Latest angle iron Tenders | Government angle iron Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government/Public Sector

CTN :43521556

31 Jan, 2026 NA

Multi City - Multi State

Tender For supply of pin multiplug socket with 2 output , batten holder , porcelain holder , bell ding dong , water pump for desert cooler , 4 way sp single door distribution board in metal , fiber and plastic body exhaust fan with dimensions 200mm speed , fan clamp , 8 fan sheet , pvc round sheet , 6 amp 2 way gang box 1switch 1socket , 16 amp 2 way gang box 1switch 1socket , 6 amp 1 way gang box 1switct , 6 amp 1 way gang box 1 socket , bearing 6201 , bearing 6202 , 1.5 pvc gitties , 1,2 4 head black screw , 1 4 head black screw , 1,2 machine screw , 3,4 machine screw , 1.5 machine screw , 2 machine screw , 2.5 machine screw , pvc tape 7.5 meter , 3by4 pvc conduit pipe make like - astral,diplast,polypack , 3by4 pvc bend make like - astral,diplast,polypack , 3by4 pvc junction box make like - astral,diplast,polypack , 1 pvc conduit pipe make like - astral,diplast,polypack , 1 pvc bend make like - astral,diplast,polypack , 1 pvc junction box make like - astral,diplast,polypack , 1 gi clamp , 1 pvc tee , 40 mm pvc conduit pipe make like - astral,diplast,polypack , 40 mm pvc bend make like - astral,diplast,polypack , 40 mm pvc junction box make like - astral,diplast,polypack , 2 sq.ft.4 sq ft. bakelight sheet , 6 sq mm ring type copper thimble , 6 sq mm pin type copper thimble , 16 sq mm ring type aluminum thimble , 25 sq mm ring type aluminum thimble , 400 sq mm ring type aluminum thimble , 240 sq mm inline type aluminum thimble , 400 sq mm inline type aluminum thimble , 1 flexible pipe , pcb board of 1200mm,1400 mm ceiling fan make super fan , bearing 6001 , bearing 6205 , 2.5 mfd capacitor , 3.15 mfd capacitor , 4.0 mfd capacitor , 4.0 mfd capacitor oil type , outdoor ac aluminium grill jali size-24inch24inch , 3,4 self screw , 12-18 watt led bollard pathway,garden light-warm white , 2.0 core x 10 sq mm pvc aluminium cable , 2 core x 16 sq mm pvc aluminium armoured cable , 4 core x 16 sq mm pvc aluminium armoured cable , 4 core x 16 sq mm pvc copper cable , 7 into 5 wooden box , 8into5 wooden box , 10into5 wooden box , 7into5 bakelite sheet , 8into5 bakelite sheet , 10into5 bakelite sheet , gulmekh iron , ultra fast rechargeable batteries charger for aa and aaa , 1 phase electric energy lcd digital meter 0-40 amp capacity , 3 phase electric energy meter with capacity 10- 60 amp , single phase digital engery meter with kw , 3 phase direct measuring energy meter , supply of 3-phase, 3 wire, ac voltmeter with voltage , supply of 3-phase, 3 wire, ac ampere meter , 3 phase 4 wire ,5amp. voltage range 230 , current transformer ratio 300 , digital mega ohmmeter, insulation resistance tester , digital clamp meter ,with range of 40a,600a ac , crc spray, 2-26 grade of 500 ml. , electrical insulation spray of 400 ml in red composition , aluminium oxide sand paper 80mm width , thinner for cleanig electrical conductors , bell switch one way piano type make- havells,anchor, vinay , single phase meter pvc transparent box , three phase meter pvc transparent box , mastic tape , 63 amp sliding terminal contact block for 1.5-10 sq mm in polyamide material , desert cooler water pump , 16 kg copper winding demolition hammer with 1600 watts power,220volt inpu , 150 watt hot glue gun with 20 glue stick , set of screw driver with minimum 6 screw driver head , tool kit with electrical impact drill with of 3000rpm , 100 watt rechargeable led flood lights , multipurpose pu foam of 700- 800 ml capacity , rotary hammer drill machine power,220volt input , angle grinder with 900watt motor,100mm disc , professional air blower equipped with //bid details 2 / 114 650watt , 400 amp 3 phase 4 pole manual changeover switch , 1,2 pvc water pipe , heavy duty foldable step ladder-5 step powder coated stee , double side silicon tape heavy duty transparent with strong adhesive , double side foam tape with strong adhesive

State Government

CTN :43496843

16 Jan, 2026 21.23 Lacs

Bengaluru - Karnataka

Tender For tender for the procurement of irdm & mechanical sector toolkits for sc & st trainees - tlk-safety helmet , tlk-safety apron, tlk-tool kit box , tlk-triangular file 2nd cut, tlk-multiple slip joint plier, tlk-hammer ball peen , tlk-hacksaw frame , tlk-lineman plier, tlk-tlk-file flat 2nd cut, tlk-file flat bastard, tlk-file flat smooth, tlk-file half round 2nd cut, tlk-center punch , tlk-chisel cold flat, tlk-c clamp, tlk-digital multimeter, tlk-double ended spanner, tlk-engineer try square, straight shank twist drill bit set, tlk-auto-darkening welding glasses, tlk-adjustable spanner, tlk-angle grinder, electrician screw driver , hand drilling machine electric portable , hexagonal allen key set , needle files , neon tester , tlk-combination plier, tlk-file square 2nd cut, tlk-steel rule , tlk-welding hand gloves, heavy duty screw driver

CTN :43206566

12 Jan, 2026 NA

Ferozepur - Punjab

Tender For corrigendum : material and labour for construction of 3800 mtr x chain link fence in ferozepur - s&f structural steel post of angle iron 65x65x6mm, 4.50 mtr long, weight as per is 2062-1984 including fabrication of 0.60 mtr both side long top portion swan neck v type at 30 degree to vertical, including making six round holes of 15 mm dia on vertical posts and for fixing of nuts and bolts and three nos of 15 mm dia holes for fixing strut and five nos notches on the swan neck and welding of two nos of 16 mm ms rod each of 0.23 mtr length to bottom end of picket for anchorage including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above gl complete and two coat of bituminous paint embedded portion of angle 0.45mtr. make : jindal/ sail/ tata/equivalent isi marked complete all as specified and directed by engineer-in-charge, s&f structural steel post of angle iron 65x65x6mm, 3.30 mtr long, weight as per is 2065- 1984+b12, including fabrication for strut post bending at top portion, including making three nos holes of 15 mm dia on vertical posts for fixing of nuts and bolts and three nos of 15 mm dia including 0.23 mtr 16 mm dia ms rod two piece to be welded at bottom for anchoring purpose including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above gl complete and two coat of bituminous paint for stud 0.45mtr below gl for one side of the post complete all as specified and directed by engineer-in-charge. make : jindal/ sail/ tata/equivalent isi marked, s&f galvanised two or three strand steel barbed wire (line wire) of 2.24mm diameter of wire, barbs at 75mm spacing. the barbs are (point wire) 02mm thick wire shall be isi marked as per is:278 of 1978 (third revision) with amdt no 1 to 4. the points of barbs shall be sharp. the line and point wires shall be circular in section free from scales and point wires shall be circular in section free from scales and defects and shall be uniformity galvalium. the barbed wire shall be manufactured as per clause 11.2.1 and 11.2.2 respectively of is specification cited above read with is 4826/79 (first revision).make:sail/tata/ aplapollo/rinl/jsw complete all as specified and directed by engineer-in-charge, s&f galvanised steel chain link fence fabric of mesh size 125mm x 125mm (+/-) 4mm of 4.00mm nominal diameter. the size of chain link fence fabric shall be 2.7 mtr x 15 mtr mesh wire. galvalium chain link shall be manufactured as per is 4823 complete all as specified and directed by engineer-in-charge. make : tata/jsw/rinl/ jindal/sail., s&f ms plat of 40x3 mm, 2.70 mtr long with 6 holes of 15 mm dia, including one coat of red oxide primer and two coats of synthetic enamel paint. 3.02 kg per flat. make of steel: jindal/ sail/ tata/equivalent isi marked complete all as specified and directed by engineer-in-charge., s&f mild steel bolts with hexagonal head at one end and screwed the other end fitted with one nut and two washers. the bolts shall be 12mm dia and 50mm long. strong long lasting, resistant to corrosion and 100% recyclable complete all as specified and directed by engineer-in-charge. make: jindal / sail/ tata/ apl apollo/ jsw/ rinl, s&f ms round bars 10mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer. make: jindal/ sail/ tata/ apl appolo/ jsw/ rinl complete all as specified and directed by engineer-in-charge., s&f ms round bars 16mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer make: jindal/sail/tata/apl apollo/jsw/rinl complete all as specified and directed by engineer-in-charge., material and labour for excavating in soft and dense soil trenches, exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m in dept

CTN :43519536

19 Jan, 2026 NA

Multi City - Multi State

Tender For supply of mild steel angle iron 50x50x6mm , fibre sheet vulcanized 1.2mm thick (4'x8') size , elect rod welding steel mild g/p 3.15mm , bolt bsw s/b u/m hex hd with hex nut 1/4" x 3/4"

CTN :43521888

20 Jan, 2026 NA

Multi City - Multi State

Tender For supply of angle iron , cgi sheet , photo frame , flex map , voltas air cooler , flex for screen , water bottle 20 lt , camera fesh , flex banner 8x6 , flex banner 10x7 , matting graphics , therma cool , construction of toilet , plumbibg and labour charges , quarter plate , full plate , badmenton , plt sheet , iron cutter blade

CTN :43502482

23 Jan, 2026 NA

Osmanabad - Maharashtra

Tender For supply of for training , providing and supplying of halogen lamp set with stand for illumination of solar panels in lab ac mains operated to provide 0 to 1000 watts per meter square , providing and supplying of motorized bench grinder ac mains operated , providing and supplying of battery charger 0 6 9 12 24 48 v 30amp , providing and supplying of solar photovoltaic module set 75 w mono crystalline module 75 w amorphous silicon module 250 w thin film module 5w 10w 40w poly crystalline module set of , providing and supplying of solar panels 250 wp , providing and supplying of solar charge controller with dusk to dawn automatic switching 12v 10a , providing and supplying of solar charge controller with manual switch day lighting 12 v 10 a , providing and supplying of array junction box for connecting 250w x 4 nos solar panel with dc fuse dc mcb and surge suppressor protection , providing and supplying of solar lantern led type , providing and supplying of solar lantern cfl type , providing and supplying of solar lantern assembly sets , providing and supplying of home light system 12 v dc with fm receiver led bulb and mobile charger as loads , providing and supplying of solar cell kit , providing and supplying of clinometer for angle measurement , providing and supplying of spirit level for floor level check , providing and supplying of anemometer for wind speed measurement , providing and supplying of dc table fan 12 v , providing and supplying of ac voltmeter mi 0 , providing and supplying of volt meter 0 30v , providing and supplying of volt meter 0 100v , providing and supplying of ammeter mc 0 1a , providing and supplying of ammeter mc 0 5a , providing and supplying of ammeter mc centre zero 0 20a , providing and supplying of ammeter mc centre zero 050a , providing and supplying of power factor meter , providing and supplying of rheostat set 0 1 ohm 5 amp 0 10 ohm 5 amp 0 25 ohm 1 amp 0 300 ohm 1 amp set , providing and supplying of ac energy meter single phase 10 a 240 v inductiontype , providing and supplying of ac energy meter three phase 15 a 440 v induction type , providing and supplying of kilo wattmeter analog 0153kw pressure coil rating 240v440v current rating5a10a analog portable type housed in bakelite case , providing and supplying of digital wattmeter 230 v 1 kw 50 hz , providing and supplying of phase sequence indicator 3 phase 415 v , providing and supplying of frequency meter 45 to 55 hz , providing and supplying of dc led lamp set 3w 5w 10w set of 3 , providing and supplying of dc pump 24 v , providing and supplying of pwm controller , providing and supplying of mppt charge controller , providing and supplying of inverter with battery 1 kva with 12 v battery input 12 volt dc output 220 volt ac

CTN :43363801

14 Jan, 2026 5.32 Lacs

Ranebennur - Karnataka

Tender For corrigendum : construction of nrl mshed in chalageri grama panchayath - cast iron spike gp gud01, mm ms plates gp gud01, mm ms square rodgp gud01, mm 6 mm ms plate gp gud01, corbon electrodes gp gud01, anchor bolts 750mm gp gud01, base plate base plategp gud01, gusset plates 6 mm thick gp gud01, ms angle iron 40mm 40mm 6mm 23 metre in length at kg per metregp gud01, ms angle iron 50mm 50mm 6mm metre in length at kg per metre gp gud01, chlorinated polyvinyl chloride cpvc pipe 25 mm outer dia gp gud01, unit cost as per the specification gp gud01, c i m s brackets for flushing cistern gp gud01, brass stop cock gp gud01, cp brass chain with plug gp gud01, copper plated brass piller tap 15mm gp gud01, white vitreous china clay flat back wash basin size 550 400mm gp gud01, pvc pipes 10kgf sqcm 90mm outer diagp gud01, vitreous china orrisa type w c pan size 580 mm gp gud01, polyenthylene water storage tank of specified capacity lgp gud01, water proofing cement paint gp gud01, enamel paint gp gud01, whitening gp gud01, dry distemper gud01, ceramic tiles 30 30 cms gp gud01, mathi nandi wood scantling for styles ad rails 25 mm thick gp gud01, mathi nandi wood scantling for styles and rails 30 mm thick gp gud01, honnewood planks for panels 20 mm thick gp gud01, honne wood gp gud01, mathinandi wood planks for panels 25 mm thickgp gud01, vitrified tiles 600 600 mm gp gud01, mixer concrete small used in culvert gp gud01, solid concrete blocks 40 20 20 cms5 0 n sqmm gp gud01, jungle wood runners and planksgp gud01, casurina poles 100 - 150 mm gp gud01, silver oak or equivalent planks 38 mm thick gp gud01, binding wire gp gud01, tmt bars fe 500 gp gud01, hom of vibrator 0.71 daysgp gud01, plasticizer super plasticizer gp gud01, mixer concrete 1 cum capacity gp gud01, portland cement gp gud01, coarse sand zonegp gud01, broken stone aggregate 12 mm to 10 mm sizegp gud01

CTN :43486949

19 Jan, 2026 NA

Kupwara - Jammu And Kashmir

Tender For supply of angle iron , cgi sheet , photo frame , flex map , voltas air cooler , flex for screen , water bottle 20 lt , camera fesh , flex banner 8x6 , flex banner 10x7 , matting graphics , therma cool , construction of toilet , plumbibg and labour charges

CTN :43487371

22 Jan, 2026 NA

Nawabganj - Uttar Pradesh

Tender For tender for supply of spring stiffness tester , sfd & bmd apparatus (simple supported and cantilever beam) , youngs modulus (deflection of beam apparatus) , digital vernier caliper 12 inch , torsion testing apparatus , work carpentary bench (fitted with 4 carpentary wise 9 inch) , circular saw grinder , bench grinder , hand drilling machine , wood plainer , band saw blade (brazing unit) , gas cutting unit , barzing equipment with accessories , soldering iron , metal spary gun , pedestal grinder , welding partition screen , work benches with vices (2 numbers) , angle grinder , projection welding machine , portable welding machine (220 amp) , spot welding machine , oxyaccetylene welding set with accessories , electrical welding transformer set with accessories , spray gun 1 lit cup capacity with hose pipe , air compressor with 2hp motor

Angle Iron Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector

State Government