, 1 a regulated power supply. 12 v dc / 15 v dc, 200 ma regulated power supply. solderless breadboard with minimum 840 tie points,power distribution buses. zif (zero insertion force) ic sockets to accommodate 8 or 16 pin ics. logic input and output leds for output monitoring. 16 buffered led outputs. 16 debounced switch inputs. variable clock generator: 0.5 hz to 50 hz. single pulse output: 100 ms (buffered, positive and negative outputs). one seven-segment display with 4 bcd inputs. built-in logic switches. manual clock: debounced push-button (one pulse per press)., lvdt trainer kit ac mains power supply: 230 v 10%, 50 hz. fixed regulated dc power supply: +5 v, 12 v / 500 ma. transducer: lvdt. lvdt displacement: 20 mm (40 mm total). displacement scale: linear 20 mm. displacement display: red color 3 digit led display. excitation frequency: 4 khz. excitation voltage: ac variable excitation voltage up to 5 v., strain guage trainer kit ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual.

CTN :45465678

19 Jun, 2026 NA

Kanchipuram - Tamil Nadu

Tender For supply, installation and testing of electronic equipments - supply -ece lab equipments, single output regulated dcvariable power supply- input voltage: 230v / 50hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., dual output regulated dc variable power supply- input voltage: 230v/50 hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., function generator - frequency range: 0.1 hz to 5 mhz. display: 4 to 6 digit led display. output waveforms: sine, triangle, square, pulse, ramp. amplitude: 0 20 vpp. rise time: 100 ns. distortion: 1% within specified frequency range. power supply: 230 v ac 10%, 50 60 hz. output amplifier protection: short-circuit and 15 v, digital ic trainer kit with breadboard - +5 v dc, 1 a regulated power supply. 12 v dc / 15 v dc, 200 ma regulated power supply. solderless breadboard with minimum 840 tie- points,power distribution buses. zif (zero insertion force) ic sockets to accommodate 8 or 16 pin ics. logic input and output leds for output monitoring. 16 buffered led outputs. 16 debounced switch inputs. variable clock generator: 0.5 hz to 50 hz. single pulse output: 100 ms (buffered, positive and negative outputs). one seven-segment display with 4 bcd inputs. built-in logic switches. manual clock: debounced push-button (one pulseper press)., dc voltmeter(digital) - dc digital voltmeter - 3 digit led/lcd display, measurement range: 0 20 v dc,accuracy: class 0.5( 0.5 % full-scale), dc ammeter - dc ammeter digital - 3 digit led/lcd display, measurement range: 0 5 a dc,accuracy: class 0.5 ( 0.5 % full-scale), lvdttrainer kit - ac mains power supply: 230 v 10%, 50 hz. fixed regulated dc power supply: +5 v, 12 v / 500 ma. transducer: lvdt. lvdt displacement: 20 mm (40 mm total). displacement scale: linear 20 mm. displacement display: red color 3 digit led display. excitation frequency: 4 khz. excitation voltage: ac variable excitation voltage up to 5 v., strain gauge trainer kit - ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. instrumentation amplifiers with 3 digit display for strain / output voltage. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual., ask modulation and demodulation kit - message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. supply voltage (board): +12 v, +5 v dc. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., fpga trainer kit - must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb- uart bridge, usb cable. user manual., measurement scale: a vertical steel meter scale, usually with (1mm) graduations, for precise deflection measurement., accessories: includes a set of slotted weights (e.g., (6times 50g) or similar sets) for incremental loading.

Central Government/Public Sector

CTN :45361594

19 Jun, 2026 NA

Bangalore - Karnataka

Tender For tender for supply of digital force gauge - digital force gauge 0 1000n batch 1 , digital force gauge 0 1000n batch 2 , digital force gauge 0 1000n batch 3 , digital force gauge 0 1000n batch 4 , digital force gauge 0 1000n batch 5 , digital force gauge 0 1000n batch 6 , digital force gauge 0 500n batch 1 , digital force gauge 0 500n batch 2 , digital force gauge 0 500n batch 3 , digital force gauge 0 500n batch 4

CTN :45343668

11 Jun, 2026 NA

Madurai - Tamil Nadu

Tender For purchase of equipments for materials testing lab for civil department - spring testing machineload & displacement sensing load cell capacity: 0 10 kn accuracy: 1% fs (better if 0.5%fs) displacement sensor lvdt / digital encoder accuracy: 0.5 mmmachine design frame: rigid steel frame with crosshead movement type: mechanical screw with hand wheel (simple & robust) or electromechanical actuator (for smoother, controlled motion) crosshead travel: ~150 200 mm safety guards: transparent shields around moving partsfixtures & accessoriesspring testing compression plates (ground & parallel) tension hooks / eyelets for extension springs set of spacers / adapters for small springs tensile testing standard tensile grips wedge or screw type calibration certificate for load cell standards complianceensure compliance with basic material test standards such as: astm e4 / iso 7500-1 calibration of force measurement astm e8 / iso 6892 tensile performance & accuracy load accuracy: 1% fs displacement accuracy: 0.5% repeatability: 0.5%, rockwell cum brinell hardness testing machine min initial test force :10kgf, total test force range : 60kgf,100kgf,150 kgf, max. height of specimen :215 mmmin distance from indenter center tomachine wall :132 mm accessories : steel ballpreferred indentor 1/16" preferred steel ball: 1/16"and with all standard accessories to run the machine, direct shear machinestandard compliance:the equipment shall confirm to bureau of indian standards is 2720 (part 13) and equivalent astm international astm d3080.technical specifications:shear box size: 60 mm 60 mm 25 mm specimen size (complete with grid plates, porous stones, and specimen cutter).normal load capacity:minimum 5 kn with loading yoke and calibrated loading hanger set.shear load capacity:minimum 2.5 kn or 5 kn with calibrated proving ring (with calibration certificate).rate of strain (shear displacement):variable speed drive with controlled displacement ranging from 0.01 mm/min to 1.25 mm/min (motorised model preferred for uniform rate control).displacement measurement:horizontal displacement dial gauge: 0.01 mm least countvertical displacement dial gauge: 0.002 mm or 0.01 mm least countloading frame:rigid, heavy-duty loading frame with corrosion-resistant finish.drive system:motorised with single phase 220 230 v, 50 hz power supply.accessories (to be supplied complete):shear box assembly, proving ring with calibration chart, two dial gaugesloading weights and hanger, porous stones (2 nos.), specimen cutter, tool kit, flow table test apparatusdimensions and specifications as per is 9103, table top made from flat metal plate, minimm thickness 1.5 mm. table top size: 700 mm 700 mm, with flatness tolerance of 1.5 mm. table top marked with: scribed cross at centre, lines parallel to table edges and central circle of 200 mm diameter underside of table top reinforced to prevent distortion. total mass of table top: 16 1 kg. table top, base frame front and upper stops provided as per is 9103. lower front edge fitted with two rigid stops to transfer load directly to base frame. base frame designed to transfer impact load directly to supporting surface, minimizing bounce. stop watch digital - 2 nos scale 1 mtr 2 nos mounting wooden platform 300 mm height amc for 3 years inclusive.

CTN :45311622

09 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For supply of lab equipments - beesley s balance count : manual , overall dimension of unit : length x depth x height, 535mm x 140mm x 230mm 21 x 5.5 x 9 , net weight of the unit : 6.2 kg (13.6 lb), gsm cutter cutter type: circular, hand-operated cutting area: 100 cm ; blade : circular hardened stainless steel blade , water bath capacity : 400 ml x 12 pots; maximum temperature : ambient to 90 c; accuracy : 1 c; capacity (in liters) of main both : 25 liters (approx.); pot size : inner dia. : 79 2 mm; length : 122 mm; temperature controller : digital, pt 100 sensor ( 0.1 c accuracy); heater capacity : 3000 watts; bath size : 675 x 235 x 160 mm; power supply : single phase 220vac @ 50hz; consumption : 3050 watts; s ize(wdh) : 1100 x 350 x 250 mm; weight : 25 kg , crock meter rubbing finger shape: cylindrical; diameter: 10 0.1mm; diameter: 10 0.1mm; force: 9 0.2 n; stroke length: 100-110 mm; direction: straight line , back and front , hygrometer measurement range: 20- 80 %rh; accuracy : 2% rh; temperature measurement range: 20 - 30 c; sensor type: capacitive humidity sensor; response time 30 seconds, twist tester gauge length : 2 to 20 inch (5 to 50 cm); counting system : direct result; in-built calculations; readout in dot-matrix display; control system : microcomputer based pre-selectable / pre-programmable solid-state circuitry control user-friendly menus with membrane keypad assembly; programmable parameters : measurement unit, sample length & type, twist direction and speed index, etc.; elongation setting range : - 10 to + 100 mm; tensioning range : 1 to 90 grams (by calibrated augment weights); power supply : single phase 220vac @ 50hz; consumption : 100 watts; applicable standard(s) : astm d1422 / d1423 and is 832; physical dimensions : size (wdh) : 1000 300 200 mm; weight : 12 kg; swift/wheel circumference : 1.5 yards or 1 , yarn appearance board winder tapered board : 01 no. parallel board : 01 no; main unit : 01 no. bobbins holder stand : 01 no., crimp tester measuring length : 60 cm; tension weight : 35g; net weight of the unit: 5 kg., thickness gauge measuring range : 0.010 to 10.00 mm measuring accuracy : 0.01 mm (or) 10 microns readability : 0.01 mm; diameter of anvil : top : 75 0.2 mm physical dimensions : size (wdh) : 150 110 160 mm; weight : 4 kg (accessories included) , wrap reel meter number of leas made at a time : 10 spread of each lea : 20mm 5 counter (three digits) : digital pre-set counter with sensor operating speed : 100 5 rpm motor : 1/8 hp 230v geared motor

Central Government And Public Sector

CTN :44687431

25 May, 2026 NA

Raebareli - Uttar Pradesh

Tender For bid to ras corrigendum : tender for supply of calibration of aviation standard tools and equipments : : - battery charger alpha c20/25 , battery charger alpha c20/25 , battery discharger bc 5000 , battery discharger bc 5000 , multimeter fluke 179 , torque wrench 5-35 nm , dc power supply l-3230 , ramp tester ifr-6000 , torque screw driver a402 (0.5- 2.5 nm) , carbon monooxide meter s/n- 211222325 , combination set , combination set 0-360 degree , compass landing (sirs/189/188) , d t i digital gauge 0-10 mm , d t i gauge 0-10 mm , depth gauge 0-150 mm , digital multimeter metravi 19 , digital protactor 0-90 degree , feeler gauge , feeler gauge 0.03-1 mm , force gauge 0-200 lbf , force gauge digital , hi voltage cable tester , hole gauge , micrometer digital 0-25 mm , micrometer external 0-150 mm , micrometer inside 0-1mm , micrometer inside 0-25 mm , pressure gauge 200 psi , pressure gauge , pressure gauge , pressure gauge 0-1000 psi , pressure gauge 0-150 psi , pressure gauge 0-150 psi , pressure gauge 0-250 psi , pressure gauge 0-500 psi , pressure gauge 0-6000 psi , pressure gauge 0-6000 psi , pressure gaugte 0 - 1000 psi- n2 kit , spirit level ts/94/2 (300 mm) , spring balance 0-50 kg , stop watch analog , straight edge , surface plate 18 inchx18 inch , telescopic gauge 12 to 54 mm , torqe screw driver 2-8 nm , torqe screw driver new capri , torque wrench , torque wrench , torque wrench 20-100 lb-ft , torque wrench 2-14 nm , torque wrench 5.6 23.7 nm , torque wrench 5-35 nm , torque wrench 5-35 nm , type pressure gauge digitel 150 psi , tyre pressure gauge 0-12 kg , tyre pressure gauge 0-200psi , pressure gauge 0-250 psi , pressure gauge 17.5 kg (spark plug tester) , volt meter , digital thermohygrometer , digital weighing balance , digital thermohygrometer , air compressor capacity 50 liter , air compressor capacity 50 liter , air compressor capacity 30 liter , air compressor capacity 30 liter , lifting beam (engine sling) , mobile crane with 10 mm wire rope , chain pully with mono rail , chain pully with mono rail , chain pully with mono rail , chain sling 4 leg 8 mm link dia , mobile crane with 12 mm link chain

Central Government/Public Sector

CTN :44675127

11 Apr, 2026 NA

Sonitpur - Assam

Tender For corrigendum : supply of digital force gauge

CTN :44455226

06 Apr, 2026 NA

Thiruvananthapuram - Kerala

Tender For corrigendum : supply of timer , tem controller , oven , decompression tool , gauge , data logger , thermometer , protractor , probe , hot bonder , thermo couple , controller , tds meter , weighing balance , machine , megger , digital force gauge , infrared thermometer , lcr meter , force gauge , lux meter , micrometer , trammel bar , feeler gauge , ground fault tester , inspection machine , residual field indicator , gauss meter , intensity meterdyeglo , uve lux meter , uv light meter , visible light meter , aerocheck , tam panel psm5 , hoffmanntam panel , surface plate cast iron , protractor mount , fuel quantity test adaptor kit , dmc tool kit , elt tester , reflectometer , mx6 hybrid multi gas detector , ulb tester , analyser , tester , lrra tester , altimeter , clampmeter , air data test set , milli ohm meter , calibrator , sound level meter , vacuum gauge , static charge meter , surface resistivity meter , portable eddy current machine , hydraulic tank , gauge assy push pull , exting fire test , dynamometer , fire extinguisher system , ext fire test , calibration standard , reference standard , calibration block , safety lock actuator cargo , device check vapor seal , test set engine bleed , cart pressure , ground test motor , tensio meter , our side micrometer , bevel protector , dynamometer safety , tons gauge , dial depth gauge , dial test indicator , mechanical force gauge , hygrometer

Central Government/Public Sector

CTN :44448162

06 Apr, 2026 NA

Srinagar - Jammu And Kashmir

Tender For corrigendum : supply of 12 mm thick polycarbonate sheets for 6cm dst shear box , 12 mm thick polycarbonate sheets for 10.17 cm dst shear box , 5 mm thick polycarbonate sheets for normal load box of 6 cm dst shear box , 5 mm thick polycarbonate sheets for normal load box of 10.17 cm dst shear box , 18 mm thick polycarbonate sheets for the outer frame of 6 cm dst shear box , 18 mm thick polycarbonate sheets for the outer frame of 10.17 cm dst shear box , hp 500 digital push-pull force gauge , miran lvdt linear displacement sensor, measuring range 50-250 mm , l16-r linear actuator , microcontroller arduino uno r3 original , 2 in 1 humidifier cum dehumidifier with temperature display , torque screwdriver set , laser level , spirit level , plastic cum paper shredder , generasis-m3 m4 m5,button head internal hex cap bolt screw assortment kit , smart wifi temperature humidity monitor,temperature hygrometer sensor , cement solvent adhesive , fabrication charges for dst box and assembly

Wire Gauge Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government And Public Sector

Central Government/Public Sector

Central Government/Public Sector