Tender For tender for supply of supply of twin core shielded microphone cable (red & black) each core shall be of 23/36 swg pvc insulated copper conductor in over all pvc jacket of reputed make like delton, finolex, asian, hevells, molex, furutech, supply of lan meter make: fluke or jdsu or vivex or better as per specification attached., supply of optical line interface card (sot-18) for tejas tj1400 make stm equipment without sfp's compatible to tejas stm installed in rtm division. accepted make/brand: tejas networks, supply of factory crimped cat6 u/utp patch cord 3.0 mtrs length of reputed make as per specification, supply of opticd visual fault locator (laser source meter). tourch type.laser power output 30mw.suitable to measure 30km length of ofc cable. universal connector to match sc, fc, lc and st connector to match sc.fc.lc and st connector suitable pouch, supply of mcb 6a, 2pole, 240v ac (type-c) conforms to iec 60947-2. miniature circuit breakers as per is: 8828/ moulded case circuit breaker as per is:13947/182 or iec: 60947-2, for higher current ratings. make: schneider, siemens, havells, l&t, legrand, supply of 16 amp double pole mcb make havells, anchor, siemens, finolex, orient or similar, supply of optical laser source (supporting 1310/1550 nm with fc/sc connectors, power supply adapter/in built battery) as per technical specification, supply of pvc flexible pipe 1 inch dia in roll grey colour suitable for electrical use confirming to is:6946:1973 make duroflex, finolex, precision, legrand or superior, supply of tmc dp box for 100 pair with krone modules along with mounting arrangement as per specification attached, supply of rj45 cat 6 information outlet box, optical power meter (mw)with visual fault locator as per specification make-vaivi/stanlay/exfo, supply of telephone instrument as per specification
Tender For supply of soldering irom , soldering stand , small screwdriver , wire cutter , hacksaw , extension board , ic tester machine , digital voltmeter for bread board , digital ammeter for bread board , scientific calculator , battery connector of bread board , jumper wire male to male , bread board wire , a to b cable , usb male to female cable , pcb for soldering practice , perforated pcb , bread board , bread board power supply , mercury vapour lamp , sodium light bulb , green laser light , red laser light , ppt pointer , ic 7400 nand , ic 7402 nor , ic 7404 not , ic 7408 and , ic 7410 triple 3 input nand , ic 7432 or , ic 7486 xor , ic 7474 dual d flip flop , ic 7478 jk flipflop with clear and preset , ic 7430 8 input nand , ic 74266 quad xor and nxor with open collector outputs , ic 741 op amp , ic 358 dual op amp , 555 timer , ic 7805 voltage regulator plus 5v , ic 7905 voltage regulator minus 5v , ic 317 adjustable voltage regulator , uln 2803a darlington transistor array , dac mcp4921 digital to analog convertor , comparator generic or specific ic , multiplexer , demultiplexer , 16 pin ic casing , 8 pin ic casing , cnc shild for arduino , rotary encoder for arduino , current sensor for arduino , photo diode , tracing paper , insulation tape , hand wash refile , 256 gb pen drive , mouse pad , chart paper different color , scale plastic 12 cm , eva sheet a4 different color , pencil , paper cutter , small electric motor , cycle walto , set square both type small size coloured , a3 size drawing sheet , joot rope , a4 size drawing sheet , pen drive , hdmi to vgi connector , a4 size different colour sheet , black sheet , oil pastel colour , collered pencil , pastel pencil different colour , loose pebbles different colour , marble , plastic or wooden sticks 12cm height each , 3d shapes different size , seizer big size , seizer small size , mirror , scrap paper big size , scrap paper small square size , forex sheet 2x2 feets , office bag , water dispenser , first aid kit , hats , gents shoes , sari of various states marathi south indian assami kolkata , mop and backet , doormat soldering irom specification not available, soldering stand specification not available, small screwdriver specification not available, wire cutter specification not available, hacksaw specification not available, extension board specification not available, ic tester machine specification not available, digital voltmeter for bread board specification not available, digital ammeter for bread board specification not available, scientific calculator specification not available, battery connector of bread board specification not available, jumper wire male to male specification not available, bread board wire specification not available, a to b cable specification not available, usb male to female cable specification not available, pcb for soldering practice specification not available, perforated pcb specification not available, bread board specification not available, bread board power supply specification not available, mercury vapour lamp specification not available, sodium light bulb specification not available, green laser light specification not available, red laser light specification not available, ppt pointer specification not available, ic 7400 nand specification not available, ic 7402 nor specification not available, ic 7404 not specification not available, ic 7408 and specification not available, ic 7410 triple 3 input nand specification not available, ic 7432 or specification not available, ic 7486 xor //bid details2 / 62
Tender For corrigendum : supply of restoration deicing system of spillway radial gate 1 and 2 trashrack repairing servicing at cps - wall plate heater 16 kw 415 v ac length 7600 mm , skin plate heater 16 kw 415 v ac length 6825 mm , trunion arm heater 3 kw 240 v , cover plate heater 3 kw 240 v , cover plate heater 4 kw 240 v , cover plate heater 2 kw 240 v , thyristor power controller three phase current rating 50 amp , thyristor power controller single phase current rating 50 amp , thyristor power controller single phase currnet rating 40 amp , thyristor power controller single phase current rating 20 amp , temperature controller aux supply 203 v ac input 4 to 20 ma , rtd pt 100 sensor od-6 mm x l50 mm with 1 meter cable with mating connector. , propylene glycol gel industrial grade , hardware items viz. nut bolt washer water tight joint kits for cable heater tubes joints etc , installation testing and re commissioning of deiceing system of spillway radial gates no 1 and 2 and trash rack installed at dam of chutak power station as per the scope of work , annual maintenance contract two visits per year of service engineer for 5 service days for two persons including travelling charges , transportation packing and forwarding
Tender For corrigendum : manufacture, fabrication, supply,erection, testing and commissioning with 1x8 mva pr.tr,stn transformer, associated equipments, accessories, control panels, control room and electrical works at o.krishnapuram in trichy metro under tkc thro e tener - electrical material supply, power transformer 33/11kv, 8mva power transformer with oltc, breaker along with ct for outdoor ss 33 kv (gc) vcb (out door) 1250a, 26.3ka per 3 sec., 3 pole gang operated soild dielectric insulated with permanent magnetic actuator operating mechanism with inbuilt vcb bushing embedded dry type epoxy resin cast ct (600-300/1-1a) with structure and complete accessories with breaker platform., 11kv (lv) vcb (out door) 12 kv, 1250a, 26.3ka per 3 sec., 3 pole gang operated soild dielectric insulatedwith permanent magnetic actuator operating mechanism with inbuilt vcb bushing embedded dry type epoxy resin cast ct (1200-600/1-1a) with structure and complete accessories with breaker platform., 11kv (feeder) vcb (out door) 12 kv, 1250a, 26.3ka per 3 sec., 3 pole gang operated soild dielectric insulated with permanent magnetic actuator operating mechanism with inbuilt vcb bushing embedded dry type epoxy resin cast ct (400-200/1-1a) with structure and complete accessories with breaker platform., potential transformer 33kv potential transformer with tc (single phase unit), 11kv potential transformer with tc (three phase unit), panels ac panel for 33kv ss, 110 v dc annunciation panel type b, 110v dc indoor c&r panel for gc breaker, 110v dc indoor c&r panel for lv breaker, 110 v dc indoor c&r panel for twin feeder, control cables, junction box and accessories 14c x 2.5 sq.mm copper cable armoured, 8c x 4 sq.mm copper cable armoured, 4c x 4 sq.mm copper cable armoured, 4c x 2.5 sq.mm copper cable armoured, 2c x 2.5 sq.mm copper cable armoured, isi mark 19 / 22 mm cable gland as directed by the field engineer., isi mark 25 mm cable gland as directed by the field engineer., isi mark cable 28 mm gland as directed by the field engineer., lugs, ferrules, sleeves, cable tie, insulation tape and other accessories for providing cable core end termination, supply of gi chequerred plate 6mm thickness, junction box supply of ct/pt junction box made out of 14swg (2mm) m.s.sheet wherever required as directed by the field engineer. the box shall be vermin proof shall have sturdy hinges, provision for mounting terminal blocks and locking arrangements including cost of all materials. 400w x 300h x 150d, supply of ac junction box of size 535x310x127mm of 18swg ms sheet including hrc fuse unit-18 nos. should be fitted with base, consumables etc. (the box shall be vermin proof, shall have sturdy hinges and locking arrangements), supply of mounting channel suitable for cbtm 5 terminal block in panel /box as required and as directed by the field engineer., supply of disconnected type terminal block suitable for ct circuits in panels/ box as required & as directed by the field engineer, supply of isi mark bakelite hrc fuse holder with fuse of 2/5/10/16 amps reputed make in panels/ boxes for ac/dc/pt circuits wherever required as directed by the field engineer. 16 amps - fuse holder with hrc fuse, 63amps - fuse holder with hrc fuse, bus & bus materials zebra acsr conductor, 2.0" / 50 mm aluminium bus bar (thickness:5 mm), 22/33 kv pt insulators, 11kv pt insulator, 11kv, 120kn disc insulators (antifog), strung bus eye bolt of 18 - 20 mm dia gi rod of required length suitable for 33kv, 22kv and 11kv strung bus including cost of gi rod and 2nos gi nuts & washer as directed by the field engineer., clamps and connectors tension fitting clamp 4 bolted for zebra, t clamp for 2" bus to single zebra, t clamp for zebra to zebra, switchend clamp for single zebra, switchend clamp for 2" busbar, reducer clamp for 2" bus to zebra, pg clamp for zebra, free end clamp for 2"busbar, corana bell for 50mm bus bar, switch end clamp for mink, seating block for 2" bus bar(for g
Tender For supply of point machine and variouse other items as per boq attached inspectioon rdso rites consignee - supply of point machine irs type 220 mm stroke clamp type as per irs s$-24/2002 (amendment 1) or latest.(inspection agency:- rdso), supply of q-series led ecr (universal type i.e.qecx-61), 4f/4b complete with plug board(base plate), connectors, retaining clips etc. and conforming to brs: 941a sts / e / relays / ac lit led signal / 09 - 2002, amdt.-1 or latest and rdso spec.no.irs: s - 34, s- 23 or latest, as applicable. the interlocking code for this unit shall be "abdhk". (inspection by rdso)., contactor unit (qbca1 type), 24 v dc, 2hf / 4b complete with plug board (base plate), connectors, retaining clips etc and conforming to brs- 943 and rdso specn. no. irs : s - 34, s- 23, s - 60 or latest, as applicable. th e interlocking code for this unit shall be "bcejk". (inspection by rdso)., q-series magnetically latched neutral line relay (ql1 type), 11f / 4b, 24v dc complete with plug board (base plate), connectors and retaining clips and con forming to brs-935a and rdso specn. no.irs : s - 34, s - 23 or latest, as applicable. the interlocking code for this unit shall be "abdeg.(inspection by rdso)., supply of basic material to construct unit maintenance free earth as per rdso specs. no. rdso/spn/197 ver. 1.0 or latest to achieve a resistance less than 1 ohm. it consist of following:(a) copper bonded steel electrode of minimum 3.0 meter long, minimum 17.0 mm dia with copper bonding thickness of minimum 250 microns and ul listed and marked = 1 no. (b) earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. (c) copper strip of 150x25x6 mm, to terminate earth rod = 1 no. (d) copper strip of 300x25x6 mm (meeb) = 1 no. (e) copper strip of 150x25x6mm (seeb) = 1 no. (ii) supply of 35 sq. mm multi strand single core pvc insulated copper cable as per is: 694 for connecting main earth electrode to meeb in the equipment room in duplicate. (minimum 10 meter.) (iii) supply of 16 sq. mm multi strand single core pvc insulated copper cable as per is: 694 for connecting meeb to seeb and spd to meeb (minimum 10 meter.) (iv) supply of 10 sq. mm multi strand single core pvc insulated copper cable as per is: 694 for connecting various equipments to seeb (v) supply of copper lug sleeve for 3/16 cable.(inspection by consignee)., supply of master telephone with voice logging facility for electronic lc gate telephone system as per specification no: rdso/spn/tc-51/2011 revision 3.0 with amendment no. 1 or latest. (inspection by rites)., electronic lc gate slave telephone system with voice recorder as per rdso specification no. rdso/spn/ tc/51/2021 revision 1.0 (inspection agency:- consignee), supply of centralized power supply system 24 volts dc power pack with 7ah mf battery for electronic lc gate telephone system as per rdso spec:- no. rdso / spn / tc / 51 / 2011 (rev. 3.0) amdt - 1 or latest.(inspection agency:- consignee), supply of optical power meter, type-b, as per tec spec. gr / opm - 01 / 03 feb. 2005 or latest. (make & model khushicom-k280) or similar branded make. (inspection by consignee)., supply and testing of optical laser light source of make- jdsu model- ols-35 or similar branded make.(inspection agency:- rites), supply of optical laser torch of reputed make. (make & model-proskit mt-7530) or similar branded make. (inspection agency: - consignee), supply of automatic fusion splicer for single mode optical fibre cable, along with accessories as per tec spec. tec/gr/tx/osm 001/04/sep-12 or latest of make superior/fujikura or similar. consignee shall approve the supply only after successful demonstration at site. (inspection agency:- rites), supply of otdr suitable for 1310/1550nm fiber with resolution of 60 cm, dynamic range of 314/29 db with all accessories for working on single mode optical fiber as per tec spec. tec/gr/tx/otd 001/05/sep-19 or latest, of reputed make like yokogawa/zdsu/viavi or similar. cons
Tender For supply of procurement of coaxial-to-waveguide adapter, 1. 0 mm(m) to wr-10 , procurement of rf adapters - between series 1. 0 mm-female to wr10 ug387/u flange waveguide coax adap , procurement rf connectors / coaxial connectors 1. 0mm f panel end launch jack 110 ghz
Tender For repair maint of ht electric supply network system replacement of unserviceable ht ug cables maintenance and upkeep of ht control gears,vcbs rmus transformers acbs ht joints and fault finding ht panels and miscellaneous connected itmes