Latest drilling hole Tenders | Government drilling hole Tenders

State Government

CTN :45730369

09 Jul, 2026 NA

Kannur - Kerala

Tender For providing and fixing following rating and breaking capacity mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel. making connections. etc. as required. 250 amp, 50 ka

Central Government/Public Sector

CTN :45713879

20 Jul, 2026 NA

Jorhat - Assam

Tender For repairs to compound wall, fencing and gate with connected items in domestic area and omq area at afs under ge (af) jorhat - demolition of brick work built in cement mortar of any description complete all as specified and as directed., m&l for brickwork (old size) with sub class b bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar (1:6) complete all as specified and as directed., all as per serial item no. 2 here-in-before but except bricks, using old serviceable brick as retrieved from demolition.note : old serviceable bricks obtained from serial item no. 1 above shall re-used., taking down cement plaster on brick or stone or concrete surfaces of walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed., m&l for rendering 15mm thick on fair face of brick works or concrete surfaces of walls with cm (1:4), finishing the surface even and smooth without using extra cement complete all as specified and as directed., m&l for preparation of new plastered surfaces of walls and applying two coats of cement base paint over and including one coat of alkali resistance primer complete all as specified and as directed., demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed., m&l for plain cement concrete (1:2:4) type b-0 (using 12.50mm graded stone aggregate) used as in benching and coping including necessary formwork complete all as specified and as directed., m&l for brickwork with sub class b bricks, straight or curved on plan to any radius in half brick thick walls, built in cm (1:4) complete all as specified and as directed., m&l for dismantling posts or struts (wood, steel or rcc) any section, including taking out embedded portion and making good to disturbed ground surfaces complete all as specified and as directed., m&l for plain cement concrete (1:3:6) type c-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, etc. complete all as specified and directed., s&f hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing, etc. wind ties for roof including securing bolts posts and struts in fencing of size 65x65x6mm including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to fe-290 gde e-165 complete all as specified and as directed., dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed., s&f 11mm to 15mm dia of shank mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and onehexagonal or square nut, but length of bolt exc. 5cm but n. exc. 10cm complete all as specified and as directed., excavating in post holes (or similar holes) each n. exc. 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc. 50m and making good surface as in soft/loose soil complete all as specified and as directed., m&l for preparation of new steel and iron surfaces of any description over 10cm width or girth not otherwise described for and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and as directed., m&l for mild steel tmt bar 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends binding wit

CTN :45679372

02 Jul, 2026 20.16 Lacs

Delhi - Delhi

Tender For supply and replacement of defective parts of kirloskar make transformers of 1000/750/500 kva capacity at ugc & cag building, new delhi. - supply and fixing of over current earth fourth relay 24 dc l&t make etc complete as reqd. , supply and fixing of 11 kv indoor single phase resin cast current transformer 300/5amp etc complete as reqd., , supply and fixing of transformer 500 kva 11/0.433 kv wt1 scanner & rtd sencer lead., , supply & installation of suitable rating of 500 kva 11/0.433 kv lv bussing porcelain or epoxy-cast resin comply with is-1180 complete as required, , supply and fixing of suitable rating of 500 kva 11/0.433 kv lv flexible porcelain or epoxy-cast resin comply with is-1180 complete as required., , dismantling /loading and unloading of 500kva, 11kv/433volt, 3phase, 50hz, cast resin dry type kirloskar make indoor transformer hv/lv coil/core etc and repair of crack in hv/lv winding/core and putting cast resin/resin hardener, reassembling all the dismantle parts accessories confirming to is 11171 and iec 60076 etc including all tests i.e voltage ratio, magnetic balancing, vector group, ir magnetizing current, winding resistance etc complete as reqd., , supply & installation of 630a vcb vacuum interrupter etc complete as reqd., , sh-2 (old cag bldg), , supply and replacement of 750- 1000 kva transformer oil gas kit etc complete as reqd., , checking in 750-1000 kva transformer all type of protection etc complete as reqd., , supply and replacement of lv bushing oil seal in 750-1000 transformer etc complete as reqd. no.ryb) (4, , supply and replacement of hv bushing oil seal in 750-1000 transformer etc complete as reqd. (3 no. r,y, b), , supply and replacement of off load tape changer in 750-1000 kva transformer etc complete as reqd., , replacement of transformer oil in oltc top-up of main tank etc complete as reqd., transformer oil filtration and dehydration of 750 kva & 1000 kva transformer using high-vacuum oil filtration plant, including removal of moisture, dissolved gases, sludge and impurities from transformer oil, circulation of oil through filtration machine, achieving required bdv value, testing before and after filtration, manpower, tools & tackles, consumables, complete as required at site., , complete servicing, overhauling, cleaning, contact checking, lubrication, insulation resistance testing, contact resistance testing, functional testing and commissioning of oil circuit breaker (ocb), complete as required at site., , supply & installation of male contact, , supply & installation of female contact, , supply & installation of over current earth fault relay, , supply & installation of 24 volt dc power pack unit etc complete as reqd., , supply and fixing of transformer wti relay etc complete as reqd.., , supply and replacement of transformer oti relay etc complete as reqd.., , providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, ics=100% icu and operational voltage 690v etc. as required., , (make: schneider electric-nsx /siemens / lk/ abb/hager)

CTN :45635494

30 Jun, 2026 NA

Kolkata - West Bengal

Tender For supply of split air conditioner, wall mount type (v3) isi marked to is 1391 (part 2) (q2) , unitary air conditioner (window ac) (v3) isi marked to is 1391 (part 1) (q2) , servo motor operated automatic line voltage correctors conforming to is 9815 (part 1) - single phase applications (q3) , material and labour for sub-main wiring surface type with two run of pvc insulated, unsheathed, frls single core and one run of 4.0 sqmm copper conductor , supply and fix single pole and neutral enclosure 240 volt, 20 amps with a two pin and earth plug and socket complete with one single pole mcb , m and l cutting chases, pinning in making good to facing where required and pointing in cement mortar 1-3 to ends or edges of landings, steps, cils, sunshades sheleves, lintels, etc , material and labour for sub-main wiring surface type with two run of pvc insulated.unsheathed, frls single core and one run of 6.0 sqmm copper conductor , m and l for stand bracket fabricated from structural steel section suitable for 3 ton ac outdoor unit including nut, bolt, washer, welding. bedding cold or hot , supply and install hi wall split units indoor and outdoor complete with cordless remote control unit with inbuilt air ioniser and plasma filter 5 star cap 3tr , supply and fix single pole and neutral enclosure 240 volt, 40 amps with a two pin and earth plug and socket complete with one single pole mcb , supply and install vertical tower type unit indoor and outdoor complete with cordless remote control unit, inverter 1 ph units 220v- 240v capacity 2tr , s and f motor starter 25 amp with on off push type switch, modular type two module make make legrand-gm-havells , s and f socket 25 amp modular type two module make legrand-gm-havells , s and f metal flush box, modular type four module make legrand-gm-havells , s and f cover plate with metal frames, modular type four module make legrand-gm-avells , m and l for stand-bracket fabricated from structural steel section suitable for 1.5 ton- 2 ton ac outdoor unit including nut, bolt, washer, welding. bedding cold or hof, drilling holes for bolts , supply and fix power socket 240 volt ac 25 a 2 module all as specified and directed , supply and fix 25 a motor starter 2 module all as specified and directed , supply and fix modular white cover plate metallic frame 2 module all as specified and directed

Central Government/Public Sector

CTN :45598119

30 Jun, 2026 8.22 Lacs

Tiruvallur - Tamil Nadu

Tender For supply, installation , tesgting , commissioning of cold storage room (equipment) in the old boys hostel at central university of tamil nadu, thiruvarur - coold storage room size (18l *11w * 9h) feet, supply of puf panels, door, refrigeration unit, control panel with accessories, installation charges of puf panels, doors & refrigeration units, labour charges for loading, unloading, labour charges for copper piping laying work, n2 pressure test, leak test, leak arrest, again n2 pressure hold, vaccuming, gas charging and commissioning of the unit, additional refrigeration pipe with accessories, transport charges, supplying and fixing of following sizes of water pipe of upvc ( sch 40) conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required., 25 mm, electrical work, supplying and fixing of following ways surface/ recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs (but without mcbs and incomer ) as required ., 12 way (4 + 36), double door (power & ups), providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, ics=100% icu and operational voltage 690v etc. as required., 100 a, 16 ka,tpmccb , supplying and fixing following rating, four pole, 415 v, mcb in the existing mcb db complete with connections, testing and commissioning etc. as required., 63a, supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth,metal enclosed plug top along with 30 a"c" curve, tpmcb in sheet steel enclosure,on surface or in recess, with chained metal cover for the socket out let and complete with connections, testings and commissiong etc required, 4 x 16 sq. mm + 2 x 6 sq. mm earth wire (incommer for power & ups line to db box)

State Government

CTN :45558196

22 Jun, 2026 NA

Medininagar - Jharkhand

Tender For supply of list of approved construction materials for the preparation of schedule of rates for the year 2026, basic rates of which to be approved by the state level schedule rate committee (materials should conform to relevant b.i.s., mord and mort&h specifications). the rates will be inclusive of royalty but exclusive of all taxes, g.s.t,overhead and contractor's profit. "rates are at source"quarry/ crusher plant. - stone boulder of size 150 mm and below at source quarry, supply of quarried stone 150-200 mm size for hand broken at source quarry, boulder with minimum size of 300 mm for pitching at source quarry, coarse sand i) at source, coarse sand ii) at source , fine sand at source quarry, moorum at source quarry, gravel/quarry spall at source quarry, granular material or hard murum for gsb works at source quarry, fly ash conforming to is:3812 (part ii & i) at hmp plant/batching plant/crushing plant, filter media/filter material as per table 300-3 (mort&h specification) at crusher., close graded granular sub-base material 53 mm to 9.5 mm/4.75mm at crusher., close graded granular sub-base material 37.5 mm to 9.5 mm at crusher. , close graded granular sub-base material 26.5 mm to 9.5 mm at crusher., close graded granular sub-base material 9.5 mm to 4.75 mm at crusher., close graded granular sub-base material 9.5 mm to 2.36mm at crusher., close graded granular sub-base material 4.75mm to 2.36mm at crusher., close graded granular sub-base material 4.75mm to 75 micron at crusher., close graded granular sub-base material 2.36 mm & below at crusher., stone crusher dust finer than 3 mm with not more than 10% passing 0.075 mm sieve at crusher., coarse graded granular sub-base material 2.36 mm & below at crusher., coarse graded granular sub-base material 4.75 mm to 75 micron at crusher., coarse graded granular sub-base material 4.75mm to 2.36 mm at crusher., coarse graded granular sub-base material 9.5mm to 4.75 mm at crusher., coarse graded granular sub-base material 26.5mm to 4.75 mm at crusher., coarse graded granular sub-base material 26.5 mm to 9.5 mm at crusher., coarse graded granular sub-base material 37.5 mm to 9.5 mm at crusher., coarse graded granular sub-base material 53 mm to 26.5 mm at crusher., aggregates below 5.6 mm at crusher., aggregates 22.4 mm to 2.36 mm at crusher., aggregates 22.4 mm to 5.6 mm at crusher., aggregates 45 mm to 2.8 mm at crusher., aggregates 45 mm to 22.4 mm at crusher., aggregates 53 mm to 2.8 mm at crusher., aggregates 53 mm to 22.4 mm(grade iii) at crusher., aggregates 63 mm to 2.8 mm at crusher., aggregates 63 mm to 45 mm (grade ii)at crusher., aggregates 90 mm to 45mm(grade i) at crusher., aggregates 10 mm to 5 mm at crusher., aggregates 11.2 mm to 0.09 mm (key aggregate type b) at crusher., aggregates 13.2 mm to 0.09 mm (key aggregate type a) at crusher., aggregates 13.2 mm to 5.6 mm at crusher., aggregates 13.2 mm to 10 mm at crusher., aggregates 20 mm to 10 mm at crusher., aggregates 25 mm to10 mm at crusher., aggregates 19 mm to 6 mm at crusher., aggregates 37.5 mm to 19 mm at crusher., aggregates 37.5 mm to 25 mm at crusher., aggregates 6 mm nominal size at crusher., aggregates 10 mm nominal size at crusher plant., aggregates 13.2/12.5 mm nominal size at crusher plant., aggregates 20 mm nominal size at crusher plant., aggregates 25 mm nominal size at crusher., aggregates 40 mm nominal size at crusher., crushing of stone aggregates (gsb crusher run), ac pipe 100 mm dia, acrylic polymer bonding coat, alluminium paint, aluminium alloy plate 2mm thick, aluminium alloy/galvanised steel , aluminium sheeting 2mm thick fixed with encapsulated lens type reflective sheeting including 2% towards lettering, cost of angle iron, cost of drilling holes, nuts, bolts etc.and signs as applicable class-b type iv, road aluminium stud with micro prismatic lens reflectors (with shank) 100 x 100 mm, barbed wire, bearing (cost of parts), bearing (cast steel rocker bearing assembly of 250 to

State Government

CTN :45562938

22 Jun, 2026 NA

Ranchi - Jharkhand

Tender For stone boulder of size 150 mm and below at source quarry supply of quarried stone 150-200 mm size for hand broken at source quarry boulder with minimum size of 300 mm for pitching at source quarry coarse sand i) at source coarse sand ii) at source fine sand at source quarry moorum at source quarry gravel/quarry spall at source quarry granular material or hard murum for gsb works at source quarry fly ash conforming to is:3812 (part ii & i) at hmp plant/batching plant/crushing plant filter media/filter material as per table 300-3 (mort&h specification) at crusher. close graded granular sub-base material 53 mm to 9.5 mm/4.75mm at crusher. close graded granular sub-base material 37.5 mm to 9.5 mm at crusher. close graded granular sub-base material 26.5 mm to 9.5 mm at crusher. close graded granular sub-base material 9.5 mm to 4.75 mm at crusher. close graded granular sub-base material 9.5 mm to 2.36mm at crusher. close graded granular sub-base material 4.75mm to 2.36mm at crusher. close graded granular sub-base material 4.75mm to 75 micron at crusher. close graded granular sub-base material 2.36 mm & below at crusher. stone crusher dust finer than 3 mm with not more than 10% passing 0.075 mm sieve at crusher. coarse graded granular sub-base material 2.36 mm & below at crusher. coarse graded granular sub-base material 4.75 mm to 75 micron at crusher. coarse graded granular sub-base material 4.75mm to 2.36 mm at crusher. coarse graded granular sub-base material 9.5mm to 4.75 mm at crusher. coarse graded granular sub-base material 26.5mm to 4.75 mm at crusher. coarse graded granular sub-base material 26.5 mm to 9.5 mm at crusher. coarse graded granular sub-base material 37.5 mm to 9.5 mm at crusher. coarse graded granular sub-base material 53 mm to 26.5 mm at crusher. aggregates below 5.6 mm at crusher. aggregates 22.4 mm to 2.36 mm at crusher. aggregates 22.4 mm to 5.6 mm at crusher. aggregates 45 mm to 2.8 mm at crusher. aggregates 45 mm to 22.4 mm at crusher. aggregates 53 mm to 2.8 mm at crusher. aggregates 53 mm to 22.4 mm(grade iii) at crusher. aggregates 63 mm to 2.8 mm at crusher. aggregates 63 mm to 45 mm (grade ii)at crusher. aggregates 90 mm to 45mm(grade i) at crusher. aggregates 10 mm to 5 mm at crusher. aggregates 11.2 mm to 0.09 mm (key aggregate type b) at crusher. aggregates 13.2 mm to 0.09 mm (key aggregate type a) at crusher. aggregates 13.2 mm to 5.6 mm at crusher. aggregates 13.2 mm to 10 mm at crusher. aggregates 20 mm to 10 mm at crusher. aggregates 25 mm to10 mm at crusher. aggregates 19 mm to 6 mm at crusher. aggregates 37.5 mm to 19 mm at crusher. aggregates 37.5 mm to 25 mm at crusher. aggregates 6 mm nominal size at crusher. aggregates 10 mm nominal size at crusher plant. aggregates 13.2/12.5 mm nominal size at crusher plant. aggregates 20 mm nominal size at crusher plant. aggregates 25 mm nominal size at crusher. aggregates 40 mm nominal size at crusher. crushing of stone aggregates (gsb crusher run) ac pipe 100 mm dia acrylic polymer bonding coat alluminium paint aluminium alloy plate 2mm thick aluminium alloy/galvanised steel aluminium sheeting 2mm thick fixed with encapsulated lens type reflective sheeting including 2% towards lettering, cost of angle iron, cost of drilling holes, nuts, bolts etc.and signs as applicable class-b type iv road aluminium stud with micro prismatic lens reflectors (with shank) 100 x 100 mm barbed wire bearing (cost of parts) bearing (cast steel rocker bearing assembly of 250 tonne ) road studs 100x100mm fitted with lense reflectors vide clause cl 804.2 of morth (5th revision) bearing (elastomeric bearing assembly consisting of 7 internal layers of elastomer bonded to 6 nos. internal reinforcing steel laminates by the process of vulcanisation) taking elastomeric bearing of size 500 x 400 x 96mm, overall volume=19200 cubic cm bearing (forged steel roller bearing of 250 tonne) bearing (pot type bearing assembly consisting of a metal piston supported by a disc, pt

State Government

CTN :45558189

22 Jun, 2026 NA

Chaibasa - Jharkhand

Tender For the quotation is invited to ascertain and assess the rate of materials as per with lowest market rate for framing of schedule of rate. - stone boulder of size 150 mm and below at source quarry, supply of quarried stone 150-200 mm size for hand broken at source quarry, boulder with minimum size of 300 mm for pitching at source quarry, coarse sand i) at source, coarse sand ii) at source, fine sand at source quarry, moorum at source quarry, gravel/quarry spall at source quarry, granular material or hard murum for gsb works at source quarry, fly ash conforming to is:3812 (part ii & i) at hmp plant/batching plant/crushing plant, filter media/filter material as per table 300-3 (mort&h specification) at crusher., close graded granular sub-base material 53 mm to 9.5 mm/4.75mm at crusher., close graded granular sub-base material 37.5 mm to 9.5 mm at crusher., close graded granular sub-base material 26.5 mm to 9.5 mm at crusher., close graded granular sub-base material 9.5 mm to 4.75 mm at crusher., close graded granular sub-base material 9.5 mm to 2.36mm at crusher., close graded granular sub-base material 4.75mm to 2.36mm at crusher., close graded granular sub-base material 4.75mm to 75 micron at crusher., close graded granular sub-base material 2.36 mm & below at crusher., stone crusher dust finer than 3 mm with not more than 10% passing 0.075 mm sieve at crusher., coarse graded granular sub-base material 2.36 mm & below at crusher., coarse graded granular sub-base material 4.75 mm to 75 micron at crusher., coarse graded granular sub-base material 4.75mm to 2.36 mm at crusher., coarse graded granular sub-base material 9.5mm to 4.75 mm at crusher., coarse graded granular sub-base material 26.5mm to 4.75 mm at crusher., coarse graded granular sub-base material 26.5 mm to 9.5 mm at crusher., coarse graded granular sub-base material 37.5 mm to 9.5 mm at crusher., coarse graded granular sub-base material 53 mm to 26.5 mm at crusher., aggregates below 5.6 mm at crusher., aggregates 22.4 mm to 2.36 mm at crusher., aggregates 22.4 mm to 5.6 mm at crusher., aggregates 45 mm to 2.8 mm at crusher., aggregates 45 mm to 22.4 mm at crusher., aggregates 53 mm to 2.8 mm at crusher., aggregates 53 mm to 22.4 mm(grade iii) at crusher., aggregates 63 mm to 2.8 mm at crusher., aggregates 63 mm to 45 mm (grade ii)at crusher., aggregates 90 mm to 45mm(grade i) at crusher., aggregates 10 mm to 5 mm at crusher., aggregates 11.2 mm to 0.09 mm (key aggregate type b) at crusher., aggregates 13.2 mm to 0.09 mm (key aggregate type a) at crusher., aggregates 13.2 mm to 5.6 mm at crusher., aggregates 13.2 mm to 10 mm at crusher., aggregates 20 mm to 10 mm at crusher., aggregates 25 mm to10 mm at crusher., aggregates 19 mm to 6 mm at crusher., aggregates 37.5 mm to 19 mm at crusher., aggregates 37.5 mm to 25 mm at crusher., aggregates 6 mm nominal size at crusher., aggregates 10 mm nominal size at crusher plant., aggregates 13.2/12.5 mm nominal size at crusher plant., aggregates 20 mm nominal size at crusher plant., aggregates 25 mm nominal size at crusher., aggregates 40 mm nominal size at crusher., crushing of stone aggregates (gsb crusher run), ac pipe 100 mm dia, acrylic polymer bonding coat, alluminium paint, aluminium alloy plate 2mm thick, aluminium alloy/galvanised steel, aluminium sheeting 2mm thick fixed with encapsulated lens type reflective sheeting including 2% towards lettering, cost of angle iron, cost of drilling holes, nuts, bolts etc.and signs as applicable class-b type iv, road aluminium stud with micro prismatic lens reflectors (with shank) 100 x 100 mm, barbed wire, bearing (cost of parts), bearing (cast steel rocker bearing assembly of 250 tonne ), road studs 100x100mm fitted with lense reflectors vide clause cl 804.2 of morth (5th revision), bearing (elastomeric bearing assembly consisting of 7 internal layers of elastomer bonded to 6 nos. internal reinforcing steel laminates by the process of vulcanisation), taking elastomeri

State Government

CTN :45562939

22 Jun, 2026 NA

Hazaribag - Jharkhand

Tender For list of approved construction materials for the preparation of schedule of rates for the year 2026, basic rates of which to be approved by the state level schedule rate committee (materials should conform to relevant b.i.s., mord and mort&h specifications). the rates will be inclusive of royalty but exclusive of all taxes, g.s.t,overhead and contractors profit. "rates are at source"quarry/ crusher plant. - stone boulder of size 150 mm and below at source quarry, supply of quarried stone 150-200 mm size for hand broken at source quarry, boulder with minimum size of 300 mm for pitching at source quarry, coarse sand i) at source, coarse sand ii) at source, fine sand at source quarry, moorum at source quarry, gravel/quarry spall at source quarry, granular material or hard murum for gsb works at source quarry, fly ash conforming to is:3812 (part ii & i) at hmp plant/batching plant/crushing plant, filter media/filter material as per table 300-3 (mort&h specification) at crusher., close graded granular sub-base material 53 mm to 9.5 mm/4.75mm at crusher., close graded granular sub-base material 37.5 mm to 9.5 mm at crusher., close graded granular sub-base material 26.5 mm to 9.5 mm at crusher., close graded granular sub-base material 9.5 mm to 4.75 mm at crusher., close graded granular sub-base material 9.5 mm to 2.36mm at crusher., close graded granular sub-base material 4.75mm to 2.36mm at crusher., close graded granular sub-base material 4.75mm to 75 micron at crusher., close graded granular sub-base material 2.36 mm & below at crusher., stone crusher dust finer than 3 mm with not more than 10% passing 0.075 mm sieve at crusher., coarse graded granular sub-base material 2.36 mm & below at crusher., coarse graded granular sub-base material 4.75 mm to 75 micron at crusher., coarse graded granular sub-base material 4.75mm to 2.36 mm at crusher., coarse graded granular sub-base material 9.5mm to 4.75 mm at crusher., coarse graded granular sub-base material 26.5mm to 4.75 mm at crusher., coarse graded granular sub-base material 26.5 mm to 9.5 mm at crusher., coarse graded granular sub-base material 37.5 mm to 9.5 mm at crusher., coarse graded granular sub-base material 53 mm to 26.5 mm at crusher., aggregates below 5.6 mm at crusher., aggregates 22.4 mm to 2.36 mm at crusher., aggregates 22.4 mm to 5.6 mm at crusher., aggregates 45 mm to 2.8 mm at crusher., aggregates 45 mm to 22.4 mm at crusher., aggregates 53 mm to 2.8 mm at crusher., aggregates 53 mm to 22.4 mm(grade iii) at crusher., aggregates 63 mm to 2.8 mm at crusher., aggregates 63 mm to 45 mm (grade ii)at crusher., aggregates 90 mm to 45mm(grade i) at crusher., aggregates 10 mm to 5 mm at crusher., aggregates 11.2 mm to 0.09 mm (key aggregate type b) at crusher., aggregates 13.2 mm to 0.09 mm (key aggregate type a) at crusher., aggregates 13.2 mm to 5.6 mm at crusher., aggregates 13.2 mm to 10 mm at crusher., aggregates 20 mm to 10 mm at crusher., aggregates 25 mm to10 mm at crusher., aggregates 19 mm to 6 mm at crusher., aggregates 37.5 mm to 19 mm at crusher., aggregates 37.5 mm to 25 mm at crusher., aggregates 6 mm nominal size at crusher., aggregates 10 mm nominal size at crusher plant., aggregates 13.2/12.5 mm nominal size at crusher plant., aggregates 20 mm nominal size at crusher plant., aggregates 25 mm nominal size at crusher., aggregates 40 mm nominal size at crusher., crushing of stone aggregates (gsb crusher run), ac pipe 100 mm dia, acrylic polymer bonding coat, alluminium paint, aluminium alloy plate 2mm thick, aluminium alloy/galvanised steel, aluminium sheeting 2mm thick fixed with encapsulated lens type reflective sheeting including 2% towards lettering, cost of angle iron, cost of drilling holes, nuts, bolts etc.and signs as applicable class-b type iv, road aluminium stud with micro prismatic lens reflectors (with shank) 100 x 100 mm, barbed wire, bearing (cost of parts), bearing (cast steel rocker bearing assembly of 250 tonne ), road st

Central Government/Public Sector

CTN :45384656

20 Jun, 2026 31.96 Lacs

Pune - Maharashtra

Tender For corrigendum : provision of additional transformer alongwith associated items at af stn pune under ge (af)lohegaon - s & f steel tubular swaged poles complete with cast iron plate, finial taper plug, bolt, nuts & screws as specified type 410 sp-55 (11 mtr long) including one coat of red oxide primer and two coats of aluminium paint and making 30 cm wide strips (total -05 nos) with yellow and black paint alternately on external surface above column/pcc benching including numbering with black paint and painting with bitumenous paint internally and externally for portion embedded complete all as specified and directed., s & f air break gang operated switch with 12 nos insulators outdoor type, triple pole, mechanically operated, suitable for vertical installation, single break, provided with locking arrangement consisting of ms chanel ht post type insulator copper alloy, high pressure assembly drop out fuses operating rod of 20 mm dia gi pipe (medium grade) for operating from 1.2 m above gl complete including drop out fuses conforming to is-9921 part-i to v (1982 to 1985) of 1972 rated voltage 11 kv and for current rating 200 amp all as specified, material and labour for lightning arresters nominal discharge current peak 65 ka rating, suitable for operation on ht 11000 volts system, comprising of zinc oxide disks, electrodes, fibre re-in forced composite structure, non tracking weather resistant shedded heat shrinked polymeric housing for withstanding from the effects of pollution, rain, heat and with moisture seal , stainless steel bolts and nuts, stainless steel end fitting cups and fixing arrangements complete all as specified and as directed., m&l for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections i.e m.s. channel or angle sections etc. including new nuts, bolts, washers as reqd dia/length in size, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive one primer coat of red oxide, one under coat and one finishing coat of aluminium paint (1st quality ) as reqd complete as specified., m & l for cement concrete 1:3:6 type c1 (using 20 mm graded aggregate) as lean concrete for coping of pole, stay foundation etc including form work & finishing the surfaces even & smooth with out using extra cement complete all as specified, material and labour for cement concrete 1:2:4, type b-2 (using 40 mm graded stone aggregate) as lean concrete for road finishing even and fair without using extra cement complete all as specified and as directed., supply, laying & testing cable xlpe insulated, screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 11000 volts grade, of size 3 core 95 sq mm., s&f of cable end jointing kit 95 sqmm, 3 core xlpe 11kv ht cable cold shrinkable outdoor type, incl carrying out 5kv megger test after jointing complete all as specified and directed by engr-in-charge., s&f of cable end jointing kit 95 sqmm, 3 core xlpe 11kv ht cable cold shrinkable indoor type, incl carrying out 5kv megger test after jointing ,complete all as specified and directed by engr-in-charge., supply, laying & testing cable xlpe insulated, screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of size 3.5 core 400 sq mm including aluminium lugs, cable glands ,complete all as specified and directed by engr-in-charge., supply, laying & testing industral pvc frls insulated single core flexible cable, electric power cables (heavy duty) with stranded copper conductor, 1100 volts grade, of size single core 185 sq mm, including copper cable lugs, cable glands ,complete all as specified and directed by engr-in-charge., supply and install, testing and commisioning of outdoor transformer as per is : 1180 part-i, level-ii step down, c

Drilling Hole Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors