Latest crusher motor Tenders | Government crusher motor Tenders

Central Government/Public Sector

CTN :40387629

02 Jun, 2025 NA

Chhindwara - Madhya Pradesh

Tender For corrigendum : supply of rotating assy ci part no rae , intermediate stage assly cast iron part no is149b6 , bearing housing s and d cast iron part no hpb62 , sleeve nut s and d en8 part no hpb64 , gland flange s and d cast iron part no hpb65 , balancing valve bronze part no hpb69 , impeller cast iron part no hpb611 , guide vanes cast iron part no hpb613 , stage ring s cast iron part no hpb618 , disc seat bronze part no hpb619 , stage bush cast iron part no hpb620 , neck ring stage ring d cast iron part no hpb626 , shaft sleeve d cast iron part no hpb628 , seal cage bronze part no hpb631 , balance valve bush bronze part no hpb634 , stage ring big cast iron part no hpb635 , shaft sleeve s cast iron part no hpb66 , discharge bush bronze part no hpb636 , tie rod part no hpb827

State Government

CTN :40227801

10 Jun, 2025 49.58 Lacs

Gandhinagar - Gujarat

Tender For corrigendum : various routine/preventive and breakdown maintenance work on as and when require basis at chp-gtps - replacement of hammer rings for stage ii crusher , replacement of hammer rings for stage i crusher , replacement of screen plate / breaker plate/kick off plate of stage i and ii crushers , replacement of rotor of stage i crusher with disassembling of removed rotor and assembling of new/repaired rotor , replacement of drive end side bearing / pedestal of crusher rotor or complete gear coupling set of crusher or repositioning of dislocated rotor of crusher , replacement of non drive end side bearing/pedestal of crusher rotor or complete alignment of crusher motor with crusher rotor , replacement of broken hammer rings of stage i and ii crushers (stage i crusher up to 12 nos.of hammer rings and stage ii crusher up to 06 nos. of hammer rings at a time) , replacement of rail of rail table of wagon tipplers 1/2/3/4 (in one side full length) , replacement of clamping rubber pads of clamp for wagon of wagon tipplers , replacement of whole resting pads for wagon of side beam of wagon tipplers , replacement of spill plate roller of wagon tipplers , repairing/preparation/ fitting and replacement of hooks/rods/turn buckle, chain, sling rope ,spring assembly etc. of vibrating trays and crusher house trays , spillage control at various locations , miscellaneous cutting/welding work require at various locations , replacement of gearbox in conveyor no. 2a/b,11a/b,12a/b,13,14/15,16a/b,17a/b ,18a/b,drc/apron/rg/,wagon tipplers,stacker-reclaimer , replacement of gearbox in conveyor no.,5a/b,8a/b,10a/b,shuttle conveyor 1/2,belt feeder 1/2 ,roller screen, mrc 3/4/5,wobbler feeder ,dribble conveyor 1/2 , replacement of slow speed coupling set (two halves) of drive pulley , replacement of coupling bolts and rubber bushes of slow/high speed coupling(input/output coupling ) in conveyor no.2a/b,11a/b,12a/b,13,14/15,16a/b,17 a/b,18a/b,drc/apron/rg/,wagon tipplers,stacker-reclaimer , replacement of coupling bolts and rubber bushes of slow/high speed coupling(input/output coupling ) in conveyor no.,5a/b,8a/b,10a/b,shuttle conveyor 1/2,belt feeder 1/2 ,roller screen, mrc 3/4/5,wobbler feeder ,dribble conveyor 1/2 , replacement/removing/refitting of various size and type of fluid coupling , replacement or removing & refitting of any internal/bearing/input/ output oil seal of various size and type of gear box , overhauling of dismantles old/used gearbox in all respect with fitment of input and output coupling. , replacement of drive pulley , replacement of drive end side bearing of drive pulley or repositioning of dislocated drive pulley , replacement of non drive end side bearing/any side pedestal of conveyor drive/non drive pulley , alignment of motor/ gearbox/drive pulley including decouple/couple of coupling , nut bolt and drive system checking with replacement of broken nut bolt in all 04 wagon tipplers no.1/2/3/4 as per scope , lifting and releasing of gravity take up of any conveyor belt for locking and de locking of belts for other than belt replacement work , loosening and tightening of horizontal type screw take assembly of any conveyor belts for other than belt replacement work , work of dismantling and re erection of new/repaired apron pan from existing apron feeder of wagon tippler , repairing of upper/lower structure/cone plates of damaged/bend apron pan , replacement of carrying roller of apron feeder , replacement of worn out/ damaged ti roller and garland rollers. , replacement of worn out/ damaged impact rollers , replacement of worn out/ damaged return rollers , replacement of various worn out/ damaged ti roller stands , replacement of various worn out/ damaged impact roller stands , replacements of various worn out/ damaged return roller stands , replacement of various worn out skirt rubbers [10 m each] and skirt rubber with angle , preparation and replacement of guide rollers with bracket in place of worn out/ damaged gu

Central Government/Public Sector

CTN :40446684

14 Jun, 2025 10.46 Crore

Sidhi - Madhya Pradesh

Tender For procurement of spares of 20 90 draglines - shock absorber, part no.10302717 , packing washer, part no.10400734 , thrust ring, part no.10400953 , coupling hyd. pump and motor, part no.1055525042 , bushing, part no.10586415 , stud, part no.10586435 , nut 10600201, part no.10600201 , thrust washer, part no.10600710046 , gear shaft, part no.106007101 , ring, part no.106007102 , pinion shaft, part no.1060071031 , flange, part no.106007105 , washer, part no.106007106 , bushing, part no.106007107 , bushing, part no.106007108 , flange, part no.106007109 , bushing, part no.106007110 , washer, part no.106007120 , copper rivet, part no.1060077153 , thrust washer, part no.10600910093 , stud, part no.106009105 , stud, part no.10600910501 , pinion shaft, part no.10600912 , cleat, part no.10601104 , cleat, part no.10601105 , cleat, part no.106011170 , coupling half, part no.106018105 , copper rivet, part no.1060185022 , air cylinder, part no.106018550 , repair kit air cylinder, part no.1060185503 , swing hook wedge strap, part no.106020103 , copper gasket, part no.106023300217a , shoe hold cylinder, part no.10602401sb , coupling bolt, part no.10602520028 , nut, part no.10602529 , shoe support bracket, part no.10602701 , half coupling, part no.10602901 , coupling pad, part no.10604200235 , half coupling, part no.106029101 , bolt, part no.1060615551 , bolt, part no.1060615553 , nut, part no.1060615554 , nut, part no.1060615552 , drag pulley, part no.10606401 , roller assy., part no.1060710301 , coupling bolt, part no.106086100122 , repair kit air cylinder, part no.1064077503 , air cylinder, part no.106407750sb , copper gasket, part no.1064245014 , locking plate, part no.106502031 , cover, part no.10650209 , copper gasket, part no.106523001204 , strap rope liner, part no.110316421 , pressure guage, part no.1103800000000000 , impeller, part no.56c03602412 , blower impeller of drag or hoist, part no.56c43602412 , blower housing assy., part no.56c43602413 , impeller, part no.56c83602412 , clamping gear, part no.5bs09048801 , brush holder, part no.5bs11211706 , coupling pin, part no.8bs27739501 , half coupling, part no.bg1123a5 , cup packing, part no.m3003402 , electrical distributor, part no.pt11120 , hydraulic pusher, part no.te25t2 , air solenoid valve, part no.vv325h , bushing, part no.10606408 , roller assy, part no.1060710302 , blower housing comp assy., part no.56c03602413 , non-return valve e155ash, part no.e155asb , safety valve for stage 1, part no.k5a0405000 , washer thrust, part no.10041111 , roller, part no.10580209 , stud, part no.10600910502 , stud, part no.10602160018 , nut, part no.10602160019 , section, part no.106072302 , dump pulley, part no.106061555 , section, part no.106072301 , section, part no.106072303 , section, part no.106072304 , stand, part no.10650221 , stand, part no.10650222 , guide, part no.110316401 , axle, part no.10606142 , ring, part no.10650206 , ring, part no.10650210 , pinion shaft lh, part no.106009121 , half coupling, part no.1060181051 , clamp, part no.106061594 , compressor without motor, part no.4vu159m4 , rib assembly, part no.10606140029

CTN :40361990

06 Jun, 2025 NA

Visakhapatnam - Andhra Pradesh

Tender For tender for supply of impeller , nozzle bronze lff spray , ventilation air dust fileter , port hole 250mm dia with coaming , filter , shock absorber damper , screw driven 1-2-7 , contact main , bridge type , screw driven , contact bridge type , gasket , gasket , washer spring 24h 65 , valve disk , hose flexible metalic dn50 pn 25 , distance piece/ bush distance , washer protective , washer protective , washer protective , contact movable , flange (collar) , cock , thrust bearing bush , sealing , disk , disk , shock absorber damper , shock absorber damper , valve non return , impeller , impeller , disk , valve suction 2nd stage , packing collar of regulating slide valve , durite coupling , stop angle valve with union ends , durite 22 to 27mm , valve disk , washer , impeller for vaccum pump wheel impeller , valve disk , joint nipple and edge union tap brass py 100 dy 25 , union branch bronze dy 32 , union branch bronze dy 6 , union intermediate steel dy 32 , joint nipple and edge union steel dy 10 , unit injector automizer , pipe distributor 1.630mm 8x670 , pipe , pipe , pipe connection starting servo motor tospeed governor

Central Government/Public Sector

CTN :40389133

09 Jun, 2025 18.55 Lacs

Chandrapur - Maharashtra

Tender For supply of spares of maxflow make pump model 149hpb5 ss - intermediate stage assembly ss316 part no. ss149hpb538isa1 , bearing cover s and d part no. ss149hpb51bc , bearing housing s and d part no. ss149hpb52bh , sleeve nut s and d part no. ss149hpb54sln , gland flange part no. ss149hpb55gf , shaft sleeve s part no. 149hpb56 , shaft part no. ss149hpb58s , balancing valve part no. ss149hpb59bv , impeller part no. ss149hpb511i , stage ring s ss316 part no. ss149hpb518srs , disk seat bronze part no. ss149hpb519ds , stage bush br part no. 149hpb20 , sleeve key ss316 part no. ss149hpb521sk , stage ring big ss316 part no. ss149hpb522srb , impeller key ss316 part no. ss149hpb525ik , stage ring d ss316 part no. ss149hpb526srd , shaft sleeve d ss316 part no. ss149hpb528ssd , seal cage bronze part no. ss149hpb531sc , balance vlave bush bronze part no. ss149hpb534bvb , discharge bush bronze part no. ss149hpb535db bid number/ & ( * ) : gem/2025/b/6245886 dated/ + : 18-05-2025 bid document/ 3 3 1 / 25

State Government

CTN :40095274

03 Jun, 2025 NA

Birbhum - West Bengal

Tender For corrigendum : providing electro-mechanical accessories and others at pump house- i and ii for bahadurpur w/s scheme at murarai -i block under bolpur mechanical division phe dte. - supply and delivery at site of the following submersible pumping machinery and electrical accessories as per approved vendor list of phed, submersible pumping machinery directly coupled with water proof suitable size motor having following specification :- pump:duty condition -25.74 m3/hr, head- 57 mtr, shaft-stainless steel, impeller- s.s / gm, outlet size: 65mm / 80mm., motor:submersible type 3 ph , 50hz, 415 volt 10% 2900 rpm motor must be suitable for operation with star delta starter.(test certificate along with characteristic curve should be submitted at the time of delivery)., 1.1kv grade 4 sq.mm x 3 core water proof flat submersible cable for above pump-motor set., 1.1kv grade 10 sq.mm 3 core xlpe insulated aluminium armoured cable conforming to is 7098 (part-i) 1988, with upto date amendments., supply and delivery of the following valves, pipes and gauges etc at site, 3mtr long 80mm dia upvc standard type column pipe [cream color] with both side threaded and one end side socketed with registered kpmg, 1.5 mtr long 80mm dia upvc standard type column pipe [cream color] with both side threaded and one end side socketed with registered kpmg., 80mm dia. ci top & bottom adopter., heavy type suitable dia. ms suspension clamp along with nuts bolts and washers., 80mm dia. cidf non-raising sluice valves, pn 1.0 rating (conforming to is:14846) for delivery pipe line and wash out line.(moc & tc needed for valve)., 80mm dia. cidf single door swing non return valve, pn 1.0 rating (conforming to is:5312).(moc & tc needed for valve)., cidf 90 bend- 1no., ci flanged tee- 1no., blank flange-1no., ci/ ms flanged short piece 0.50 mtr.-1no, ci/ ms flanged pipe 1mtr.- 1 no. etc (as per is specification and certification registered) for construction of delivery pipe line and wash out line, heavy type 250mm dia./suitable split type tube well cover with clamping arrangement including supply of nuts, bolts and washer as per departmental design., anti snapping safety device for pump set by supplying suitable size of ms angle busket and nylon rope of required length including supplying of nuts, bolts and all other materials, 150mm dial pressure gauge [range 0-7kg/cm ] with glycerine filling inside the dial including brass cock and fitting complete [this cost includes 15mm. dia g.i. pipes and specials]., making brick pillar 0.25 x 0.25 x 0.75 mtr/suitable hight for supporting of valves and pipes with 12mm thick plaster and net cement finish complete., making cc foundation for support of the kiosk box after excavating the earth upto a depth of 0.6 mtr below the gl including supply of all materials complete with 12 mm thick cement plastering with net cement finishing complete as per direction of eic (size: 3 x 1 x 5)., suitable kiosk box for cable connection of submersible pump motor set with degree of protection ip 65 including suitable legs and 6 nos. al. bus bar for 32 amps and all necessary earthing arrangement and insulator as per direction of eic., laying of one no. cable 10 sqmm 3 core ( departmental supply) in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of thecable with 8 (eight) nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed., carrying and fixing three phase submersible pump 7.5 hp mug starter as per direction of eic ., installation of submersible pumping machinery to newly sunk tubewell along with column pipes (as required), top cover, valves, and specials of above with protection pipe and supply of ms clamp, nut bolt, cable gland socket etc. making inerconnection of the pump delivery line to pump collecting main line near tubewell with supply of all necceasary pipe, reducer/enlarger, gi/ms

CTN :40133554

19 May, 2025 10.58 Crore

Karwar - Karnataka

Tender For corrigendum : procurement of main engine spares - clamp, bolt hax soc, valve keeper wedge, diaphragm, hand pump, filter element, split pin 5 x 45 din 94, contam indicator, actuating cylinder, washer, exh pipe bellows, insert paper, first plate, end plate, base complete, guide ring, end plate, ring sealing, first plate, rubber bellows, end plate, first plate, nut, circlip, snap ring 32x1.5 din 471, circlip, snap ring 42x1.75 din 472, circlip for set w6, snap ring 68 x 2,5 din 472, incandescent lamp, o-ring 11.3x2.2 for set w6, plug, screw m10x30, screw m12x50, screw, hex nut, nut, hex nut, nut (m12), stud, countersunk hd screw, adjusting washer, rotary seal, pin spring, pressure monitor 2.2 bar, washer a 16, pressure spring, oil pump, oil filter (element), pressure sensor 15 bar, pressure sensor +/- 70m bar, pressure sensor, drain valve, switch, pressure sensor, cylindrical pin, conical spr washer, seal ring, ring sealing a12x15.5, ring sealing (crank case) a14x18, ring sealing, sealing ring, ring sealing (crank case) a20x24, sealing ring, ring sealing a26x31, sealringa26x34forsetw6, washer a, ring sealing (crank case) a30x36, ring sealing (crank case) a38x44, ring sealing a45x52, ring sealing a52x60, taper facecomp.ring, ring seal, o-ring, sealing ring for set w6, grease nipple am 6x1, nozzle holder, bearing angular contact roller, bolt hex gal cu 5 bk, adjusting washer 42x 52 x 0,1 din 988, cinical spr. washer, conical spr. washer, screw, hex screw, sealant pipe thread loctite 586, clamp, sealing paste gd block, silcone rubber loctite 5970, valve, washer, washer, washer, turbine wheel, ring snap, nut, speed transmitter dm52, cylinder head complete, carbon scrapper ring, sealing ring for set w5, gasket, gasket for set w5, bolt m20 1.50x103.0 lg 18 conrod, bushing con rod 75.00, con.rod brg.upper half, idler gear, bolt adjusting, tube asm cyl head fuel return, adapter, trust member, flap, shaft, bracket turbo speed sensor, pressure valve, sleeve guide oil clr, cover, bolt cylinder head, grommet, sealing ring, adapter 60deg m14x1. 5, cylinder, shaft, flange sealing, bearing bushing, bearing bushing, bearing bushing, shaft, cable for monitor system, coolant pump shaft, impeller, impeller, wiring harness for engine sensor, actuating cylinder, insert (crank case breather), diaphgarm, spacer bushing, gasket, flow restrictor, sealing ring, microswitch, benjo screw, tab washer, grommet 6, grommet, grommet, grommet, sleeve rubber, grommet, grommet, seal oil, union 32 g, o-ring for set w5, o-ring for set w6, o-ring, o-ring, o ring 26 x 2.5 mmn 294, o-ring, o ring, o ring, o-ring, o ring 39.2x3, o ring, o ring, o-ring, o - ring, o-ring 60x4 for set w5, o ring, o-ring, o ring, o ring, o ring, o ring, o ring, o ring, o-ring for set w6, o ring, hose line, hose, hose line, regulator fuel retur n 0.5 bar, valve check 0.2 bar rhdk 18-l 0.2, spacer, exhaust bellow. dn 400, washer a cop, gasket for set w5, gasket for set w5, gasket, paper pack centrifugal spinner filter, screw, nut, compensating washer, washer, washer, repair kit, nut, sealing cone 22mbn 15005, straight connector, adaptor 10 / 6 n 15007, transition socket, union, clamp, vibration damper, cylinder head, exhaust bellows, injector, piston, coolant pump high-temp circuit, washer, impeller for sea water pump, bearing body, gear, rotary seal, level monitor, pressure sensor, cover for solars, actuator vlv, corrosion inhibitor conc. coolant cs100, pressure sensor, track-ball, wiring harness for on-engine sensor, conrod bearing size 0-0(s/sx00040714), gasket, flow restric valve, link (x52408100007), support plate, valve collet, exhaust compressor, hex crew, bearing camshaft std, valve spring outer, hp line, non return valve, valve, clamp, bracket wiring harness, diff-press monitor, screw, snap ring 48x1.75 din 472, spring pin for set w6, swing foll, grooved pin, woodruff key, sealing ring, repair kit, union, gasket for set w6, hex screw, union, tube asm sol oil supply, nut m16 04-2 din43

State Government

CTN :40071835

02 Jun, 2025 NA

Birbhum - West Bengal

Tender For corrigendum : providing and installation of electro-mechanical accessories at cwr site and allieds works at ekpara pwss, block-rampurhat-i under bolpur mechanical division - supply and delivery of openwell submersible pumping machinery set suitable for wet pit installation complete with stainer along with all accessories with following specification: pump : discharge (q) : (1800-1280) m3/hr. & head (h) : (19-38) mtrs.method of starting : sd, shaft-stainless steel-ss-304, impeller- crome steel/ci/s.s / bronze, suc & del size- 90/80 mm dia, type of position-horizontal. mechanical sealmotor : 12.5hp (suitable for open well)operating voltage : 415 ( 10 %), phase : 3ph, 50 hz 6%speed : 2800 rpm, method of starting : s/dmake : ksb / grundfos / texmo / cri / kbl / mbh / or any approved vendor. ( n.b : manufacturers test certificate along with charecteristics curve, moc and gurantee certyificate have to be submitted at the time of delivery.), supply & delivery at site of 35 mm x 3.5 core size aluminum armored, xlpe insulated 1.1 k.v. grade cable, conforming to is 7098(i) as per direction of eic.(make:- gloster / polycab / mescab / or any approved vendor list of phed.) ( n.b : manufacturers test certificate have to be submitted at the time of delivery.), supply & delivery of 100a kit-kat rewireable (porcelain fuse carrier & base) (make:- havells / l&t / or any approved vendor list of phed.), supply & delivery of 100 amps re-wireable porcelain fuse unit type tpn main switch with steel sheet enclosure (conforms: is/iec600947-1&3). (make: havells /approved vendor list of phed.), supply & delivery of re-wireable type tpn changeover switch 100 amps 415v, 50hz, 4 pole offload with steel sheet enclosure (conforms: is/iec60947-1&3). (make: havells /approved vendor list of phed.), 100 amps, 4way, wall mounted copper busbar chamber with steel sheet enclosure (conforms:is/iec:60947-3). (make: havells /approved vendor list of phed.), supply and delivery of the following pipes, valves, pipes and gauges etc at site-- (make: approved vendor list of phed.), 100mm dia m.s. black pipe p/e conforming to is:1239 part-1 (2004), heavy (c class)., 150mm dia m.s. black pipe p/e conforming to is:1239 part-1 (2004), heavy (c class)., 100mm dia m.s. blank flange 15mm thick perforated as per is1538., heavy type suitable dia. ms suspension clamp along with nuts bolts and washers., 100mm dia. cast iron double flanged manually operated rising spindle type sluice valve generally conforming to is: 14846, having body, door, dome / bonnet, gland in graded cast iron to is 210 gr. fg 260, four faces of ss aisi 304 and spindle nut of gunmetal to is 318 gr. ltb 2, outside screw rising stainless steel aisi 304 spindle, valves suitable for a maximum working pressure of 10 kg/cm (seat test) & body tested to 15 kg/cm . flanges faced and drilled to is:1538 table 4 & 6. valves tested by closed end method only. (moc & tc needed for valve)., 100mm dia. cast iron double flanged single door swing non-return valve generally conforming to is:5312 part i, having body, door, cover in graded cast iron to is 210 gr. fg 260; body & door rings of stainless steel to ss aisi 304 , hinge pin of ss aisi 304, valves suitable for a maximum working pressure of 10 kg/cm (seat test) & body tested to 15 kg/cm . flanges drilled to is 1538 table 4 & 6.(moc & tc needed for valve)., 100 mm dia dismantling joint pn-1.0 ci dismantling joint complete galvanised , stud, nut and washer and follower flanges, drilled to is:1538 table 4 & 6. ( at delivery side of pump ), supply & fixing of perforated gi cable tray tee with perforation not more than 17.5% suspended from ceiling with two nos. suspenders & 25x25x3mm angle iron for supporting the cross member incl. s&f gi connector, 6mm dia ms suspender, bolts & nuts, steel fastener etc. as required of the following size. incl. al painting of ms support. [200x50x1.25mm x 3mtr long

State Government

CTN :40213009

02 Jun, 2025 NA

Chennai - Tamil Nadu

Tender For procurement of mgf backwash pump for cwbd plant - 1 no-mgf b/w pump for cwbdplant,equipment ; 30-j-652a/b,pumpmodel;cn-200-250-g1s2l4 orequivalent,suction/disharge,flange;250/200, class150,flow rate q;410cubicmetre/hour,head;18metre,pressure;1.8kg/ centimetre squar,end suctionback pull out pump,end covers with oilseals,lubrication;oil,impeller;closed,gland packing;inmarcostyle102,motor hp/speed;40/1440 rpm,moc; cast iron-casing,bearinghousing with bracket,back plate withgland housing,end covers,gland(flange, follower).ss304-shaft,sleeve,wear ring(impellor,casing),impeller,bearing locknut,impeller lock nut/key andfasteners

corporations/Associations/Others

CTN :40186773

21 May, 2025 NA

Cuddalore - Tamil Nadu

Tender For tender for supply of critical spares for condenser vacuum pumps - condenser vac pump key , condenser vac front bearing outer cap , condenser vac pump front bearing housing , condenser vac pump bearings set , condenser vac pump front brng inner cap , condenser vac pump front end shield , condenser vac pump front port plate , condenser vac pump gland packing , condenser vac pump stuffing ring , condenser vac pump rear port plate , condenser vac pump rear end shield , condenser vac pump flat gasket , condenser vac pump gland packing box , condenser vac pump gland packing cover , condenser vac pump shaft sleeve , condenser vac pump rear brng inner cap , condenser vac pump rear brng housing , condenser vac pump rear retaining ring , condenser vac pump round nut , condenser vac pump lock washer , condenser vac pump rear brng outer cap , condenser vac pump space washer , condenser vac pump felt ring , condenser vac pump v rings , condenser vac pump key , condenser vac pump flexible valve plate , condenser vac pump intercepting plate , condenser vac pump o rings , condenser vac pump flange cover , condenser vac pump flat gasket (ptfe) , condenser vac pump front retaining ring , condenser vac pump v-ring , condenser vac pump rc pump kg65-50/16 , condenser vac pump r/c pmp impeller , condenser vac pump r/c pmp mechni seal , condenser vac pump r/c pmp o-rings set , condenser vac pump adaptor , condenser vac pump coupling set , condenser vac pump y type strainer , condenser vac pump buterfly val dn 250 , condenser vac pump buterfly vale dn 80 , condenser vac pump check valve dn 250

Crusher Motor Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors