Feeder Tenders

State Government

CTN :43117029

17 Dec, 2025 NA

Delhi - Delhi

Tender For sic of submersible pump set and all allied e/m equipment for rebored tube well near h.no.-116c shahpur jat in greater kailash constituency ac-50. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 10 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point:200 lpm on 90 mtr. head. having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved make, supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted.a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no.b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 noc) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no.e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable bankingg) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos. complete wiring & installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated & pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs.make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., s/o nut & bolts of 1/2 dia of different size i.e. 1.5 dia& 2.5 long full threaded., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 8-10 inch diameter made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2 dia. with locking arrangement by nuts & bolt., earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

State Government

CTN :43122895

20 Dec, 2025 3.59 Lacs

Kheda - Gujarat

Tender For urgent supply of plummer blocks for belt feeder installed at chpm-8 wtps

corporations/Associations/Others

CTN :43118299

30 Dec, 2025 81.50 Lacs

Deesa - Gujarat

Tender For bi-annual rate contract for erection of 66 kv tr bay/feeder bay, breaker replacement, mesh type earthing and bus strengthening work at various sub-stations under deesa division of palanpur circle approved under r&m 24-25 and 25-26

corporations/Associations/Others

CTN :43103502

22 Dec, 2025 NA

Salem - Tamil Nadu

Tender For mtps-1 - mill plant -unit ii – attending the break down / preventive maintenance works such as overhauling of gravimetric feeders, mechanical face seal assembly, renewal of vertical shaft thrust bearing, worm shaft thrust and radial bearing, airport ring assembly, scraper assemblies replacement, rectification & refixing of feeder belt/ feeder pulleys bearings replacement of half coupling and its pins / under bowl cleaning, rectification & refixing of knife edge gate valve assembly, decouple the flexible coupling & assembling and coal chock releasing in mill / feeder, etc. for a period of 365 days from the date of commencement of work.

corporations/Associations/Others

CTN :43112945

23 Dec, 2025 NA

Salem - Tamil Nadu

Tender For name of the work: mtps –i - mill plant - unit i to unit iv – cold vulcanizing of 1200 mm width feeder belts

corporations/Associations/Others

CTN :43113001

23 Dec, 2025 NA

Salem - Tamil Nadu

Tender For : mtps-1 - mill plant -unit iii – attending the break down / preventive maintenance works such as overhauling of gravimetric feeders, mechanical face seal assembly, renewal of vertical shaft thrust bearing, worm shaft thrust and radial bearing, airport ring assembly, scraper assemblies replacement, rectification & refixing of feeder belt/ feeder pulleys bearings replacement of half coupling and its pins / under bowl cleaning, rectification & refixing of knife edge gate valve assembly, decouple the flexible coupling & assembling and coal chock releasing in mill / feeder, etc. for a period of 365 days from the date of commencement of work.

Central Government/Public Sector

CTN :43126179

20 Dec, 2025 NA

Varanasi - Uttar Pradesh

Tender For fully machining of feeder front liner(hy-504.14)as per drg.36515600108/01 scrap wt 4.18 kg per no.

Central Government/Public Sector

CTN :42952778

15 Dec, 2025 NA

Barh - Bihar

Tender For corrigendum : supply of m4851000033_ blt cnv edls, 1219mm, 1028-st1-mills_ feeder belt for milling system

Central Government/Public Sector

CTN :43128407

31 Dec, 2025 NA

Chandipur - Odisha

Tender For repair replacement of lt cables network, lt breakers and panels feeder pillars, earthing and allied works at itr tech area, lc area, site a, site b and site c at itr chandipur

Central Government/Public Sector

CTN :43124135

23 Dec, 2025 NA

Dhanbad - Jharkhand

Tender For repairing and changing of damage discharge bunker horizontal gurder angle base plate of atlas copco feeder breaker at bnr siding rocp/sj.

By Cities

By States

By Agencies

By Ownerships

By Sectors