Latest angle iron Tenders | Government angle iron Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

CTN :43502930

19 Jan, 2026 NA

Gandhinagar - Gujarat

Tender For supply of windows handles 150mm left hand , oil putty , peg set 300 mm for ms , ptmtjet spray with 1 mtr tube , pvc ball cock float valve 50mm complete , pvc swr pipe 75mm dia , pvc bath cabinate 350 x 450 mm , pvc bathroom water shower 100mm , pvc connection 15x450mm long complete with nut bolt and washer , pvc connection 15x600mm long complete with nut bolt and washer , pvc cover suitable for all water storage tank 500 ltr complete , pvc flushing cistern 10 ltr cap , pvc grating 100mm , pvc grating 75mm , pvc swr pipe 110mm dia , pvc tee equal 110mm , pvc washer suitable 15mm bore bib tap , pvc waste coupling 40mm , pvc waste pipe corrugated 32 x 900 mm long , ss curtain bracket 25 mm dia , steel screw 25mm x 8g , steel screw wood 45mm x 8g , steel ms hinges butt 75 mm , urinal flat back 450 x 350 x300mm , whb 550x450x440mm , cp overhead shower , pvc water storage tank with lid 1000 ltr , bell joint repair clamp for di pipe 100 mm , gi plug 40mm , gi plug 50mm , di pipe k7 100 mm both end flange , di pipe k7 fitting tee 100 mm both end flange , bell joint repair clamp for ci pipe 100 mm , bell joint repair clamp for ci pipe 150 mm , bell joint repair clamp for ci pipe 200 mm , bell joint repair clamp for di pipe 150 mm , bell joint repair clamp for di pipe 200 mm , gate valve gun metal 50mm , gi socket screwed 50mm , copper sulphate , gate valve gun metal 15mm , eco clean 2300 herbal reagent 1 ltr , gate valve 25mm , gi bend 90 deg 20mm , gate valve gun metal 40mm , cpvc coupler 20mm , cpvc elbows 40mm , cpvc male thraded 20mm , gate valve gun metal 20mm , gi elbow 15 mm , gi socket 15mm , gi union 15mm , bleaching powder , cpvc elbows 20mm , cpvc female thraded 20mm , cpvc female thraded 32mm , cpvc female thraded 40mm , cpvc male thraded 32mm , cpvc male thraded 40mm , cpvc tee 20mm , cpvc tee 40mm , cpvc union 20mm , cpvc union 32mm , cpvc union 40mm , gate valve gun metal 25mm , gi socket 25mm , gi socket 20mm , gi union 20mm , cpvc valve 32 mm , cpvc valve 25 mm , cpvc coupler 32mm , cpvc male thraded 25mm , cpvc reducer socket 32x25mm , round up herbisite 1 ltr , m seal 150 gm , gi union 25mm , liquid defoaming agent , sodium hypoclorite solution , alum ferric solution , calcium hypochlorite , astronomical time switch based on lux level , bell ding dong call bell , cable copper flexible 3 core x2 point 5 sqmm , cable lugs alumn 120 sqmm , cable lugs alumn 150 sqmm , cable lugs alumn 185 sqmm , cable lugs alumn 240 sqmm , cable lugs alumn 25 sqmm , cable lugs alumn 300 sqmm , cable lugs alumn 35 sqmm , cable lugs alumn 50 sqmm , cable lugs alumn 70 sqmm , cable lugs alumn 95 sqmm , cable lugs ring type 100 sqm , cable lugs ring type 120 sqm , cable lugs ring type 150 sqm , cable lugs ring type 240 sqm , cable lugs ring type 25 sqm , cable lugs ring type 300 sqm , cable lugs ring type 35 sqm , cable lugs ring type 40 sqm , cable lugs ring type 50 sqm , cable lugs ring type 70 sqm , cable lugs ring type 95 sqm , cable lugs u type 10 sqmm , cable lugs u type 16 sqmm , capacitor 2 point 5 mfd , engine oil , batton holder , angle holder lamp batten bakelite , ht do fuse 10 amp , ht tape element 11 kv voltage grade insulation , led 9 watt bulb 6500k , led bulb 12 w , led street light 60 w , led street light 70w , led 2x 2 36watt led fitting , ht11 kv cold shrink indoor type cable end joint 95 sqmm , ht11 kv cold shrink outdoor type cable end joint 95 sqmm , ht 11 kv cold shrink straight through joint 95 sqmm , pvc tape roll 40 mm , spn db box 4 way , brass mortice lock four lever //bid details 2 / 125 vertical type , lock 6 lever 100 mm brass , paint se black 1 ltr pack , paint brush 25 mm , paint brush 50 mm , paint brush 75 mm , paint synthetic enamel og in 1 ltr pack , paint white 1 ltr pack , soft broom with grass , tarpentine

CTN :43519536

19 Jan, 2026 NA

Multi City - Multi State

Tender For supply of mild steel angle iron 50x50x6mm , fibre sheet vulcanized 1.2mm thick (4'x8') size , elect rod welding steel mild g/p 3.15mm , bolt bsw s/b u/m hex hd with hex nut 1/4" x 3/4"

CTN :43206566

12 Jan, 2026 NA

Ferozepur - Punjab

Tender For corrigendum : material and labour for construction of 3800 mtr x chain link fence in ferozepur - s&f structural steel post of angle iron 65x65x6mm, 4.50 mtr long, weight as per is 2062-1984 including fabrication of 0.60 mtr both side long top portion swan neck v type at 30 degree to vertical, including making six round holes of 15 mm dia on vertical posts and for fixing of nuts and bolts and three nos of 15 mm dia holes for fixing strut and five nos notches on the swan neck and welding of two nos of 16 mm ms rod each of 0.23 mtr length to bottom end of picket for anchorage including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above gl complete and two coat of bituminous paint embedded portion of angle 0.45mtr. make : jindal/ sail/ tata/equivalent isi marked complete all as specified and directed by engineer-in-charge, s&f structural steel post of angle iron 65x65x6mm, 3.30 mtr long, weight as per is 2065- 1984+b12, including fabrication for strut post bending at top portion, including making three nos holes of 15 mm dia on vertical posts for fixing of nuts and bolts and three nos of 15 mm dia including 0.23 mtr 16 mm dia ms rod two piece to be welded at bottom for anchoring purpose including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above gl complete and two coat of bituminous paint for stud 0.45mtr below gl for one side of the post complete all as specified and directed by engineer-in-charge. make : jindal/ sail/ tata/equivalent isi marked, s&f galvanised two or three strand steel barbed wire (line wire) of 2.24mm diameter of wire, barbs at 75mm spacing. the barbs are (point wire) 02mm thick wire shall be isi marked as per is:278 of 1978 (third revision) with amdt no 1 to 4. the points of barbs shall be sharp. the line and point wires shall be circular in section free from scales and point wires shall be circular in section free from scales and defects and shall be uniformity galvalium. the barbed wire shall be manufactured as per clause 11.2.1 and 11.2.2 respectively of is specification cited above read with is 4826/79 (first revision).make:sail/tata/ aplapollo/rinl/jsw complete all as specified and directed by engineer-in-charge, s&f galvanised steel chain link fence fabric of mesh size 125mm x 125mm (+/-) 4mm of 4.00mm nominal diameter. the size of chain link fence fabric shall be 2.7 mtr x 15 mtr mesh wire. galvalium chain link shall be manufactured as per is 4823 complete all as specified and directed by engineer-in-charge. make : tata/jsw/rinl/ jindal/sail., s&f ms plat of 40x3 mm, 2.70 mtr long with 6 holes of 15 mm dia, including one coat of red oxide primer and two coats of synthetic enamel paint. 3.02 kg per flat. make of steel: jindal/ sail/ tata/equivalent isi marked complete all as specified and directed by engineer-in-charge., s&f mild steel bolts with hexagonal head at one end and screwed the other end fitted with one nut and two washers. the bolts shall be 12mm dia and 50mm long. strong long lasting, resistant to corrosion and 100% recyclable complete all as specified and directed by engineer-in-charge. make: jindal / sail/ tata/ apl apollo/ jsw/ rinl, s&f ms round bars 10mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer. make: jindal/ sail/ tata/ apl appolo/ jsw/ rinl complete all as specified and directed by engineer-in-charge., s&f ms round bars 16mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer make: jindal/sail/tata/apl apollo/jsw/rinl complete all as specified and directed by engineer-in-charge., material and labour for excavating in soft and dense soil trenches, exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m in dept

CTN :43521888

20 Jan, 2026 NA

Multi City - Multi State

Tender For supply of angle iron , cgi sheet , photo frame , flex map , voltas air cooler , flex for screen , water bottle 20 lt , camera fesh , flex banner 8x6 , flex banner 10x7 , matting graphics , therma cool , construction of toilet , plumbibg and labour charges , quarter plate , full plate , badmenton , plt sheet , iron cutter blade

CTN :43363801

14 Jan, 2026 5.32 Lacs

Ranebennur - Karnataka

Tender For corrigendum : construction of nrl mshed in chalageri grama panchayath - cast iron spike gp gud01, mm ms plates gp gud01, mm ms square rodgp gud01, mm 6 mm ms plate gp gud01, corbon electrodes gp gud01, anchor bolts 750mm gp gud01, base plate base plategp gud01, gusset plates 6 mm thick gp gud01, ms angle iron 40mm 40mm 6mm 23 metre in length at kg per metregp gud01, ms angle iron 50mm 50mm 6mm metre in length at kg per metre gp gud01, chlorinated polyvinyl chloride cpvc pipe 25 mm outer dia gp gud01, unit cost as per the specification gp gud01, c i m s brackets for flushing cistern gp gud01, brass stop cock gp gud01, cp brass chain with plug gp gud01, copper plated brass piller tap 15mm gp gud01, white vitreous china clay flat back wash basin size 550 400mm gp gud01, pvc pipes 10kgf sqcm 90mm outer diagp gud01, vitreous china orrisa type w c pan size 580 mm gp gud01, polyenthylene water storage tank of specified capacity lgp gud01, water proofing cement paint gp gud01, enamel paint gp gud01, whitening gp gud01, dry distemper gud01, ceramic tiles 30 30 cms gp gud01, mathi nandi wood scantling for styles ad rails 25 mm thick gp gud01, mathi nandi wood scantling for styles and rails 30 mm thick gp gud01, honnewood planks for panels 20 mm thick gp gud01, honne wood gp gud01, mathinandi wood planks for panels 25 mm thickgp gud01, vitrified tiles 600 600 mm gp gud01, mixer concrete small used in culvert gp gud01, solid concrete blocks 40 20 20 cms5 0 n sqmm gp gud01, jungle wood runners and planksgp gud01, casurina poles 100 - 150 mm gp gud01, silver oak or equivalent planks 38 mm thick gp gud01, binding wire gp gud01, tmt bars fe 500 gp gud01, hom of vibrator 0.71 daysgp gud01, plasticizer super plasticizer gp gud01, mixer concrete 1 cum capacity gp gud01, portland cement gp gud01, coarse sand zonegp gud01, broken stone aggregate 12 mm to 10 mm sizegp gud01

CTN :43486949

19 Jan, 2026 NA

Kupwara - Jammu And Kashmir

Tender For supply of angle iron , cgi sheet , photo frame , flex map , voltas air cooler , flex for screen , water bottle 20 lt , camera fesh , flex banner 8x6 , flex banner 10x7 , matting graphics , therma cool , construction of toilet , plumbibg and labour charges

CTN :43487227

19 Jan, 2026 18.0 Thousand

Tinsukia - Assam

Tender For supply of angle iron , bar rod , black tape , m seal , quick fick

CTN :43487718

17 Jan, 2026 NA

Tinsukia - Assam

Tender For supply of thinner , dentrite , puttey , paint red oxide , elect rodes welding , leather cloth black , steel angles , iron sheet , wire electric copper , first aid kit , beeding

CTN :43180507

09 Jan, 2026 NA

Bathinda - Punjab

Tender For bid to ras tender for supply of mobile solar set 5 kva : :--72 cell ware solar panel 550 watt with power tolerance of 0pt5w maximum system voltage of 1500 and voltage at maximum power at 36pt70vmp the solar panel is made up of poly crystalline silicon with 72 solar cell per module that would be of 1 pt 5 mtr x 2 pt 00 mtr encapsulated with ethylene vinyl acetate make luminous waree utl , solar inverter 5 kva 120v with power conditioning unit integrate that consist of grid charger inverter and mppt solar charger the 5kva 120v solar inverter used solar and grid to charge the batteries since the usage of power from the grid is secondary grid power is only used when solar energy is not present make utl luminous , lead acid tubular batteries with the capacity of 150ah with normal voltage of 12v per battery make exide amaron utl luminous , 2 core 6 sqmm wire required to give connection from solar panels to batteries and for the electrical fitting purpose make havells anchor bajaj , rack for batteries ms iron angle frame size of 65cm x 65cm x 210cm , change over 100 amp make havells anchor bajaj , mcb 63 amp make havells anchor bajaj , trolley mobile solar set will be fixed on heavy duty steel trolley with 2 lockable wheels tyre should be size of 7 pt 50 to 16 14 ply rating and load capacity of 2 pt 50 ton trolley to have parking and over run break pulley tow hook and leaf spring four set 1 nos axles super structure of the trolley should be made of 150m x 75mm x 5mm thick u channel angle iron of size 75mm x 75mm and top platform 4mm thick ms plate necessary arrangement for fixing of 5 kva solar system with 01 nos tool box lockable battery compartment solar panel fold dimensions folded size 4 mtr l x 2 pt 10 mtr w x 0 pt 75 mtr h unfolded size 6 mtr l x 4 pt 5 mtr w mobility features four wheels with specify type pneumatic solid easy to tow or transport deployment process manual unfolding of solar panels instant electricity output from sunlight

Angle Iron Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government