Tender For supply of digital multimeter (q3) , handheld electric blower (q4) , pvc insulated copper cable single core and multi core circular sheathed with flexible conductor (v2) isi marked to is 694 (q2)
Tender For supply of 10 hp three phase monoblock openwell submersible pump set , 3 hp single phase monoblock pump set , 3 hp three phase borewell submersible pump set , single phase dol starter for 3 hp submersible and monoblock pump set , three phase fully automatic star delta starter for 10hp openwell submersible pump set , 3 core 6 sqmm flat pvc copper conductor , submersible safrty or support wire suitable for 5 hp submersible motor pump set , 63 mm diameter pe 100 hdpe pipe for water supply
Tender For tender for strengthening of existing 22kv ht line by providing additional pole, replacement of worn-out acsrconductor, patially damages insulators, , rejumppering etc. in electrical section reckong peo-ii under electrical sub division, hpsebl, recko
Tender For supply of 50 sq.mm, yellow colour electron beam irradiation curing process or chemical curing process thin walled flexible elastomeric cable with copper conductor suitable for rolling stock application conforming to rdso.spec.no.elrs/spec/elc/0019, rev.4,feb-2018,1.8 k.v. grade. note: (1) item/type/model/make/brand from the manufacturer/suppliers as approved by rdso shall only be considered. (2) cables shall be supplied in coils of 500 metres length, and left overquantity in multiples of 100 metres with a tolerance of +/-5% on the length. (3) firm shall indicate the curing process (e-beam irradiation (or)chemical curing) in their offer.
Tender For supply of 50 sq.mm red colour, electron beam irradiation curing process or chemical curing process thin walled flexible elastomeric cable with copper conductor suitable for rolling stock application conforming to rdso spec.no.elrs/spec/elc/0019, rev.4,feb-2018,1.8 kv grade. note: (1) item/type/model/make/brand from the manufacturer/suppliersas approved by rdso shall only be considered. (2) cables shall be supplied in coils of 500 metres length, and left over quantity in multiples of 100 metres with a tolerance of +/-5% on the length. (3) firm shall indicate the curing process (e-beam irradiation (or)chemical curing) in their offer.
Tender For rewinding of burnt up horizontal centrifugal vt motor repairing of vt centrifugal pumps of various capacities at surface water treatment plant kumarghat under dws sub-division kumarghat, unakoti tripura - rewinding of motor suitable v.t. pumps by complete dismantling including providing & rewinding with super enameled copper conductor (as per is:13730 part-3) conductor & all necessary spare parts and reassembling the same in/cl. servicing of rotor & necessary trial run as per specification and direction of the engineer-in-charge..i) 35 - 40 hp, ii) 50-65 hp, rewinding of horizontal motor suitable for centrifugal pumps by complete dismantling in/c providing & rewinding with super enameled copper conductor (as per is:13730 part-3) conductor & all necessary spare parts and reassembling the same including servicing of rotor & necessary trial run as per specification and direction of the engineer-in-chargei) 3.0 - 5.0 hp, ii) 7.5 - 10 hp, iii) 40 hp, repairing of centrifugal pumps by providing and replacing of impeller ( conforming to is : 1520 ) as per specification and the direction of the engineer-in-charge.a. c.i. impelleri) for 10000/15000 gph capacity., ii) for 20000/25000 gph capacity., b. bronze impelleri) for 10000/15000 gph capacity., ii) for 20000/25000 gph capacity., repairing of centrifugal pumps by providing and replacing of bush (sleeve) ( conforming to is : 1520 ) as per specification and the direction of the engineer-in-charge.a. ss / gm bush (sleeve)i) for 10000/15000 gph capacity., ii) for 20000/25000 gph capacity., b. c.i. bush (sleeve)i) for 10000/15000 gph capacity., ii) for 20000/25000 gph capacity., repairing of centrifugal pumps by providing and replacing of joining paper ( conforming to is : 1520 ) as per specification and the direction of the engineer-in-charge.i) for 10000/15000 gph capacity., ii) for 20000/25000 gph capacity., repairing of centrifugal pumps by providing and replacing of coupling ( conforming to is : 1520 ) with necessary fitting as per specification and the direction of the engineer-in-charge.i) for 10000/15000 gph capacity., ii) for 20000/25000 gph capacity., repairing of centrifugal pumps by providing and replacing of ball bearing ( conforming to is : 1520 ) as per specification and the direction of the engineer-in-charge.i) for 10000/15000 gph capacity., ii) for 20000/25000 gph capacity., repairing of centrifugal pumps by providing and replacing of ss shaft (ss-410) as per specification and the direction of the engineer-in-charge.i) for 10000/15000 gph capacity., ii) for 20000/25000 gph capacity., repairing of v.t. pumps by providing and replacing of g.m. bush for bowel (conforming to is: 1710) as per specification and direction of the engineer-in-chargei) for 20000/27,500 gph capacity v.t. pump., ii) for 40000/50000 gph capacity v.t. pump., repairing of v.t. pumps by providing and replacing of g.m. bush for suction case/ discharge case (conforming to is: 1710) as per specification and direction of the engineer-in-chargei) for 20000/27,500 gph capacity v.t. pump., ii) for 40000/50000 gph capacity v.t. pump., repairing of v.t. pumps by providing and replacing of rubber bush for bowel (conforming to is: 1710) as per specification and direction of the engineer-in-chargei) for 20000/27,500 gph capacity v.t. pump., ii) for 40000/50000 gph capacity v.t. pump., repairing of v.t. pumps by providing and replacing of ms lock (conforming to is: 1710) as per specification and direction of the engineer-in-chargei) for 20000/27,500 gph capacity v.t. pump., ii) for 40000/50000 gph capacity v.t. pump., repairing of v.t. pumps by providing and replacing of bronze impeller (conforming to is: 1710) as per specification and direction of the engineer-in-chargei) for 20000/27,500 gph capacity v.t. pump., ii) for 40000/50000 gph capacity v.t. pump., repairing of v.t. pumps by providing and replacing of ss shaft (ss-410) as per specification and direction of the engineer-in-chargei)