Latest wooden bed Tenders | Government wooden bed Tenders

Central Government/Public Sector

CTN :45713835

18 Jul, 2026 30.00 Lacs

Mumbai - Maharashtra

Tender For repair/replacement of external electric supply distribution network with other connected items at malad, marve and kandivali under ge (n) santacruz, mumbai - supply, install, testing & commissioning pedestal cubical type double door lt bus bar chamber box of suitable size factory made modular construction fabricated out of 3 mm thick crca sheet, angle iron, channels, epoxy powder coated to give a superior finish , outdoor type , totally enclosed dust & vermin proof with locking arrangements front & back side opening system including rain shed, busbar chamber should be suitable for accomodating all aluminium bus bar strips (50mm x 10mm x 04 nos) & gi strip for earth fixed on porcelain insulators, and one independent metering module suitable for accomodating three phase volt meters & ammeter digital type, indicator lamps, cable entry/exits cut outs at bottom part, with fixing arrangement on pcc (1:3:6) type c-2 bed block with studs, bolts, nuts & washers, danger notice board with scull suitable for 415 volts or required size to be fixed on pannel including dismantling of old bus bar panel all as specified and directed by engr-in charge.notes:-(a) aluminium bus bar duly covered with colour coded shrinkable sleeves of required size for phases and neutral - 01 set(b) mccb 4 pole , ics=100%icu- 25 ka, 415 volts, 100 amps , with thermal adjustable and fixed magnetic setting with extended terminals -02 nos.(c) digital multifunction meter of size 96x96 mm to measure current, voltage, frequency and power factor with built in selector switch and programable ct of appropriate ratio.-01 no make- imp/automatic electrical(ae)/ l&t / havells/ meco(d) panel indicating lamp neon/led type (red ,yellow & blue) with lamp holders - 03 nos(e) panel instrumental wiring with frls suitable size but not less than 2.5 sqmm copper wire single core - 01 job(f) necessary sizes of lugs for fixing of cables in bus bar deemded to be included rate quoted by the contractor.make of mccb & mcb: larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 400 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:- larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 160 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 16 ka 100 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 250 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb all as specified and directed by engr-in-charge make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supplying, laying,connecting, testing & commissioning lt ug pvc insulated, heavy duty, 1100 v grade electric cable with aluminium conductor of size 16 sqmm x 4 core, laid in trenches or passing through pipe or fixed to wall, making all connections with and including provision of necessary glands, lugs, bushing etc as required including taking down old unserviceable cable complete all as specified and as directed by engineer-in-charge of following sizes:-note : earthwork excavation, dwc

State Government

CTN :45741975

10 Jul, 2026 NA

Jammu - Jammu And Kashmir

Tender For supply of single / double wooden bed with/without storage (v2) (q2) , sofa set or couch (handicraft) (v2) (q3)

State Government

CTN :45714601

07 Jul, 2026 NA

Srinagar - Jammu And Kashmir

Tender For supply of single / double wooden bed with/without storage (v2) (q2) , sofa (v3) (q2) , modular table / meeting table / centre table (v2) (q2) , steel almirah / cabinets (v4) (q2)

CTN :45583729

04 Jul, 2026 NA

Meerut - Uttar Pradesh

Tender For corrigendum : supply of single / double wooden bed with/without storage (v2) (q2) , sofa (v3) (q2) , wooden shelf / case / rack / credenza / modular storage (v2) (q2) , table (handicraft) (v2) (q3) , chair or bench or stool (handicraft) (v2) (q3)

CTN :45718452

10 Jul, 2026 NA

Leh - Jammu And Kashmir

Tender For supply of steel almirah / cabinets (v4) (q2) , single / double wooden bed with/without storage (v2) (q2) , chair for general purpose (q2) , metal beds (v3) (q2) , modular table / meeting table / centre table (v2) (q2) , sofa (v3) (q2)

CTN :45582546

03 Jul, 2026 NA

Silvassa - Gujarat

Tender For corrigendum : supply of single / double wooden bed with/without storage (v2) (q2) , chair for general purpose (q2) , modular table / meeting table / centre table (v2) (q2) , wooden almirah / wardrobe (v2) (q2)

State Government

CTN :45623005

02 Jul, 2026 NA

Jammu - Jammu And Kashmir

Tender For corrigendum : supply of wooden podium,modular table / meeting table / centre table (v2),modular table / meeting table / centre table (v2),modular table / meeting table / centre table (v2),chair for general purpose,chair for general purpose,sofa (v3),single / double wooden bed with/without storage (v2),steel almirah / cabinets (v4),waiting area / airport terminal / public place / reception area chair or seat (v2),modular table / meeting table / centre table (v2)

Central Government/Public Sector

CTN :45319237

01 Jul, 2026 NA

Shajapur - Madhya Pradesh

Tender For corrigendum : supply of godrej interio modular table with particle board table top and wooden or engineer wood understructure , godrej interio 1 seater sofa with leatherite cover , godrej interio modular table with particle center table , godrej interio queen size wooden bed with headboard only , godrej interio two layers foam mattress size 1981 mm x 1524 mm , godrej interio na bed side table , godrej interio revolving chair with center tilt mechanism , godrej interio 5 seater sofa with leather fabric cover godrej interio 3 1 1

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

CTN :45691072

09 Jul, 2026 NA

Bilaspur - Chhattisgarh

Tender For e – tender for the purchase of medical equipment and furniture for statecancer institute, koni, cims bilaspur (c.g.), government of chhattisgarh(2nd call) - secretariat /executive office , table-rectangular, , executive, , &revolving chair with high back, , executive &revolving chair with high back-ergonomic chair, executive office table with side, , storage-rectangle/l shape, , executive &mesh-revolving chair with arms & mid back, , revolving chair, , special sofa 3, , seater- tubular steel, , rectangular-modular centre table with glass top, computer table with printer/copier/fax combination desk, , wall mounted & over head chamber type wooden wardrobe, registration desk(01 no) & window display cum counter rack- customized with all locking system- customized, round wastepaper basket, made of steel, , white board(pt notes), , notice board, , whatnot/corner shelf, , clock, 12" diameter. round surface, , composite office desk, pvc wall decor, , ot table (hydraulic) side end control, , medicine trolley with 4 drawer, airway crash cart -abs, , cardiac table, , writing board, , monitor trolley, , stretcher trolley, cylinder trolley, , multipurpose trolley for luggage etc., , trolley platform, , stand saline cum irrigator, adjustable, , two foot step, revolving stool, , dressing drum (03 sizes) kit, , kidney tray s.s (03 sizes) kit, , catheter tray s.s. (02 sizes) kit, , shoe rack-l size, , medical/ infectious waste bin kit w/lid, sterilizer/autoclave( horizontal) with accessories, , sterilizer/autoclave (vertical) with accessories, , kick bucket, board room table-u shape/modular conference table, , digital clock/led kiosks, , token display, , attendant stool, , bed side table with one box and one drawer(clinical cabinet), trolley mayo's, , vinyl fooring/epox floor & ot wall paneling

Wooden Bed Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

State Government

State Government

State Government

Central Government/Public Sector