Tender For auction sale of condemned - damaged air baloon (as its condition),condemned - waste gi scrap (as its condition),condemned - empty plastic barrel(as its condition),condemned - brake shoes with brake lining (assorted) (as its condition),condemned - atomizer (assorted)(as its condition),condemned - radial tyre, nylon tyre,condemned - 10.00 x 20 radial tyre(as its condition),cond - tyre buffing dust (available at chrompet tyre plant) (as its condition),condemned - old aluminium cut pieces (as its condition),condemned - bs iii radiator core (alu.) (as its condition),condemned - radiator inter cooler (alu) (as its condition),condemned - 12v 21p (150 amps) plastic battery (as its condition),condemned - 12v 25p (180 amps) plastic battery (as its condition),condemned - self motor (assorted)(as its condition),condemned - alternator (assorted)(as its condition),condemned - used oil in 210 lts barrel (as its condition),condemned - leyland bs iii wheel disc (as its condition),condemned - bs iii tyre lock ring(as its condition),condemned - m.s. roofing iron structure(as its condition),condemned - m.s. roofing iron structure (as its condition),condemned - auto iron (as its condition),condemned - brake drum (as its condition),condemned - broken spring leaves (as its condition),condemned - radiator with iron frame bracket (as its condition),condemned - power steering box with braket (as its condition),condemned - clutch disc with centre hub (assorted) (as its condition),condemned - door cylinder (assorted) (as its condition),condemned - hydraulic jack (assorted) (as its condition),condemned - rear engine bed, front engine bed (as its condition),condemned -radiator top tank, water pump,condemned - air compressor assly ,turbo charger etc (as its condition),condemned - gear box counter shaft without gear - etc (as its condition),condemned - fly wheel - etc (as its condition),condemned items-kre moving and brush motor gear box -etc(as its condition),condemned - open metal barrel (as its condition),condemned - bvc closed metal barrel (as its condition)
Tender For ca no.cwe bly/ge (e)/130 of 2025- 2026special repair to animal line (bldg no p-89) in brake stable of rts and depot hempur under ge east bareilly
Tender For tender for supply of oem spares for battery truck -normally open contact assembly 150amp 1 no part no je181500 , steering gear assembly part no fw43610 , carbon brush part no je070010 , axle shaft oil seal part no jm052978 , four step speed controller assembly part no je180800 , master cylinder part no jm012682 , moving contact operator part no je181509 , rear axle 19 teeth part no jm640969 , roller bearing part no 539030206 , liner leading part no jm011927 , master cylinder seal kit part no jm016637 , dc coil assembly part no je180503 , properller shaft assembly part no fw42934 , cup axle shaft bearing part no jm052800 , rear hub and drum assembly part no jm016293 , axle shaft bearing retainer part no jm802887 , outer grease retainer part no jm640885 , grease protector part no jm640888 , split pin part no g127204 , left brake assembly part no jm018409 , right brake assembly part no jm018410 , rear brake wheel cylinder assembly part no jm012626 , rear brake wheel cylinder kit part no jm012661
Tender For supply of machinery/tools for various parks at pul pehladpur ward no. 179 in central zone - brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hp max output shaft speed at cutting attachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml. weight( dry,without cutting attachment & deflector): should not be more than 7.5 kgclutch: centrifugal type, clutch shoe support base & lining metal only. multi function handle: should have acceleration ,on/off switch at right handle. brushcutter harness: should be double shoulder harness only. anti vibration system: must have 4- point aniti vibration system. vibration level in m/s2 at right handle : should not be more than 2.5 m/s2 sound pressure level db(a): should not be more than 105 db(a) drive shaft design: must have drive shaft ends square design type only. certification : must have valid en certificaton, petrol operated pole prunnerengine : single cylinder, 2 stroke, air cooled onlydisplacement: should be between 25-30 cc power output : should be minimum 1.2 hpweight (dry without cutting attachment & fuel ): should not be more than 7.5 kgfuel tank capacity (ml): should be minimum 400mlchain oil capcity (ml): must have minimum 200 ml.clutch : clutch shoe linining should be metal only.guide bar length : minimum 30cm guide bar and chain : should have same manufacture only .chain type : every drive link need groove & small oil holes for better lubrication. saw chain pitch should be 1/4" or 3/8picco only and drive link thickness must have 1.1 mm or 1,3 mm.max.output shaft speed (rpm): should be minimum 8000 rpm at chain sprocket.equipment total length with guide bar and chain ( cm ) : should be mimimum 220 cm - compressed & total length of equipment - minimum 350 cm - extended. sound pressure level (db/a): should not be more than 95 db(a)vibration measurement m/s2 at control handle - extended poistion : should not be more than 5.5 m/s2certification : must have tuv certification with test standard en iso 11680., hedge trimmerengine: 2- stroke - single cylinder air cooled.engine displacement: should be between 20-25 ccpower output: should be minimunm 1 hpfuel tank capacity: minimum 400 mlweight: should not be more than 6.0 kgclutch: clutch linning should be metal only.handle: must have rotating multi-function handleanti vibration system: must have spring loaded technology for anti vibration system design: should have double sided blade with tooth spacing minimum 35mm bar length: minimum 600 mmblade: should have chrome plated -anti corrsion. stroke rate ( l/min): minimum 3000 vibration level m/s2 at right handle: should not be more than 3.5 m/s2.sound pressure level (db..(a)): should not be more than 95certification: should have tuv with en iso 10517:2009, lopperanvil tree branch lopper lade material - high carbon steel with hard surface treatment, overall length - not less than 914 mm handle material - similar materil as per requirement, weight - 1.5 kg., cutting dia - not less than 38mm
Tender For spare parts for bd 80 veh - repair and refitment of c frame assy part no nk, repair and refitment of radiator guard a part no nk, repair & refitment of angle blade part no nk, repair & refitment of brake assy part no nk, repair & refitment of stg control valve part no nk, repair & refitment of steering clutch as part no nk, repair & refitment of main clutch assy part no nk
Tender For supply of weather strip , crank oil seal rear , rectifier plate , regulator sr 60 , cylinder head gasket , timing belt tensioner , timing belt , i c motor , water pump assy , propeller shaft uj cross , steering gear box repair kit , pully tff , door beading lh , door beading rh , speedometer head , transfer case mounting bracket , brake shoe lock , tff air pressure pipe