Get complete information related to latest Motor Pump Repair Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Motor Pump Repair Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Motor Pump Repair Tenders.
Tender For corrigendum : provn of 02 in nos bore wells alongwith associated items at icgs mundra - material and labour for drilling of 02 nos pilot/trial bore by direct rotary rig method including all t&p through any kind of starta (soil, kankar, boulder or soft or hard rock) down up to 150 m depth below ground level by using suitable drill bit according to levering of casing pipe including the cost of mud pit, channels, etc and disposal of soil obtained to a distance not exc. 1 km away complete all as specified. note:- (i) the drilling shall be continued up to specified depth and in case sticky clay occurs in between the drilling must be stopped and hydrologist of gws & sb shall be contacted & eggr-in-charge shall be informed.(ii)cost of this consultant shall be borne by contractor (iii) taking the samples from the bore well cutting for every 3 meter interval and every change in strata if less than 3meter. (iv) preparation of litho logs based on these samples.(v) drill time log to be prepared and prescribed., (vi) aquifer performance tests at constant discharge with draw down and recovery reading.(vii) after completion of pilot bore, the contractor shall have to arrange for electro eater logging test of each bore.(viii) contractor have also produced bore well water test report for drinking water parameters before levering of motor and pump.(note:- if water quality not found fit for domestic purpose use then all other connected items of trial bore will not be executed.) , supply assembling, jointing, lowering and fixing in the bore hole pvc casing pipe of nominal dia 315 mm (medium well) ,10 kg/cm2 working pressure, confirming to is 4985-2000 including providing pea gravel of 8 mm to 4.6mm size for packing around the casing/slotted pipe in bore well all as specified and directed. make: astral/ashirwad/ajay/sfmc, all as per item no 2.00 above but slotted pipe. , supply, assembling, jointing, lowering lead free pvc column pipes of nominal dia 65 mm, od 75 mm (min), non toxic, pressure 16 kg/cm2 with and including top and bottom adaptor (ss) and accessories like epdm ring and double ss stud all as spd and directed by engineer-in-charge. make: astral/ashirwad/ajay/sfmc, development of tube well with compressed air by means of air compressor of suitable capacity not less than 300 cfm and over pumping using suitable capacity pump to make available water free from turbidity complete all as specified and directed by engineer-in-charge., m & l for conducting yield test for the bore well by continuously pumping for 24 hours by using a submersible pump set to determine safe pumping yield and produced water test report of samples which is collect every hour complete as directed by the engineer-in-charge. [ all arrangements for yield test shall be made by contractor and cost for the same borne by contractor ], supply and fix ms reducer, bail plug, top cover made of 3mm thick ms plate for bore well in two half sections having a hole of 75 mm bore in centre to accommodate pvc pipe and submersible cable suitable for fixing to the pvc casing pipe top, electric logging and simple strata box including provision of 2 sets of ms clamps made of 50x6mm ms flat including nuts, bolts, etc. including one coat of epoxy primer and two coats of epoxy paint wherever necessary complete all as specified and directed by engineer-in-charge., supply, install, test and commissioning of submersible pump stainless steel body electric driven with submersible motor, water lubricate, 3 phase, 10.0hp (appx) 415 volts, 50 hz with suitable submersible electric motor suitable for discharge of 2 liters per second against total head of 125m in the bore complete all as specified and directed by the engineer-in-charge. [ note : column pipe, submersible cable and control gear will be measured and paid separately]. [make: kirloskar / crompton / ksb], supply, install, test and commissioning of submersible pump stainless steel body electric driven with submersible motor, wa
Tender For bid to ras supply of provision of misc items - synthetic enamel paint og , synthetic enamel paint black , synthetic enamel paint dark brown , synthetic enamel paint sand color , synthetic enamel paint brown , synthetic enamel paint white , synthetic enamel paint blue , synthetic enamel paint yellow , synthetic enamel paint green , synthetic enamel paint red , thinner , brush 2 inches , brush 4 inches , cement opc 43 gde , sand coarse , aggregate 20mm gde , white cement , fevicol , red oxide primer , oil bound distemper obd , screw full threaded 50mm 2 inches pack of 100 nos , nails full threaded 150mm , nails 100mm , nails 75mm , nails 50mm , nails 25mm , cgi sheet 3 feet x 10 feet , plywood 8 feet x 4 feet with 6mm thick , plywood 8 feet x 4 feet with 12mm thick , plywood 8 feet x 4 feet with 19mm thick , wooden scantling of size 50mm x 50mm , terracota , geru , sintex tank 1000 ltr capacity , floor tile 600mm x 600mm , floor tile 400mm x 400mm , floor tile 300mm x 300mm , 2 inch sds screw 50mm pack of 100 nos , 3 inch sds screw 25mm pack of 100 nos , termite solution , glass putty , urinal waste pipe 40mm , float valve 20mm , wiremess for door or window , led tube light fitting 9 to 10 w , led tube light fitting 18 to 20 w , led bulb 7 to 9 w , led bulb 10 w , led bulb 12 w , multistranded copper cable of size 1 point 5 sqmm , multistranded copper cable of size 2 point 5 sqmm , casing n capping 25mm , mcb spn 40a dp , pt switch 5a , piano type switch 15a , socket 5a , socket 15a , ss combination 5a with box , ss combination 15a with box , flexible wire twin twisted , mcb 2 point 5 amps , mcb 6 to 32 amps , pvc gang box 2 way , pvc gang box 4 way , pvc insulation tape 15mm , bulk head fitting , mcb spn 32 amps , membrane cleaner 11 , membrane cleaner 22 , membrane cleaner 33 , cartridge filter eliment , cartridge filter 20 inch , raw water pump , membrane
Tender For supply of submersible pump 20 hp elect driven 415v suitable for 250mm dia bore well , casing pipe size 300mm , submersible pump 25 hp elect driven 415v suitable for 250mm dia bore well , casing pipe size 300mm for 25 hp , ms erw pipe 100mm dia both side flange ms pipe including nuts and bolts
Tender For supply of various spares for flowmore make centrifugal pump - brg housing outboard , cover brg hsg , wearing ring casing , impeller , key impeller , gasket for shaft sleeve , shaft sleeve , stuffing box bushing , mech seal assy , seal cover or housing , o ring , sleeve nut and lock nut for sleeve de , brg housing inboard , pump shaft , water deflector , sleeve nut and lock nut for sleeve nde , o ring shaft to shaft sleeve , wearing ring impeller , flexible coupling spacer type bid number/ ( ( ) ): gem/2024/b/5473385 dated/* : 12-11-2024 bid document/ 1 1 / 23
Tender For corrigendum : supply of spare for ksb make model bfp - chtc3 by 16 stage casing 1 by 2 by 3 , chtc3 by 16 stage casing 5 , chtc3 by 16 stage casing , chtc3 by 16 stage casing 11 by 13 by 14 , chtc3 by 16 last stage casing , chtc3 by 16 inlet ring , chtc3 by 16 diffuser , chtc3 by 16 last stage diffuser , chtc3 by 16 spacr sleeve 525 point 03 , chtc3 by 16 brg point housing 350 point 01 , chtc3 by 16 brg point housing 350 point 02 , chtc3 by 16 brg point end cover , chtc3 by 16 o ring and gskt set , chtc3 by 16 labyrnth ring , wk125 by 6 bearing housing , wk125 by 6 brg cover de , chtc3 by 16 casing wear ring 502 point 01 , chtc3 by 16 imp wear ring , chtc3 by 16 spacer ring 504 point 01 , chtc3 by 16 spacer ring 504 point 02 , chtc3 by 16 retaing ring 506 point 02 , chtc3 by 16 thrower , chtc3 by 16 spacr sleeve 525 point 01 , chtc3 by 16 spacr sleeve 525 point 02 , chtc3 by 16 intrstg bush , chtc3 by 16 stage bush , chtc3 by 16 bal disc seat , chtc3 by 16 balance drum , chtc3 by 16 lubrication ring , chtc3 by 16 shaft nut , chtc3 by 16 bearing shell , wk125 by 6 brg cover nde , wk125 by 6 bush discharge casing , wk125 by 6 bush suction casing , wk125 by 6 interstage bush , wk125 by 6 ring , wk125 by 6 casing wear ring , wk125 by 6 impeller wear ring , wk125 by 6 stage sleeve , wk125 by 6 spacer sleeve suction , wk125 by 6 spacer sleeve discharge , wk125 by 6 clamping sleeve , wkt50 by 06 adapter , wkt50 by 06 drive shaft , wkt50 by 06 brg point housing , wkt50 by 06 brg point cover , wkt50 by 06 split ring , wkt50 by 06 wear ring , wkt50 by 06 stage wear ring , wkt50 by 06 impeller wear ring suc , wkt50 by 06 wear ring suction , wkt50 by 06 stage sleeve , wkt50 by 06 centring sleeve , wkt50 by 06 brg point sleeve ps , wkt50 by 06 brg point sleeve sd , wkt50 by 06 brg point sleeve ds , wkt50 by 06 stage bush , wkt50 by 06 brg point bush disch , wkt50 by 06 brg point bush suc , wkt50 by 06 brg point bush adptr , wk125 by 6 suction casing , wk125 by 6 discharge casing , wk125 by 6 stage casing , wk125 by 6 diffuser suction , wk125 by 6 diffuser , wk125 by 6 impeller , wk125 by 6 shaft , wk125 by 6 shaft nut , wk125 by 6 impeller key , wkt50 by 06 suction casing , wkt50 by 06 1st stg casing , wkt50 by 06 stage casing , wkt50 by 06 suction diffuser , wkt50 by 06 diffuser , wkt50 by 06 stage impeller , wkt50 by 06 suction impeller , wkt50 by 06 conical coupling , wkt50 by 06 deflector , chtc3 by 16 chtc 3 by 16 segmental ring , wk125 by 6 wk125 by 6 set of gasket , wkt50 by 06 wkt 50 by 06 set of gasket , wkt50 by 06 wkt 50 by 06 set of parallel key , chtc3 by 16 chtc 3 by 16 set of hexa nut , chtc3 by 16 chtc 3 by 16 set of grub screw , chtc3 by 16 thrust bearing 314 , chtc3 by 16 thrust bearing p 384 , wk125 by 6 cooling chamber cover , wk125 by 6 thrower , wk125 by 6 coupling assembly , wkt50 by 06 oiler , wkt50 by 06 pump shaft
Tender For corrigendum : supply of vibrobit make sensors and accessories - rotor vibration sensor, make - vibrobit, model - dvt10-160- 0,5 , vibrobit make ip37 b-05 slash 2-7 -rotor vibration convertor. , cable for vibrobit make rotor vibration sensor cable length -7m , bearing vibration sensors along with amplifiers, range- 0-15 mm slash s, make- vibrobit, model dpe23mvb, output range-4-20ma, sensor cable length 5.0m , rotor expansion sensor, make- vibrobit, range 0-16 mm, model- dvt 60.20-5 , secondary converter for rotor expansion sensor in hp turbine, range 0-16mm, make vibrobit, model- ip34-b-16-60-5 , rotor expansion sensor in lp turbine, range 0-25mm, make- vibrobit, model- dvt 40.20-7 , secondary converter for rotor expansion sensor for lp turbine, range 0-25mm, make- vibrobit, model- ip42- b-25-25-7 , rotor expansion sensor in lp turbine, range 0- 45mm, make - vibrobit, model- dvt 40.30-7 , vibrobit make dvt82, along with b.50 -casing expansion sensor along with scale and convertor , speed sensor, make - vibrobit, model - dvt30-0.5, range 0-4000 rpm , cable for vibrobit make speed sensor cable length - 5m , eddy current trip striker sensor, make - vibrobit, model - dvt 43.40x7 , convertor, make - vibrobit, model - k21- 0.5-7 for vibrobit make eddy current trip striker , vibrobit make dvt82, along with b.160. hp control valve position transducer along with scale and secondary convertor. , casing expansion sensor, make- vibrobit, model- dvt 82-b-50 , speed indicator, make - vibrobit, model - e n22 , range - 0 - 4000 rpm , power limiter with converter and integrated cable , make - vibrobit, model - no.b.100. scale 120 , axial shift sensor with ss316 of standard probe length - dim-38mm. model - dvt20-40-0.5 , axial shift sensor of probe length dim-50mm makevibrobit.model dvt20-50-0.5 for feed water pump , vibrobit make ip34 b-04-20-5 - secondary convertor for axial shift sensor. , connecting cable of length -7m for axial shift sensor. model - kc10 , 220v dcto24v dc converter module for axial shift sensor-item 20 feed water pump axial shift.model - built in converter - model ip34 b04- 20-5. , sealing device 9.042 make- vibobit. model- m24 , cable 9.057 make- vibrobit. model- kc10-7 , cable 9.157 make- vibrobit. model- kc11-7 , connector 9.048 make vibrobit. model- kp10 , connector 9.049 make- vibrobit. model- kp20 , converter 9.129 make- vibrobit. model- kp23- pp , installation mechanism 9.044 make- vibrobit. model my10 , installation mechanism 9.144 make- vibrobit. model my11 , test rig 421412.047 make- vibrobit. model- cp10 , adjuster equipment 421412.174 make - vibrobit model ph11 , test rig - make - vibrobit, model - cp20 , portable vibration-testing machine make - vibrobit. model - bcb-131
Tender For providing of custom bid for services - 200138128 service contract for 500 mw condenser vac pump impeller and casing repairment for ntpc farakka