Latest bolt machine Tenders | Government bolt machine Tenders

Central Government/Public Sector

CTN :45713879

20 Jul, 2026 NA

Jorhat - Assam

Tender For repairs to compound wall, fencing and gate with connected items in domestic area and omq area at afs under ge (af) jorhat - demolition of brick work built in cement mortar of any description complete all as specified and as directed., m&l for brickwork (old size) with sub class b bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar (1:6) complete all as specified and as directed., all as per serial item no. 2 here-in-before but except bricks, using old serviceable brick as retrieved from demolition.note : old serviceable bricks obtained from serial item no. 1 above shall re-used., taking down cement plaster on brick or stone or concrete surfaces of walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed., m&l for rendering 15mm thick on fair face of brick works or concrete surfaces of walls with cm (1:4), finishing the surface even and smooth without using extra cement complete all as specified and as directed., m&l for preparation of new plastered surfaces of walls and applying two coats of cement base paint over and including one coat of alkali resistance primer complete all as specified and as directed., demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed., m&l for plain cement concrete (1:2:4) type b-0 (using 12.50mm graded stone aggregate) used as in benching and coping including necessary formwork complete all as specified and as directed., m&l for brickwork with sub class b bricks, straight or curved on plan to any radius in half brick thick walls, built in cm (1:4) complete all as specified and as directed., m&l for dismantling posts or struts (wood, steel or rcc) any section, including taking out embedded portion and making good to disturbed ground surfaces complete all as specified and as directed., m&l for plain cement concrete (1:3:6) type c-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, etc. complete all as specified and directed., s&f hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing, etc. wind ties for roof including securing bolts posts and struts in fencing of size 65x65x6mm including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to fe-290 gde e-165 complete all as specified and as directed., dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed., s&f 11mm to 15mm dia of shank mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and onehexagonal or square nut, but length of bolt exc. 5cm but n. exc. 10cm complete all as specified and as directed., excavating in post holes (or similar holes) each n. exc. 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc. 50m and making good surface as in soft/loose soil complete all as specified and as directed., m&l for preparation of new steel and iron surfaces of any description over 10cm width or girth not otherwise described for and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and as directed., m&l for mild steel tmt bar 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends binding wit

Central Government/Public Sector

CTN :45725084

09 Jul, 2026 NA

Angul - Odisha

Tender For providing of custom bid for services - service pr for erection commissioning part of rm of burner tilt system of unit 2 of tstps stage-1

Central Government And Public Sector

CTN :45730196

16 Jul, 2026 NA

Bhilai - Chhattisgarh

Tender For supply of lock bolting machine with power pack and tool size- 1/2, 3/4, 5/8" & 7/8" for manufacturing of new wagon with all concomitant accessories as per annexure-a & b. make: stanley, huck, avlock, hitesh udyog or similar. [ warranty period: 30 months after the date of delivery ] ]

CTN :45733162

01 Jul, 2026 NA

Jamalpur - Bihar

Tender For supply spare parts of power pack assembly of huck bolting machine compatible with power pack unit of orione make huck- bolting machine model no.-ohpl-p540, as per attached annexure, qty.- 01 set. (one set consist of sl. no. 01 to 14, total nos. of items-64 nos.) [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45717821

22 Jul, 2026 NA

Katni - Madhya Pradesh

Tender For supply of huck bolt machine as per attached annexure - a [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45469479

08 Jul, 2026 NA

Bhavnagar - Gujarat

Tender For corrigendum : tender for supply of system description general requirements including cyber security technical requirements full hd fixed box type ip colour camera with varifocal lens and housing & mount 4k uhd fixed box type ip colour camera (type a/type b) with varifocal lens and housing & mount full hd bullet type ip colour camera 4k uhd bullet type ip colour camera (type a/type b) full hd fixed dome type ip colour camera full hd ptz (pan, tilt, zoom) ip colour camera digital keyboard large format display monitor server/workstation hardware network video recorder (nvr) pc workstation external storage device core switch (1). aggregation switch (ii). layer 2 switch (24 port) a. poe b. non-poe (iii) field switch a. b port b. 4 port wireless transmitter/receiver unit copper to fiber media convertor various types of cables software requirement video management software graphical user interface client software video recording software artificial intelligence (al) enabled video analytics software remote viewing on web and mobile app functional requirement of command control centre (ccc) software face recognition software software license test requirements test procedure quality assurance making and packing information to be supplied by the purchaser training documentation schematic diagram- 1: schematic diagram of ip based video surveillance system at stations schematic diagram 2: schematic diagram for video surveillance system for cluster of stations schematic diagram- 3: schematic diagram for cloud based architecture of video surveillance system for cluster of stations

State Government

CTN :45684098

24 Jul, 2026 4.72 Crore

Belgaum - Karnataka

Tender For tender for establishment of centre of excellence in electrical vehicle at vtu regional centres of muddenahalli, mysuru, kalaburgi and talakal - servo motor rotating arm, propeller fin, battery connector, jumper pin header, battery holder, cable usb, button cap large passive elements, button small passive elements, button large passive elements, potentiometer(10ko) passive elements, switch passive elements, capacitor(10uf) passive elements, capacitor(104) passive elements, resistor(10ko) passive elements, resistor(1ko) passive elements, resistor(220o) passive elements, big blue led active elements, big yellow led active elements, big green led active elements, big red led active elements, rgb led active elements, diode active elements 1n4001, diode active elements 1n4148, pnp transistor 8550 active elements, npn transistor(8050) active elements, relay active elements, active buzzer active elements, motor drivers, seven segment display, lcd display, dc motor, servo motor, m to m jumper wires, f to f jumper wires, m to f jumper wires, tilt sensor, ultrasonic sensor holder, light sensor, ultrasonic proximity sensors, analog temparature sensors, breadboards, uno board, tx/rx module, usb cable for stm32 board, stm32 discovery board, basic can bus protocol training system, elecetrical vehicle charging technology bench, multi mcu trainer kit (with banana plug-ins), power electronics pre-build kit, permanent magnet synchronous motor with regen, differential gear training model (ev auto), ev wiring and harness system mock layout (2-wheeler), four wheeler simulator pmsm / bldc motor kit, battery management system (bms) training module, belt pulley, female type 6 charging socket, front wheel axle, front wheel rim ( 12 inch), tubeless tyres, main stand, side stand, mid - drive chassis, switches ignition, horn, indicator, head light, cone-set, handle bar, t-stamp, fork, smart charger can, dc-dc converter, swing arm, vcu, brake sensors, display, wiring harness, throttle (re twistable), mid drive motor 3kw and pull belt, mcu 120a, battery 4kw nmc, cordless drill machine tools, tool kit trolley tools, pipe wrench tools, screwdriver 803 tools, taparia screw driver 863 200 tools, taparia philips s/d psc862250 tools, taparia screw driver 861 100 tools, installation tape tools, soldering gun tools, multimeter tools, hammer - 40mm nylon tools, hammer - 500g tools, chissel tools, socket set box 24pc tools, long circlip plier outer tools, long circlip plier inner tools, t spanner 14mm tools, t spanner 12mm tools, t spanner 10mm tools, t spanner 8mm tools, t spanner 7mm tools, connector - 902 tools, tester tools, nose plier tools, monkey plier tools, wise grip plier tools, cutting plier tools, wire cutter tools, screw driver 2 in 1 - 903ibt tools, ring spanner set tools, double end spanner set tools, t allen key 3,4,5,6 mm tools, l allen key set tools, regulated power supply, motor hall phase tester, continuity tester, helmet, clamp meter, taco meter, hall sensor, shaft drive motor, bldc motor (cut section), pmsm motor (cut section), four wheelar car, shaft drive 2w full vehicle naked, mid drive 2w full vehicle 1, hub drive 2w full vehicle 1, hub drive 2w full vehicle naked 1, mid drive 2w full vehicle, mid drive 2w full vehicle naked, hub drive 2w full vehicle, hub drive 2w full vehicle naked, lfp cells 3.2 v 100 ah, hot air blower, screw gauge, black 12 awg wire, red 12 awg wire, hly cells, chogori 4+2 female connector, chogori 4+2 male connector, crimper, iec female connector, iec male connector, anderson sb50, safety gloves, safety glasses, duct tape 55mm, filament tape 55mm, kapton tape 55mm, lead, cell holder 2x2 - 32650, cell holder 2x2 - 21700, cell holder 2x2 - 18650, nickel strip - 32650, nickel strip - 21700, nickel strip - 18650, lfp cells 3.2 v 6 ah - 32650, nmc cells 3.7 v 4 ah - 21700, nmc cells 3.7 v 2.5 ah - 18650, spot welding machine 1kva (pneumatic), active balancer 24s 10 amps, ir tester

State Government

CTN :45695199

10 Jul, 2026 4.99 Crore

Belgaum - Karnataka

Tender For tender for establishment of centre of excellence in electrical vehicle power train technologies at vtu regional centre, bengaluru - servo motor rotating arm e, propeller fin e, battery connector e, jumper pin header e, battery holder e, usb cable e, button cap (large)passive elements, button(small) passive elements, button(large)passive elements, potentiometer(10ko)passive elements, switchpassive elements, capacitor(10uf)passive elements, capacitor(104)passive elements, resistor(10ko)passive elements, resistor(1ko)passive elements, resistor(220o)passive elements, big blue led active elements e, big yellow led active elements e, big green led active elements e, big red led active elements e, rgb led active elements e, active elements 1n4001 diode, active elements 1n4148 diode, pnp transistor(8550) active elements, npn transistor(8050) active elements e, relay active elements e, active buzzer active elements ev, motor driver e, seven segment display e, lcd display e, dc motor e, servo motor e, jumper wires e, tx/rx module e, tilt sensor e, ultrasonic sensor holder e, light sensor e, ultrasonic proximity sensors e, analog temparature sensors e, breadboards e, uno board e, usb cable for stm32 board e, ecu board, stm32 discovery board e, battery cell making machine, integrated electronics workstation, pcb design equipment, dynamometer 2w, electrical vehicle motors and drives workbench, battery management system (bms) training module e, model-based development (mbd) real-time controller, power electronics training bench, off board charger control board, pe-pp control panels, pdi unit, dc converters, drive axles, wheel axles, foot throttle e, auxiliary battery, relay e, harness, wheels e, differential e, moter ev, bms e, vcu e, mcu e, on board charger, battery pack e, naked chassis, belt pulley e, female type 6 charging socket e, front wheel axle ev, front wheel rim ( 12 inch) e, tubeless tyres e, main stand ev, side stand ev, mid - drive chassis e, switches ignition, horn, indicator, head light ev, cone-set ev, handle bar ev, t-stamp ev, fork ev, smart charger can ev, dc dc converter ev, swing arm ev, vcu ev, brake sensors ev, display ev, wiring harness ev, throttle (re twistable) ev, mid drive motor 3kw and pull belt e, mcu 120a e, battery 4kw nmc ev, cordless drill machine tools ev, tool kit trolley tools e, pipe wrench tools e, screwdriver 803 tools e, taparia screw driver 863 200 tools ev, taparia philips s/d psc862250 tools ev, taparia screw driver 861 100 tools e, installation tape tools ev, soldering gun tools e, multimeter tools e, hammer - 40mm nylon tools ev, hammer - 500g tools ev, chissel tools ev, tools 24pc socket set box, long circlip plier outer tools ev, long circlip plier inner tools ev, t spanner 14mm tools ev, t spanner 12mm tools ev, t spanner 10mm tools e, t spanner 8mm tools ev, t spanner 7mm tools ev, connector - 902 tools ev, tester tools ev, nose plier tools ev, monkey plier tools e, wise grip plier tools e, cutting plier tools e, wire cutter tools e, screw driver 2 in 1 - 903ibt tools ev, ring spanner set tools ev, double end spanner set tools ev, t allen key 3,4,5,6 mm tools ev, l allen key set tools ev, motor hall phase tester ev, continuity tester ev, safety helmet, programmable mcu, clamp meter ev, taco meter ev, mid drive mcu, hub motor mcu, hall sensor ev, mid drive stator, hub drive stator, induction stator, bldc stator, mid drive rotor, hub drive rotor, induction rotor, bldc rotor, induction motor, brush motor, shaft drive motor ev, bldc motor, pmsm motor, ev 4w - car, ev 3w - auto ev, ev2w - shaft drive - full vehicle, ev 2w - hub drive full vehicle ev, ev 2w - mid drive - full vehicle ev, ev 2w - hub drive - full vehicle ev, ev 2w - mid drive - full vehicle, ev 2w - hub drive - full vehicle, eight channel 3 amps cdc cell grading machine, cells bolt, cell 3.2 v 100ah lfp, hot air blower ev, green 100mm insulation, clamp meter 0-600 amps, battery tester, bus bars, screw gauge ev, silicon black, bla

State Government

CTN :45685523

08 Jul, 2026 44.62 Lacs

Bharuch - Gujarat

Tender For providing and supplying furniture for iti valia, dist.bharuch - providing and supplying high-back chair with a durable metal framework, upholstered with artificial leather/leatherette and molded pu foam. the chair shall include molded seat and back covers, with the back foam ergonomically contoured to provide lumbar support for enhanced comfort. the chair shall be equipped with high-durability casters and a hydraulic system. it must feature a gas lift cylinder with a minimum 5-year warranty. the overall dimensions of the chair shall be approximately 53 cm (w) x 79 cm (h) for the back, and 51 cm (w) x 49 cm (d) for the seat. the pu foam shall be molded with a density of 45 ± 2 kg/m³. the chair shall have one-piece armrests that are scratch and weather resistant. it shall be equipped with a permanent contact mechanism allowing 360° rotation, 12° seat tilt, and 19° back tilt with a front pivot for tilting, ensuring the user's feet remain on the ground for added comfort. additional features shall include tilt tension adjustment, static seat depth adjustment of 0.5 cm, 5-position locking system, and an anti-shock back mechanism to prevent sudden impact when the backrest lock is released. it shall be confirmed and approved in advance by the architect, along with a description and image, or as directed by the engineer-in-charge. , providing and supplying medium-back chair with a durable metal framework, upholstered with changeable fabric upholstery covers (as per requirement) and molded pu foam. the chair shall include molded seat and back covers, with the back foam contoured to provide lumbar support for added comfort. it shall have high-durability casters and a hydraulic system with a gas lift cylinder having a minimum 5-year warranty. chair dimensions shall be approximately 47.5 cm (w) x 58 cm (h) for the back, and 49 cm (w) x 48 cm (d) for the seat. the pu foam shall be molded with a density of 45 ± 2 kg/m³. the chair shall include one-piece armrests that are scratch and weather resistant. it shall be equipped with a permanent contact mechanism offering 360° rotation, pneumatic height adjustment, 17° maximum tilt, and tilt tension adjustment. it shall be confirmed and approved in advance by the architect, along with a description and image, or as directed by the engineer-in-charge. , providing and supplying law back chair for work center & other staff the seat & back are made of m.s frame work. upholstered with changeable fabric upholstery covers (as per requirement) and molded pu foam, together with molded seat & back covers. the back foam should be designed with contoured lumber support for extra comfort. caster of high durability & hydraulic. the chair should have cylinder with 5 years warranty. the size of chair 45cm x 45cm (back side) and 45cm x 43cm (seat size). the pu foam should be molded with density =45 ± 2 kg/m3 .with one piece armrests. the armrests are scratch and weather resistant. the permanent contact mechanisms is designed with 360° revolving type, with pneumatic height adjustment & 17° maximum tilt only & tilt tension adjustment facility. complete as per sample approved and as directed by the architect and approved by the engineer in charge , providing and supplying visitor or guest chair with seat and back made of 12 mm thick hot-pressed plywood, upholstered with changeable fabric upholstery covers (as per requirement) and molded pu foam, along with molded seat and back covers. the back foam shall be contoured to provide lumbar support for enhanced comfort. the chair dimensions shall be approximately 45 cm (w) x 38 cm (h) for the back, and 45 cm (w) x 43 cm (d) for the seat. the pu foam shall be molded with a density of 45 ± 2 kg/m³. the armrests and legs shall be fabricated from powder-coated mild steel (ms) structure as per architect's selection. the seat and back shall be securely fixed to the ms structure using all necessary hardware. it shall be confirmed and approved in advance by

State Government

CTN :45696031

02 Jul, 2026 NA

Palwal - Haryana

Tender For supply of furniture for the office of svsu skill innovators foundation - description for the furniture for the office of ssif, svsu., executive director table with side storage unit. size: approx. 2400 mm (l) 900 mm (w) 750 mm (h). made from premium quality engineered wood/action tesa/merino laminated board/pre-laminated particle board of minimum 25 mm top thickness and 18 mm side panels. matte finish laminate with pvc edge banding (2 mm thick). color combination: tan or brown. integrated side credenza with lockable drawers, open shelves, cpu space, keyboard tray, wire manager, cable routing grommets, modesty panel, and storage cabinet. high-quality hardware and accessories from reputed brands such as ozone, hettich, hafele, godrej, door set, century, or equivalent. corrosion-resistant fittings and telescopic channels. scratch-resistant, termite-resistant and moisture-resistant surface finish. environment-friendly manufacturing process using low voc materials. five-stage quality inspection before delivery and installation., boss chair (high back executive chair)premium executive high-back ergonomic revolving chair with adjustable headrest and lumbar support. upholstered in high-quality leatherette/pu upholstery. heavy-duty chrome/nylon base with 360 swivel mechanism. class-4 gas lift for height adjustment. multi-lock synchro tilt mechanism with tension control. padded armrests. seat and back made from molded high-density pu foam for superior comfort. load-bearing capacity minimum 120 kg. suitable for long working hours. color: brown. warranty: minimum 1 year., visitor chair (mid back): seat and back frame made from commercial-grade plywood with molded high-density foam cushioning. upholstery in premium leatherette fabric. heavy-duty powder-coated/chrome-finished metal frame. color: tan/brown. ergonomic mid-back design for visitor comfort. dimensions: seat width 19 inches, seat depth 19 inches, seat height 20.5 inches, back height 19 inches. weight capacity: up to 100 kg minimum. anti-rust frame finish with floor-protective nylon bushes., sofa set (5 seater): premium 5-seater sofa set consisting of one 3-seater and two single-seater sofas or equivalent configuration. solid hardwood/seasoned wooden frame structure. high-density resilient foam cushioning with premium leatherette upholstery. comfortable back support and armrests. scratch-resistant and easy-to-clean finish. color: brown/tan/beige as approved by purchaser. heavy-duty construction suitable for office reception and executive lounge areas, t.v (43 inch / 40 inch) 43-inch (or 40-inch) full hd/4k smart qled television with google tv/android tv operating system. minimum resolution: 1920 1080 (full hd) or higher. built-in wi-fi, bluetooth connectivity, screen mirroring, chromecast support, voice-enabled remote control. hdmi (minimum 2 ports), usb (minimum 2 ports), ethernet port. wall mounting kit and installation included. reputed brands., coffee table: - premium center/coffee table made from 36 mm thick plywood/engineered wood structure with matte laminate finish. square shape. approximate size: 900 mm 900 mm 450 mm height. smooth edges with pvc edge banding. sturdy load-bearing design suitable for executive office and lounge areas. scratch-resistant and easy-maintenance finish. color matching with sofa set and office interiors., office partition: - decorative office partition with overall size approximately 144 cm (w) 182 cm (h). three-panel folding design. strong engineered wood/solid wood frame with cnc-cut decorative art deco/jaali pattern. color: white and brown. easy folding and relocation facility. stable base support with anti-slip feet. suitable for creating executive office privacy zones and waiting area segregation. premium finish with smooth edges and durable construction., file cabinet vertical storage cabinet made from premium quality engineered wood with matte laminate finish. color: off white wood grain. dimensions: w 30" d 14" h 72". multiple storage com

Bolt Machine Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors