Tender For purchase of lab equipment for mechanical dept and electronics and communication dept - purchase of lab equipment for mechanical department and electronics & communication department specification (detailed in nit - ), mechanical department tail stock assemblymedium-duty tailstock assembly for dismantling & assembly, dc motor, hydraulic cylinder, hydraulic operated directional control valves (dcv, bearing with shaft assembly, coupling unit using driving and driven shafts using plummer block bearing unit, a).sliding mesh gear box for dismantling and assembling (b) constant mesh gear box cut section, electronics and communication department8051 micro controller kit, embedded trainer kit (using lpc2148), single phase induction motor, dth trainer kit, fiber optic communicationtrainer kit, sim reader trainer kit
Tender For supply of electronics equipment for ece - supply of electronics equipment for ece, dual output regulated dc variable power supplyas per specifications in annexure-i, function generator as per specifications in annexure-i, dso (digital storage oscilloscope) as per specifications in annexure-i, dc voltmeter analog (0-10) v as per specifications in annexure-i, dc ammeter analog (0-30) ma as per specifications in annexure-i, dc ammeter analog (0-100) ma as per specifications in annexure-i, dc ammeter analog (0-500) ma as per specifications in annexure-i, decade resistance box as per specifications in annexure-i, decade capacitance box as per specifications in annexure-i, decade inductance box as per specifications in annexure-i, strain gauge trainer kit as per specifications in annexure-i, temperature measurement kit as per specifications in annexure-i, ask modulation and demodulation kit as per specifications in annexure-i, dth trainer kit as per specifications in annexure-i, fiber optic communicationtrainer kit as per specifications in annexure-i, sim reader trainer kit as per specifications in annexure-i, fpga trainer kit as per specifications in annexure-i, fpga / soc development board as per specifications in annexure-i
Tender For supply of lab equipments - purchase of lab equipments, ask modulation and demodulation kitspecifications: message signal1: 8-bit variable data,amplitude 5v. message signal 2: debounced data, amplitude low (0) and high (5 v). message signal 3: fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz, amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. modulator type: switching modulator using analog switch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., fiber optic communicationtrainer kitspecifications:power supply: 230 v ac 10%, 50 hz mains operation. built-in regulated power supply. optical transmitters: led transmitter: 660 nm. optical receivers: phototransistor / pin photodiode receiver. built-in signal conditioning and amplifier circuits. audio power amplifier with speaker/headphone output. comparator / pulse shaping circuit for digital signal recovery. test points for cro observation and signal monitoring. fiber media: multimode plastic optical fiber (pof). fiber patch cords with connectors. signal sources: built-in sine wave generator. built-in square wave / digital pulse generator. voice signal input through built-in microphone/audio source. trainer features: separate transmitter and receiver sections. on-board test points for signal observation. led indicators for signal monitoring. fault simulation facility. compact tabletop modular design. circuit diagram printed on pcb. bandwidth: analog bandwidth: up to 350 khz. digital bandwidth: up to 2.5 mhz. controls: variable signal amplitude control. variable frequency control. optical intensity adjustment. standard accessories: patch cords and connectors. power cord. audio connecting cable. user manual.
Tender For auction sale of depot non ferrous scrap - scrapped s&t cables and hdpe ducts. (1)signalling cables copper -1.5sqmm(2c,4c,6c,8c) and 5c 2.5sqmm armoured copper cable. (2) telecom cables : copper telephone (20,50 and 200 pairs)clock pas cctv (co axial), power cables,fiber cables-fots (48 cores and it (6 cores). (3) hdpe ducts -40/50 sqmm dia of both signalling and telecom system. note: (i) minimum quantity to be lifted per day= 9 mt. (ii) total nos. of days for lifting complete lot= 04. i) this item comes under the category of hazardous and other waste and its sale shall be made only to an authorised actual user or authorised waste collector or an authorised disposal facility who have been authorised by state pollution control board/cpcb/ministry of environment, forest and climate change under hazardous and other wastes (management & transboundary movement) rules, 2016. therefore, participating bidders must hold valid authorization/registration certificate from spcb/cpcb/moefcc. this authorization/ registration certificate must be valid both at the time of bidding as well as at the time of lifting of material.ii) firm shall also submit a certificate/undertaking in regard to the total hazardous waste purchased/collected and processed for the current financial year till the time of auction.iii) original authorisation/registration certificate as well as the passbook issued to purchaser by spcb/cpcb along with authorization shall be required to be produced at the time of taking delivery. handing over of the hazardous and other wastes to the purchaser shall be only after making of the entry into the passbook of the purchaser by the depot officer of dmrc custodian.iv) the entire arrangement for transportation of the lot shall be made by the purchaser and the responsibility of safe transport of hazardous and other wastes as per provisions of hazardous & other wastes (management & transboundary movement) rules-2016 shall lie entirely on purchaser.v) the purchaser (receiver) shall also ensure the necessary authorisation for transport from concerned spcbs and this aspect shall be clearly stated in transport manifest (movement document) issued by department of dmrc handing over hazardous and other waste scrap to the purchaser. before taking delivery the purchaser shall submit documents/details to depot officer of custodian to show that (a) in case of transportation of hazardous and other waste for final disposal to a facility existing in a state other than the state where the waste is generated, he has obtained no objection certificate from the spcbs of both the states (b) in case of transportation of hazardous and other waste for recycling or utilisation including co-processing, he has given intimation to both spcbs (c) in case of transit of hazardous and other waste for recycling, utilisation including co-processing or disposal through a state other than states of origin and destination, he has given prior intimation to concerned spcb of states of transit.vi) the purchaser shall also ensure that the transport manifest system (movement document) for hazardous and other waste prepared by the depot officer of dmrc custodian as per provisions of hazardous waste management rules is followed. he will also give an undertaking that the relevant copies of the transport manifest (movement document) (as per colour code prescribed in the hazardous waste management rules shall be duly signed by him as well as by the transporter arranged/nominated by him and proper disposal of each signed copy of the transporter shall be ensured by him as well as by the transporter arranged/nominated by him for lifting the lot. also the acknowledgment copy of the transport manifest (blue copy) shall be provided by him to dmrc within 07 days of lifting a lot.