Measurement System Tenders

Central Government And Public Sector

CTN :45487108

08 Jul, 2026 NA

Raipur - Chhattisgarh

Tender For supply of wheel wise load measurement system in electronic in motion weigh bridge (eimwb) as per clause no. 2.1.12 of rdso specification no. wd-29-misc-19(rev.1). ]

CTN :45332868

19 Jun, 2026 NA

Sonitpur - Assam

Tender For corrigendum : supply of small store shelter sys room conduit pipe 15 mm dia , pvc round oblique square block , fire extinguisher of one kilogram capacity comma dry power type along with its accessories , earthing plate 600 x 600 x 6 mm galvanised steel suitable for gi strip fittings , ci earth pit cover of size 300 x 300 x 6 mm with angle iron of size 20x20mm comma 3 mm thick with ms frame , funnel fitted with 20 mm diameter gi pipe 1 point 5 m long pipe , gi wire 4 mm diameter for earthing , charcoal , salt normal , air termination single pointed aluminium rod 12 mm dia and 300 mm long , testing point terminal block make of gun metal and phosphorus bronze size 75 x 75 x 25 mm drilled and screwed , aluminium strips 25 x 3 point 00 mm , galvanised iron strip 32 x 6 mm , ci earth pit cover of size 300 x 300 x 6 mm with angle iron of size 20x20mm coma 3 mm thick with ms frame , insulating pvc block 75x75x30 mm with insulating clamp nut and bolt , study chair of size length 56 cm comma height 82 cm and width 56 cm , study table of size 4 feet x 2 feet comma wooden top on round tube structure with three drawers on one side , steel almirah of size 1855mm with 4 shelves ms sheet doors and and locker 1 point 00mm thick , mild steel rack adjustable comma sheet 1 point 00mm thick comma nuts and bolts are in hexagon blck steel , hand held trolley of size 1200 x 900 x 1200 mm of 2 mm thick ms platform , kassi with handle , black steel sr shovel spade belcha , plaster trowel with wooden handle , showel square nose 14 gauge blade size 310 x 245 mm , plumb bob iron , crow bar 1 point 5 inch dia 4 feet long , hammer 1 kg with wooden handle durmut , hammer 0 point 5 kg with wooden handle durmut , brick line 30 mtr nylon dhaga , traveler brick mason 4 inch 305mm , sprit level , measuring tape 30 mtr steel , water bucket steel 13 inch dia , picks axes with chisel and point ends kudali 14 cp nominal weight 3 point 0 kg , lime brush best quality , painting brush 100mm , hacksaw frame large with blade 05 nos , galvanised iron pan mortar tasla comma 18 gauge 20 inch dia , wooden waterproof plywood thickness 12mm , nails various sizes , rammer earth with handle minimum weight 5 kg without handle , tester for electrician with plastic handle 150mm , electric drill machine heavy duty 500 watt electrical backup with battery and charger , drill bits hss 5mm comma 8mm and 10mm dia for electric drill machine , electric tile cutting machine with interchangable blades 05 nos , electrical sheet cutter machine with blade , puf rivet machine , centre punch 8mm dia best quality , plumbing tool kit , water level pipe 30 mtr long

CTN :45404122

19 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using

CTN :45475064

15 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For purchase of non-consumables for mechanical department - purchase, open cup apparatus standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valve body: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation, closed cup apparatus standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety: over-temperature cut-off flame safety control

State Government

CTN :45244313

19 Jun, 2026 1.66 Crore

Gandhinagar - Gujarat

Tender For corrigendum : supply of smart energy meters with head end system services in gift city - 1200009630: 1p2w 240v 10-60a cl-1.0 smart meterdesign, engineering, manufacturing, inspection & testing at manufacturers works before dispatch, supply and delivery at destination (at gift store) of ac whole current 1 phase 2 wire, isi marked, 1.0 class accuracy, 10-60 a smart energy meter with dlms protocol & bidirectional communication facility & remote connect/disconnect switch. the meter shall communicate with head end system (hes) on any one of the communication technologies mentioned in is:16444 part 1 compliant with nbiot communication module fall back to 2g, as per the requirement of the utility for measurement of import and export active energy (kwh) with initial and sustained accuracy of class 1.0 for solidly earthed system with balanced and unbalanced loads having power factor in the range of zero to unity (lagging/leading). the meter shall be compatible to common meter reading instruments and other associated instruments & software for remote reading as per requirements given in this specification, 1200009631: 3p4w 240v 10-100a cl1.0 wc smart meterdesign, engineering, manufacturing, inspection & testing at manufacturers works before dispatch, supply and delivery at destination (at gift store) of ac whole current 3 phase 4 wire, isi marked, 1.0 class accuracy, 10-100 a smart energy meter with dlms protocol & bidirectional communication facility & remote connect/disconnect switch. the meter shall communicate with head end system (hes) on any one of the communication technologies mentioned in is:16444 part 1 compliant with nbiot communication module fall back to 2g, as per the requirement of the utility for measurement of import and export active energy (kwh) with initial and sustained accuracy of class 1.0 for solidly earthed system with balanced and unbalanced loads having power factor in the range of zero to unity (lagging/leading). the meter shall be compatible to common meter reading instruments and other associated instruments & software for remote reading as per requirements given in this specification, 1200009632: 3p4w 240v -/5a cl0.5s ct smart meterdesign, engineering, manufacturing, inspection & testing at manufacturers works before dispatch, supply and delivery at destination (at gift store) of 3 phase 4 wire, isi marked, 0.5s class accuracy, fully static lt current transformer (ct) operated smart energy meter with dlms protocol & bidirectional communication facility. the meter shall communicate with head end system (hes) on any one of the communication technologies mentioned in is:16444 part 2 compliant with nbiot communication module fall back to 2g, as per the requirement of the utility for measurement of import and export active energy (kwh) with initial and sustained accuracy of class 0.5s for solidly earthed system with balanced and unbalanced loads having power factor in the range of zero to unity (lagging/leading). the meter shall be compatible to common meter reading instruments and other associated instruments & software for remote reading as per requirements given in this specification, 1200009630: 1p2w 240v 10-60a cl-1.0 smart meterdesign, engineering, manufacturing, inspection & testing at manufacturers works before dispatch, supply and delivery at destination (at gift store) of ac whole current 1 phase 2 wire, isi marked, 1.0 class accuracy, 10-60 a smart energy meter with dlms protocol & bidirectional communication facility & remote connect/disconnect switch. the meter shall communicate with head end system (hes) on any one of the communication technologies mentioned in is:16444 part 1 compliant with nbiot communication module fall back to 2g, as per the requirement of the utility for measurement of import and export active energy (kwh) with initial and sustained accuracy of class 1.0 for solidly earthed system with balanced and unbalanced loads havin

Central Government/Public Sector

CTN :45465699

23 Jun, 2026 7.00 Lacs

Dinajpur - West Bengal

Tender For supply of laboratory consumables under ntep for the office of the chief medical officer of health and the secretary dh and fws of uttar dinajpur district - laying and jointing pvc pipe. heading, plastic disposable sputum containers- wide mouth(plastic disposable sputum containers (60ml capacity) (water tight, screw-top, translucent opalescent, polyethylene of thin plastic) (burning easily and appropriate size (at least 4 cm diameter)), diamond marker pencil (6 (15.24 cm.) holder with artificial diamond (hard stone) embedded at one end with screw cap, to mark on microscope glass slides), water bucket (plastic) (water bucket (plastic) with tap 40 ltr capacity of good quality), slide holding forceps (stainless steel) (slide holding forceps (stainless steel) 15 cm), plane tissue paper rolls (plane tissue paper rolls (size+ length 21 mtr x breadth 10cm (non doted) (two ply) ), foot operated paddle bucket plastic with cover (foot operated paddle bucket plastic with cover (12 ltrs capacity)), measuring cylinder 1000 ml (measuring cylinder 1000 ml capacity (glass) round bottom), measuring cylinder 500 ml (measuring cylinder 500 ml capacity (glass) round bottom), measuring cylinder 100 ml (measuring cylinder 100 ml capacity (glass) round bottom), filter paper type-1 (filter paper whatman no1.11 cm diameter containing 100 leaves per box), filter paper type-2 (filter paper whatman no1.15 cm diameter containing 100 leaves per box), stickers adhesive labels (stickers adhesive labels (small size) for sputum containers), water bath with thermometer with digital temp. meter (water bath with thermometer with digital temp. meter 5 liter for the preparation of carbolfuchsin), lens clean tissue paper(lens clean tissue paper 100 pages pack), plastic tray (plastic tray 24 x12 good quality), spirit lamp aluminum (spirit lamp aluminum 50 ml), drop bottle plastic (250ml capacity built in stem all polypropylene; leak proof screw cap made of polypropylene), storage for stock bottle (plastic) (white bottle 2 ltrs capacity), binocular microscope cover (plastic good quality), balance with cover box (can measure 10mg accuracy to 200 mg digital + battery system), broom stick (8) (broom stick (8 ) bundle of 100 pcs good quality), smear preparation loop (plastic loop with inner diameter 3-4 mm for smear preparation of biological specimen), slide box-type-1 (slide box (50 capacity) plastic), slide box-type-2 (slide box (100 capacity) plastic), glass slide new glass slide (glass slide new glass slide size 76mmx26mm, thickness 1.3 mm, edges polished, sealed in a moisture absorbing dassicant pack scratch free), silica gel (big 25gm), silica gel (blue small (04gm)), absorbent cotton roll (absorbent cotton roll 300gm/450gm), para film ((2 wide) 250ft). refractive index of 1.48. it should be colourless, odorless, transparent, free from fluorescence in day light with relative density of 0.827 to 0.890, viscocity of 110 to 230m pas, specific gravity of 0.76-0.78 at 15.5 degree c), biohazerd labels (biohazerd labels 4 x 2.875 ), thin transparent plastic pkt. (thin transparent plastic pkt. (8 x 6 )), glass rod (glass rod 6-8 mm dia x 20 length), thermocol box (thermocol box 6.5 x7.5 x7.5 ), thermocol transport box (size. thickness of box 2.5cm, outer dimension: 18.5cm length x 13 cm breadth x 14cm hight (with lid), inner dimension:14.5cm length x 8cm breadthx 13 cm hight (with inner part of lid)), stop watch (digital), thin black permanent marker pen (fine tip), zip lock plastic pouch (zip lock transparent pkt. 10 x14 plastic pouch), zip lock plastic pouch (zip lock transparent pkt. 06 x06 plastic pouch), alminium vessel (5.5 ltr (3mm gauge)), pvc tape (2.5 ), rubber band ( nylon), gel pack (250gm), gel pack (500gm), falcon tube (falcon tube (sterile)material: polypropylene, capacity: 50ml,tube style: centrifuge, bottom style: conical, neck style: wide, top style: threaded, max rcf:15500xg, graduations: yes, graduations range: 5-50 ml, graduation interval: 2.5 ml, colour

Central Government/Public Sector

CTN :45475649

17 Jun, 2026 NA

Diamond Harbour - West Bengal

Tender For lab items of diamond harbour health district - laboratory materials, sputum container (good quality, 30 ml, diameter- 40 mm, water tight, leak proof, polypropylen, disposable), falcon tube (50 ml conical tube, sterile, polypropylen, centrifuge type, wide neck, good quality,leak proof cap, highly visible solvent resistant, threaded top, max. rcf - 15500 xg, graduation range from 5-50 ml, graduation interval -2.5 mm, high density polyethylene cap, cap diameter - 35.2 mm approx., no self standing, outer diameter 29.1 mm approx, length - 114.4 mm approx., disposable, no rack, able to withstand a temp. 121 degree celsius at 15 lbs per inch square for 15 minutes., phenol crystal (nice) 500 gm/bottle, 98.08% sulphuric acid, 500 ml per bottle nice, phenolic solution (40% pure, bengal chemicals) 5 litre/ jar, methylated spirit for burning 500 ml/bottle, distilled water (5 litre/ jar, good quality), whatmann no.1 filter paper (100 pcs./box), lens paper (good quality, book of 100 pages), adhesive label for sputum container (good quality) 500pcs packet, slide box for 100 slide (good quality), dropping bottle (tarson, 100 ml per bottle), spirit lamp (good quality), funnel (borosil, 10 cm diametre), funnel (borosil, 5 cm diametre), zipper pack (5"x7", good quality), zipper pack (8"x10", good quality), parafilm for falcon tube pack (good quality), wooden rack for slide keeping (good quality, size 2"x 6"), envelope for rbrc(eqa ,good quality), size 9" x4", microscope hallogen bulb, 20 watts (philips), t.t. roll / soft tissue ( safex plus, length 125 mtrs ), thermocol transport box size: thickness of box- 2.5 cm, outer dimension: length(l)- 18.5 cm, breadth(b)- 13 cm, height(h) - 12 cm(without lid), height(h)- 14 cm (with lid), inner dimension: l- 14.5 cm, b- 8 cm, h- 12 cm, (without lid), h- 13 cm, (with inner part of lid), for sputum transport (cold chain),disposable with required no. of gel pack: 2 per box, disposable., diamond marker (good quality) for slide marking, hypochlorite solution, measuring cylinder, 1000ml, weight machine, welsar company {model no. 3gb 300gm (max) 01g (min)}, measuring cylinder, 500ml, measuring cylinder, 250ml, staining rack, large size (30 slided rack), glass rod ( l-18inch w-3-4 mm), absorbent cotton -400 gm, non-absorbent cotton-400 gm, basic fuchsin powder ( for microscopy) 25gm/packet,(marck), methonal (for reagent preparation) stanbio, borosil jar 5 lt. ( round bottom high neck glass), borosil jar 2.5 lt. ( round bottom high neck glass), methylene blue, 25g, campany name :- merck, reagent stock bottle : 2ltr glass bottle (borosilicate glass), immersion oil (marck),30 ml/bottle, slides ( new glass slide ,blue star), liquid paraffin(heavy ) marck 50ml/bottle

State Government

CTN :45493017

30 Jun, 2026 NA

East Khasi Hills - Meghalaya

Tender For supply of sized ii medium sized fine tipped iii fine plain 4 each , forceps dissecting forcep adson heavy medium sized medium sized fine tipped fine tipped four each , forceps dissecting plain 12 pt 5 cm , forceps dissecting plain 18 cm , forceps dissecting toothed 12 pt 5 cm , forceps dissecting toothed 18 cm , forceps nasal dressing , forceps ovum heywood smith 25 cm , forceps sinus 18 cm , forceps sterilizer cheatle , forceps tongue , foreign body forceps hooks , gall stone holding forceps , hartman tuning fork , health aural forceps , heany hystectomy forceps 20 cms st and curved , kelly curved on flate box joint 14 cms haemostatic forceps , kidney tray ss 10 inch , kidney tray ss 8 inch , knife bard parker handle no 3 , knife bard parker handle no 4 , kochars intestinal forceps , kochar s intestinal forceps curved on flat 23 pt 8 cm , mayes curved in flat 16 pt 5 cms scissors , mayo artery forceps on pin , mayo peen curved on flat box joint 16 pt 3 cms haemostatic forceps , mcindoe scissors , metzenbaum scissors straight and curved , mosquito artery forceps curved , nasal dressing forceps , needle cutting and non cutting for suture tray , needle holder 19 cm , needle holder for suture tray , right angle mixter forceps long , right angle mixter forceps medium , right angled forceps laheys , scissor curved on flat mayo 19 cm , scissors counter 18 cm , scissors dressing straight both point blunt 12 pt 5 cm , scissors dressing straight both point sharp 12 pt 5 cm , scissors straight mayo 19 cm , speculum nasal second largest , splint knee thomas collapsible 25 inch , stand transfusion metal iv stand , steriliser electric for surg instrument 430 mm into 150 mm internal ac 230 volts 2000 watts complete , steriliser steam high pressure drum shallow for size 28 pt 5 cm into 12 cm , sterization drums , surgeon hydraulic chair , suture scissor for suture tray , suture tray , syringe enema higginson , table dressing , tilleys forceps , tissue cutting scissor , torch light , tray ss 10 inch into 8 inch with lid , tray ss kidney shaped 25 cm , tray ss shallow size 27 pt 5 cm into 22 pt 5 cm , tray ss shallow size 35 cm into 30 cm , tray with wrapper for suture tray , tuning fork , umbilical cord scissors , vaccine carrier , vascular forceps angular , vascular forceps straight , weighing machine

Central Government/Public Sector

CTN :45488083

16 Jun, 2026 NA

Multi City - Jharkhand

Tender For auction sale of others - disposal of scrap released materials such as: (1) smps ips dcdp (r), qty=02 nos. (2) smps ips smrs (r), qty=03 nos. (3) ufsbi (r), qty=10 nos. (4) data logger, qty=02 nos. (5) universal axle counter/reset box, qty=24 nos. (6) copper strip, qty=109.9 mtr. (7) ct box 20 pairs, qty=35 nos. (8) ct box 10 pairs, qty=10 nos. (9) eld, qty=03 nos. (10) track feed battery charger, qty=81 nos. (11) ct box 50 pairs, qty=01 no. (12) ips status monitoring panel, qty=03 nos. (13) ufsbi alarm panel presentive, qty=08 nos. (14) fire alarm panel, qty=05 nos. (15) lightning surge protection unit, qty=03 nos. (16) lpd spd box, qty=03 nos. (17) remote terminal unit, qty=02 nos. (18) stm cabinet, qty=04 nos. (19) autometic battery charger, qty=01 no. (20) filter unit, qty=08 nos. (21) track circuit choke type-b, qty=162 nos. (22) sm penal c double line, qty=04 nos. (23) fire extingusher, qty=04 nos. (24) vft transformer, qty=60 nos. (25) relay, qty=1337 nos. (26) ctr, qty=10 nos. (27) signal post (r), qty=35 nos. (28) location box half (r), qty=38 nos. (29) location box full (r), qty=130 nos. (30) relay rack, qty=21 nos. location:- released materials of rvnl lying near lthr station in ttipl campus(ssr), sse/sig/brwd, jharkhand.

State Government

CTN :44539441

24 Jun, 2026 NA

Ukai - Gujarat

Tender For corrigendum : providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - wt5131g work of white metal bearings clearance magnetic centre air gap measurement setting and emergency replacement lifting and shifting o h dismentalling and checking ..

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government And Public Sector

State Government

Central Government/Public Sector

Central Government/Public Sector

State Government

Central Government/Public Sector

State Government