Fasteners Tenders

Co-operative

CTN :37518230

20 Sep, 2024 NA

Mehsana - Gujarat

Tender For quotation for 2 nd wheel,366,pbl,52k-d112m4, 1 st wheel,mtr parts,724,pbl, 2 nd pinion,337,pbl,63 k, sprct smplx,:ms,p1in,t:19,:40mm,:k12x6mm

State Government

CTN :37419981

23 Sep, 2024 1.68 Crore

Kunnamangalam - Kerala

Tender For corrigendum : supply of materials mahatma gandhi nregs - kunnamangalam block(mavoor,perumanna,peruvayal) - materials, stone aggregate(single size): 40 mm nominal size, stone aggregate(single size):20 mm nominal size, stone aggregate(single size): 10 mm nominal size, stone aggregate(single size):06 mm nominal size, bamboo 25 mm dia 2.5 meter long, portland cement, bright finished or black enameled mild steel screws 40 mm, bright finished or black enameled mild steel screws 20 mm, water thinnable cement primer for interior wall surface, having voc content less than 50 gms/litre, exterior primer, synthetic enamel paint in black or chocolate shade, plastic emulsion paint, rolling shutter made of 80x1.25 mm machine rolled laths, top cover for rolling shutters 1.25 mm thick, 27.5 cm long wire spring grade no 2 for rolling shutters, royalty for good earth, coarse sand (zone iii), fine sand (zone iv), mild steel round bar 12 mm dia and below, mild steel round bar above 12 mm dia, average rate of mild steel round bars for reinforcement, twisted steel/deformed bars, structural steel such as tees, angles, channels and r.s. joists, flats up to 10 mm in thickness, mild steel sheets for tanks, mild steel hooks, galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots, galvanised steel j or l hooks 8 mm dia, bolts and nuts up to 300 mm in length, iron pintels including weldded pin, stone for masonry work, second class kail wood in scantling, second class kail wood in planks, g.i limpet washer, bitumen washer, g.i. plain washer thick, wire nails, mild steel sheets with bolts and nuts to rest on pintels, c.i bracket for wash basin and sinks, g.i. pipes 40 mm dia, g.i pipes 50 mm dia, polyethylene water storage tank with cover and suitable locking arrangemnet, black plastic seat(solid) with lid c.p brass hinges and rubber buffers, 15 cm c.p brass tap, c.p brass waste 32 mm, vitreous china pedestal type water closet, float glass sheet of nominal thickness 4 mm (weight not less than 10kg/sqm), hollock ballies 125 mm diameter, vitreous china flat back wash basin 550x400 mm, mild steel tubes hot finished welded type, red oxide zinc chromate primer, rawl plug 50 mm (designation 10 nos), stainless steel kitchen sink - without drain board 470x420 mm bowl depth 178 mm, white vitreous china 10 lit. (full flush) capacity controlled low level flushing cistern with all fittings, epoxy paint, flushing cistern p.v.c. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe), neoprene/epdm rubber gasket, 15 mm ptmt bib cock, boulder 50 mm to 200 mm, gravel 5 mm to 10 mm, gravel 1.5 mm to 2 mm, ceramic glazed tiles ist quality minimum thickness 5 mm in all colours shades and designs except burgundy, bottle green black, ceramic glazed tiles ist quality 300 x 300 mm in all shades designs except white, ivory, fume red brown etc., powder coated ms butt hinges 100 mm x58 mm x 1.9 mm, stainless steel screws 50 mm, multi surface paint, acrylic exterior paint, special primer (c.w), vitrified floor tile 60x60 cm, water proof ply 12 mm thick, precoated galvanised steel plain ridges, 30 mm thick factory made glass fiber reinforced plastic panel door shutter i/c charge, high polymer modified quickset tile adhesive, solid block of size 40*20*20 cm, solid blocks of size 30x20x20cm, solid blocks of size 40x20x15cm, solid blocks of size 30x20x15cm, laterate stone of size 40x20x15cm, pvc pipe 15 mm outer dia 10kgf/cm2, anjili wood planks, pvc pipe 20 mm outer dia 12 kfg/cm2, pvc pipe 25 mm outer dia. 10kgf cm2, pvc pipe 50 mm outer dia 6kgf/cm2, pvc pipe 63 mm outer dia . 6kgf/cm2, pvc pipe 63 mm outer dia. 4 kgf/cm2, pvc pipe 110 mm outer dia 6kgf/cm2, pvc pipe 110 mm outer dia. 4kgf/cm2, pvc elbow 63 mm dia, pvc 45 degree elbow 63 mm dia, pvc bend 63 mm dia, pvc tee 63x63x63 mm dia, pvc door tee 63 x63x63mm dia, pvc vent cowl 63 mm dia, pvc socket/coupling 63 mm dia, pvc reducer 63x50 mm dia, pvc reducer 75x63 mm dia, pvc elbow 11

Central Government And Public Sector

CTN :37491172

03 Oct, 2024 NA

Lumding - Assam

Tender For supply of bolt hex head detailed description as per item 1 of the attached specification document , hex head bolt m20 x 100 detailed description as per item 2 of the attached specification document , bolt hex head detailed description as per item 3 of the attached specification document , high tensile hex head bolt detailed description as per item 4 of the attached specification document , stainless steel hex head bolt detailed description as per item 5 of the attached specification document , stainless steel hex head nut detailed description as per item 6 of the attached specification document , hex head bolt m16 x 45 class 10.9 , curtain runnner hook detailed description as per item 8 of the attached specification document , pneumatic impact gun detailed description as per item 9 of the attached specification document , 3 by 4 square drive detailed description as per item 10 of the attached specification document , pedestak grinder complete detailed description as per item 11 of the attached specification document , wd-40 chemical in aerosal can detailed description as per item 12 of the attached specification document , silicon sealant 260 ml cartidge make -dr.fixit or similar

Central Government/Public Sector

CTN :37514415

23 Sep, 2024 NA

Ahmedabad - Gujarat

Tender For supply of hex head bolt with thread m20,nominal length 50mm and property class 4.8, conforming to is- 13 63(part-1):2002/iso-4016:1999(4th revision) with hexagon nut with thread m20 and property class 5,conformi ng to is:1363 (part-3):2002/ iso-4034-1999 (4th revision). [ warranty period: 30 months after the date of deli very ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

Central Government/Public Sector

CTN :37511569

18 Sep, 2024 NA

Ratlam - Madhya Pradesh

Tender For supply of ht hex head bolt of size m22 x 55 (full threaded) as per is 1364 part 2 & 3 gra de 10.9 with plain washer to is 2016 & spring washer to is 3063 (similar to forbes). (one set consist of 3 items in 3 numbers). [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :37511457

20 Sep, 2024 NA

Chennai - Tamil Nadu

Tender For supply of hex head bolt m24x180-8.8 to is:1364 (part-i) 2002 and prevailing torque hexagon nut to size m 24 to specn is:7002-2005-8, zinc electroplated to gr.a3l of annexure e of is:1367 (part-eleven)2002. [ warran ty period: 30 months after the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

Central Government/Public Sector

CTN :37511838

15 Oct, 2024 NA

Chennai - Tamil Nadu

Tender For supply of hex head bolt m10 x 30 with spring washer and hex nut m10 to drg.no.rdso- 97005 item 7, 8 & 9 ms grade 4.6 [ warranty period: 30 months after the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

Central Government/Public Sector

CTN :37516296

23 Sep, 2024 NA

Salem - Tamil Nadu

Tender For supply of smc dt metering box in 63kva, box size dimensions- h=700mm, w=480mm, d=210mm, thickness of box= 3.5+-5%, color - off white, general tolerance- 10%+_. with internal accesories (200a 415v porcelain kit ket fuse 04nos). the meter box is crafted with anti corrosive, rust proof, dust proof, waterproof, uv protected and flame-retardant high-grade material that should have great dielectric adn mechanical strength properties. made out of moulding compound by process of hot press compressing moulding, confirming to is:13410.240x190x4 mm wooden board for fixing meter., 600x400x4mm hylam sheet for meter & fuse mounting,32mm pvc gland 03nos with dummy. removable frp angle for sheet mount, mbx40 gi earthing bolt with 02nut, 2 plain washer .1 spring washer. 20nos on both side with inside wire mesh, cable holding clamp -02nos outside. rubber gasket for waterproof. 04nos door closing clamp, foldable handle 1nos, , mszp box mounting flat 02nos per box. mszp pole clamp 02nos per box.. acceptable brand-epp, havells, l&t, c&s, indoasion, abb, hpl, sintex only.

Central Government/Public Sector

CTN :37514885

23 Sep, 2024 NA

Erode - Tamil Nadu

Tender For supply of set of spring washer (flat section type), set consists of 05 items as per is 3063 as given below; 1 . m12 - 100 nos/set 2. m16 - 100 nos/set 3. m18 - 50 nos/set 4. m22 - 100 nos/set 5. m30 - 100 nos/set. [ war ranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :37514531

23 Sep, 2024 NA

Lucknow - Uttar Pradesh

Tender For supply of stainless steel hex socket head cap screw m10x25 as per is:2269-2006 iso:4762 (a2-70 to is: 1367 pt.14-84), spring lock washer b10 as per is:3063-1994 with stainless steel nylock nut m10 as per is:70 02-2005 iso:7040 (a2-70 to is:1367 pt.14-84) as per drg.no.- ae61483 alt (l), item- 59,60,61. make- unbrako/ dfl/apl/star/sai only. [ warranty period: 30 months after the date of delivery ] ]

By Cities

By States

By Agencies

By Ownerships

By Sectors