Latest check nut scrap Tenders | Government check nut scrap Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government/Public Sector

CTN :43378896

14 Jan, 2026 NA

Guna - Madhya Pradesh

Tender For corrigendum : tender for supply of bearing -cylindrical roller bearing , single row , bearing designation/number-skf nu311 ecj or equivalent , cage material- steel , make- fag/skf/ntn , single row angular contact ball bearing no.7311 bdb c3 or 7311 b-jp-ua or skf 7311 bmp or equivalent (steel/brass cage) , make- skf/ntn/fag , cylindrical roller bearing , single row. bearing designation / number- skf nu207 e/ fag nu207e.tvp2 / ntn nu207e or equivalent make- skf /fag / ntn. cage material- steel , cylindrical roller bearing , nu211 b or equivalent , cage material- steel/brass , make- skf / fag / ntn only , angular contact ball bearing. single row. bearing designation / number , fag 7309 b.tvp.ua / skf 7309 bpg /ntn 7309 b.t2.d2 , make- fag / skf /ntn only , self aligning ball bearing , double row , bearing designation / number- skf 2310 m / ntn 2310 s , or equivalent cage material- steel , make- skf / ntn /fag , cylindrical roller bearing , single row , bearing designation / number- skf nu307.c3 ecp or equivalent , cage material- steel , make ntn/fag/skf only , angular contact ball bearing no. skf 7307bec / fag 7307 b.tvp / ntn 7307c , or equivalent , (steel/brass cage) , make- skf / fag / ntn only , angular contact ball bearing , single row , bearing designation /number- skf 7206 b or equivalent , cage material- ss , make- ntn. , angular contact ball bearing , single row , bearing designation / number- skf 7308becb / fag 7308b.tvp.ua /ntn 7308bdb c3 or equivalent , make- skf / fag / ntn , spherical roller bearing , double row , bearing designation / number- fag 22216 e1.c3 / skf 22216 e.c3/ ntn 22216 b.d1.c3 , make- ntn/skf/fag only , deep groove ball bearing , single row , bearing designation / number- fag 6213 c3 / skf 6213 c3 / ntn 6213 c3 , make- fag / skf / ntn , deep groove ball bearing with pressed steel cage , bearing designation/ number- 6212. c3 of fag , skf or ntn make only , cylindrical roller bearing , single row , bearing designation / number- skf nu308 / fag nu308 / ntn nu308 or equivalent , make- skf /fag / ntn with steel cage. , spherical roller bearing with taper bore , double row , bearing designation/number- skf 22211ek /fag 22211e1k / ntn 22211ek , cage material- steel , make- skf/fag/ntn only , spherical roller bearing with taper bore , double row , bearing designation/number- skf 22209ek /fag 22209e1k / ntn 2209ek , cage material- steel , make- skf/fag/ntn only , adapter sleeve , designation- h-311 suitable for bearing 22211k adapter sleeve (taper sleeve along with lock nut & lock washers) , make- skf /fag/ntn only , adapter sleeve (taper sleeve along with lock nut & 2 lock washers) , designation- h-316 , suitable for bearing 22216k , make- skf/fag/ ntn only , adapter sleeve , designation- h 309 , suitable for bearing 22209k adapter sleeve (taper sleeve along with lock nut & 2 lock washers) , make- skf/fag/ntn only , spherical roller bearing , double row metallic cage , with circular groove & lubricating holes on the outer ring bearing designation/number skf22322 e c3 , fag22322 e1 c3 , ntn22322 bd1 c3 or equivalent , make- skf/ fag/ntn only , single row full complement cylindrical roller bearing , bearing designation/number- skf ncf 3052 cv c3 or fag sl183052 c3 or equivalent , make- skf/fag/ ntn , single row full complement cylindrical roller bearing , bearing designation/number- skf njg 2330 vh c3 or fag sl192330 tb c3 or ntn equivalent , make- skf/fag/ ntn. , single row angular contact ball bearing no.7310 bdb or 7310 b-jp-ua or skf 7310 bmp or equivalent , (steel/brass cage) , make- skf/ntn/fag , tapered roller bearing. bearing designation /number- skf 31310j2/df03 or fag 31310a.k11.a60.100 or equivalent , make- skf/fag/ntn. 1 set of bearings consists of 2 nos. of bearing no.31310a.n11 formerly k11 and 1 nos. of spacer no. a60.100 , for total axial float in assembled condition to be between 60- 100 microns bearing must be purchased as a set only. cage material- steel required for 31-p-

Central Government/Public Sector

CTN :43519774

19 Jan, 2026 NA

Multi City - Multi State

Tender For supply of m36 x 140mm carbon steel bolt- moc sa 193 gr. b7 , m36 carbon steel nut -moc sa 194 gr. 2h

State Government

CTN :43236713

16 Jan, 2026 NA

Jharsuguda - Odisha

Tender For corrigendum : supply of mgr rail items : : -0 60 kg grs pad for 1 in 8. 5 p and c, rt-4965 , 60 kg grs pad for 1 in 12 p and c, rt-4218 , steel channel sleeper fittings, ba1636 1 r2 , nut for 28mm dia hookbolt galvanizing , tappered split pin 5mmx75 mm of28 mmbol , cms crossing for1in 8. 5 p and c, rt4967,60kg , switch for1 in 8. 5 p and c,60 kg rail rt4966 , switch for 1 in 12 p and c,60 kg rail rt4219

CTN :43206566

12 Jan, 2026 NA

Ferozepur - Punjab

Tender For corrigendum : material and labour for construction of 3800 mtr x chain link fence in ferozepur - s&f structural steel post of angle iron 65x65x6mm, 4.50 mtr long, weight as per is 2062-1984 including fabrication of 0.60 mtr both side long top portion swan neck v type at 30 degree to vertical, including making six round holes of 15 mm dia on vertical posts and for fixing of nuts and bolts and three nos of 15 mm dia holes for fixing strut and five nos notches on the swan neck and welding of two nos of 16 mm ms rod each of 0.23 mtr length to bottom end of picket for anchorage including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above gl complete and two coat of bituminous paint embedded portion of angle 0.45mtr. make : jindal/ sail/ tata/equivalent isi marked complete all as specified and directed by engineer-in-charge, s&f structural steel post of angle iron 65x65x6mm, 3.30 mtr long, weight as per is 2065- 1984+b12, including fabrication for strut post bending at top portion, including making three nos holes of 15 mm dia on vertical posts for fixing of nuts and bolts and three nos of 15 mm dia including 0.23 mtr 16 mm dia ms rod two piece to be welded at bottom for anchoring purpose including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above gl complete and two coat of bituminous paint for stud 0.45mtr below gl for one side of the post complete all as specified and directed by engineer-in-charge. make : jindal/ sail/ tata/equivalent isi marked, s&f galvanised two or three strand steel barbed wire (line wire) of 2.24mm diameter of wire, barbs at 75mm spacing. the barbs are (point wire) 02mm thick wire shall be isi marked as per is:278 of 1978 (third revision) with amdt no 1 to 4. the points of barbs shall be sharp. the line and point wires shall be circular in section free from scales and point wires shall be circular in section free from scales and defects and shall be uniformity galvalium. the barbed wire shall be manufactured as per clause 11.2.1 and 11.2.2 respectively of is specification cited above read with is 4826/79 (first revision).make:sail/tata/ aplapollo/rinl/jsw complete all as specified and directed by engineer-in-charge, s&f galvanised steel chain link fence fabric of mesh size 125mm x 125mm (+/-) 4mm of 4.00mm nominal diameter. the size of chain link fence fabric shall be 2.7 mtr x 15 mtr mesh wire. galvalium chain link shall be manufactured as per is 4823 complete all as specified and directed by engineer-in-charge. make : tata/jsw/rinl/ jindal/sail., s&f ms plat of 40x3 mm, 2.70 mtr long with 6 holes of 15 mm dia, including one coat of red oxide primer and two coats of synthetic enamel paint. 3.02 kg per flat. make of steel: jindal/ sail/ tata/equivalent isi marked complete all as specified and directed by engineer-in-charge., s&f mild steel bolts with hexagonal head at one end and screwed the other end fitted with one nut and two washers. the bolts shall be 12mm dia and 50mm long. strong long lasting, resistant to corrosion and 100% recyclable complete all as specified and directed by engineer-in-charge. make: jindal / sail/ tata/ apl apollo/ jsw/ rinl, s&f ms round bars 10mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer. make: jindal/ sail/ tata/ apl appolo/ jsw/ rinl complete all as specified and directed by engineer-in-charge., s&f ms round bars 16mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer make: jindal/sail/tata/apl apollo/jsw/rinl complete all as specified and directed by engineer-in-charge., material and labour for excavating in soft and dense soil trenches, exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m in dept

CTN :43502582

19 Jan, 2026 NA

Delhi - Delhi

Tender For supply of 19mm waterproof board 8x4mm , gipsum screw black 2 inches alloy steel coarse thread and corrision resistant , gipsum screw spring washer galvanized zinc plated and corrision resistant , nut bolts 50mmx6mm alloy steel aps , 1 inches margin of 5 feet length waterproof , nail 17 swg mild steel woodworking , fevicol strong bonding wood and heatex resistant , paint red surface suitable burger , paint black surface suitable burger , paint white surface suitable burger , copper wire 1 core 1 point 5 sqmm polycab pvc , copper wire 2 core 1 point 5 sqmm polycab pvc , extension board anchor 1 point 5 meter long with 4x16amp socket , hammer drill bit 12mm heavy duty , hammer drill bit 10mm heavy duty , capasitor 1 point 75 mfd indtech , capasitor 2 point 5 mfd indtech , capasitor 2 mfd indtech , insulation tape 30 meter longsteel grip pvc elect

CTN :43519536

19 Jan, 2026 NA

Multi City - Multi State

Tender For supply of mild steel angle iron 50x50x6mm , fibre sheet vulcanized 1.2mm thick (4'x8') size , elect rod welding steel mild g/p 3.15mm , bolt bsw s/b u/m hex hd with hex nut 1/4" x 3/4"

CTN :43502316

19 Jan, 2026 NA

Imphal - Manipur

Tender For supply of structural steel work ms tubular post truss purlins , modular pvc wall panelling , aluminium u channel , aluminium 2 tier sliding channel , aluminium t channel , aluminium tower , binding wire , tapping screw , star screw , nails , mdf pre laminated particle board , synthetic enamel paint , thinner , paint brush , red oxide , nut and bolt 8mm , welding rod , iron cutter , drill bit , iron grinding , welding machine , black cushion chair , mat brown , jute mat , ply wood

CTN :43502930

19 Jan, 2026 NA

Gandhinagar - Gujarat

Tender For supply of windows handles 150mm left hand , oil putty , peg set 300 mm for ms , ptmtjet spray with 1 mtr tube , pvc ball cock float valve 50mm complete , pvc swr pipe 75mm dia , pvc bath cabinate 350 x 450 mm , pvc bathroom water shower 100mm , pvc connection 15x450mm long complete with nut bolt and washer , pvc connection 15x600mm long complete with nut bolt and washer , pvc cover suitable for all water storage tank 500 ltr complete , pvc flushing cistern 10 ltr cap , pvc grating 100mm , pvc grating 75mm , pvc swr pipe 110mm dia , pvc tee equal 110mm , pvc washer suitable 15mm bore bib tap , pvc waste coupling 40mm , pvc waste pipe corrugated 32 x 900 mm long , ss curtain bracket 25 mm dia , steel screw 25mm x 8g , steel screw wood 45mm x 8g , steel ms hinges butt 75 mm , urinal flat back 450 x 350 x300mm , whb 550x450x440mm , cp overhead shower , pvc water storage tank with lid 1000 ltr , bell joint repair clamp for di pipe 100 mm , gi plug 40mm , gi plug 50mm , di pipe k7 100 mm both end flange , di pipe k7 fitting tee 100 mm both end flange , bell joint repair clamp for ci pipe 100 mm , bell joint repair clamp for ci pipe 150 mm , bell joint repair clamp for ci pipe 200 mm , bell joint repair clamp for di pipe 150 mm , bell joint repair clamp for di pipe 200 mm , gate valve gun metal 50mm , gi socket screwed 50mm , copper sulphate , gate valve gun metal 15mm , eco clean 2300 herbal reagent 1 ltr , gate valve 25mm , gi bend 90 deg 20mm , gate valve gun metal 40mm , cpvc coupler 20mm , cpvc elbows 40mm , cpvc male thraded 20mm , gate valve gun metal 20mm , gi elbow 15 mm , gi socket 15mm , gi union 15mm , bleaching powder , cpvc elbows 20mm , cpvc female thraded 20mm , cpvc female thraded 32mm , cpvc female thraded 40mm , cpvc male thraded 32mm , cpvc male thraded 40mm , cpvc tee 20mm , cpvc tee 40mm , cpvc union 20mm , cpvc union 32mm , cpvc union 40mm , gate valve gun metal 25mm , gi socket 25mm , gi socket 20mm , gi union 20mm , cpvc valve 32 mm , cpvc valve 25 mm , cpvc coupler 32mm , cpvc male thraded 25mm , cpvc reducer socket 32x25mm , round up herbisite 1 ltr , m seal 150 gm , gi union 25mm , liquid defoaming agent , sodium hypoclorite solution , alum ferric solution , calcium hypochlorite , astronomical time switch based on lux level , bell ding dong call bell , cable copper flexible 3 core x2 point 5 sqmm , cable lugs alumn 120 sqmm , cable lugs alumn 150 sqmm , cable lugs alumn 185 sqmm , cable lugs alumn 240 sqmm , cable lugs alumn 25 sqmm , cable lugs alumn 300 sqmm , cable lugs alumn 35 sqmm , cable lugs alumn 50 sqmm , cable lugs alumn 70 sqmm , cable lugs alumn 95 sqmm , cable lugs ring type 100 sqm , cable lugs ring type 120 sqm , cable lugs ring type 150 sqm , cable lugs ring type 240 sqm , cable lugs ring type 25 sqm , cable lugs ring type 300 sqm , cable lugs ring type 35 sqm , cable lugs ring type 40 sqm , cable lugs ring type 50 sqm , cable lugs ring type 70 sqm , cable lugs ring type 95 sqm , cable lugs u type 10 sqmm , cable lugs u type 16 sqmm , capacitor 2 point 5 mfd , engine oil , batton holder , angle holder lamp batten bakelite , ht do fuse 10 amp , ht tape element 11 kv voltage grade insulation , led 9 watt bulb 6500k , led bulb 12 w , led street light 60 w , led street light 70w , led 2x 2 36watt led fitting , ht11 kv cold shrink indoor type cable end joint 95 sqmm , ht11 kv cold shrink outdoor type cable end joint 95 sqmm , ht 11 kv cold shrink straight through joint 95 sqmm , pvc tape roll 40 mm , spn db box 4 way , brass mortice lock four lever //bid details 2 / 125 vertical type , lock 6 lever 100 mm brass , paint se black 1 ltr pack , paint brush 25 mm , paint brush 50 mm , paint brush 75 mm , paint synthetic enamel og in 1 ltr pack , paint white 1 ltr pack , soft broom with grass , tarpentine

CTN :43521576

19 Jan, 2026 NA

Multi City - Multi State

Tender For supply of pre-fabricated steel tubular ffl 2 oblic 1 structure of size 2.40 x 2.40m , quick setting compound rapidite make acclerex cico fosroc , aggregate 20mm. stone aggregate to be crushed rock or gravel 20mm graded , aggregate 40mm. stone aggregate to be crushed rock or gravel 40mm graded , manufactured sand m sand confirming to is 383 2016 specifications for coarse and fine aggregates. , bricks cement pcc brick of size 230mm x 115mm x 75 mm with sharp corners , non skid ceramic tiles coloured 7 to 8 mm thick in floors , liquid water proofing compound is 2645 2003 , white cement packet 01 kg , pvc ceiling rose 2 obliq 3 terminal with pvc square box complete with screws , led tube light fitting 1 x 12 w 2 feet long complete with all accessories including led tube rod , pvc cable insulated and pvc sheathed 1.50 sq mm twin core with copper conductor , flexible wire pvc insulated twin core twisted of size 23 obliq 0.0076 with copper conductor , modular switch one way 6 amp 1 module , white cover plate with frame 2 module , white cover plate with frame 3 module , metal flush box 2 module , metal flush box 3 module , mcb double pole 230v ac 50 hz 16 amps 10ka confirming to is 8828 1996 , mcb distribution board in sheet metal enclosure two ways with blanks conforming to is 8828 1978 , ms screw 20 mm full threaded per pkt 100 nos conforming to is 723 1972 , tape insulation 2 cm width 10 mtr long isi marked , pvc casing caping 25 mm x 16mm , pvc casing caping square box 4 inch x 4 inch , pvc body exhaust fan 250mm sweep with lowers , vitreous china squatting pan orissa pattern size 580 x 440 mm white with integral foot rests , pvc valve less syphonic action type low level flushing cistern 10 ltrs capacity , 110mm dia upvc pipe 3 mtr long single socketed with cowl , 110mm dia upvc single tee , 110 x 110mm nahani trap with jali , 4 inch dia upvc bend , 15mm brass stop cock conforming to is-8934 1978 , 3 layer of pp r polypropylene random copolymer pipes sdr 7.4 , 20mm elbow suitable for 20mm dia ppr pipe conforming to is 1239 1989 , 20mm socket suitable for 20mm dia ppr pipes conforming to is 1239 1989 , 20mm equal tee suitable for 20mm dia ppr pipe conforming to is 1239 1989 , 20mm union suitable for 20mm ppr pipes conforming to is 12391989 , ppr end plug 20mm conforming to is 1239 1989 , ppr pipe clamp suitable for 20mm piping , bib cock 20 mm with flange conforming to is 8931 1978 , gi reducer socket 15 obliq 20mm , gi reducer elbow 15 obliq 20mm , pre fabricated man hole cover 6 feet x 4 feet made of isa 40x40x6mm frame , rotational moulded polyethylene water storage tank double layer , ppr tank connector 20mm with check nut and washer , white lead safeda , thread cotton ball 100 m long , vitreous china wash hand basin whb white flat back size 550x400 mm , 20mm dia pillar taps of ptmt of any colour high pressure screwed for iron pipe , 110mm dia upvc swr pipe single socketed pipe type a in any length with rubber joint , 600x450mm size looking mirror mounted on pvc with pvc shelf assembly including all fittings all as specified

Check Nut Scrap Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector

Central Government/Public Sector

State Government