Get complete information related to latest Check Nut Scrap Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Check Nut Scrap Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Check Nut Scrap Tenders.
Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.
Tender For supply of 10004801aa primary filter element , 10004802aa secondary filter element , st001 side cutter lh , st002 side cutter rh , 10002575aa fuel filter , 10027339ab hyd filter , 10004836ab engine oil filter , mt001 middle tooth , tb022 bolt and nut teeth , lb001 side cutter bolt and nut , lb002 side cutter nut and bolt , sb106 bush , sb102a bush , sc3050 hyd tank suction stainer , sb216 hard bush , sb215 hard bush , sb209 hard bush , sb203 split bush , sb208 split bush , bd212ch pin bp 260 , 212ch pin bp211 , lb001 cross bolt , lb002 cross bolt , b1613210 locking bush , sb210 hard bush , 214 kpt kpl pin bp , bp204 pin , csk003 seal kit
Tender For bid to ras replacement of door hinges(qty 02 for each db) , replacement of lm (ebonite) sheet (size lb- 30 cm x 30 cm) , replacement of indication lamp(qty 03 for each db) , replacement of push button (qty - 02 for each db) , replacement of mcbs (mcns provide by ss 14 qty mcbs for each db) , replacement of internal cabling (2x1. 5 sqmm length per db 1. 5 mtr) , internal cleaning of db ( size ldb- 40cm x 37cm x 19. 5cm) , painting of db ( size ldb- 40cm x 37cm x 19. 5cm) , replacement of locking nut ( qty - 02 for each db)
Tender For supply of chasis dynamometer d d -air compressor , spark plug cleaning machine , screw driver set , ring spanner set , open end spanner set , socket goti spanner set , pliers , monkey pliers , outer and inner pliers , tool box , tee spanner , allen key set , tappet puller , tappet gauge , digital multimeter , tachometer , hammer set , tyre pressure gauge , oil measurement can , oil cane mannual pump , tool trolley , magnetic coil , drain pain , hydraulic jack , bench vice , pneumatic rivet nut gun , oil pressure gauge , allen watch , chain watch , locking watch , carbon scraper , gasket , scraper 01 set , vernier caliper digital , micrometer , flow meter , temperature gauge , dial gauge , hand tools , power tools , lifting jack tools , brake roller tester , chassis dynamometer , portable car washer , tools , gloves , safety shoes , fire extinguisher , safety glasses , head protection , safety rescue hook , insulated rubber mat , warning sign stickers , post and chain , face mask , two wheeler ev trainer kit , two wheeler work bench , dc fast charger , hand fire extinguisher , air racket , stud remover , stud remover with socket , tap and dive , torque wrench , tubeless tyre repair kit , threat wear indicator , 4 point relay , 5 point relay , three wheeler , old second hand lead acid battery , bms tester , bldc motor , soldering iron kit , ev charging system , power steering , suspension kit , battery load tester , battery charger , hub motor kit , disck brake assembly , battery cell lithium ion , powertrain with differential ) /bid number: gem/2026/b/7072277 * /dated: 07-01-2026 & & / bid document1 / 57
Tender For supply of sprocket part no. saipfb20003 , centering ring female part no. saipfb20022 , centering ring male part no. saipfb20021 , bearing housing ds with bearing part no. saipfb20031 , bearing housing nd with bearing part no. saipfb20030 , bit holder part no. saipfb20025 , cutting bit part no. saipfb20026 , joining link flat type 34 x 126 part no. saipfb20037 , locking ring part no. saipfb20027 , scraper bar part no. saipfb20033 , slf locking nut part no. saipfb20035 , special locking bolt part no. saipfb20034 , driving plate assembly part no. saipfb20049 , flexible disc part no. saipfb20050 , sprocket part no. saipfb20014 , tensioning bolt part no. saipfb20017 , hd magniflex ring part no. saipfb20042