Latest e waste scrap Tenders | Government e waste scrap Tenders

Central Government/Public Sector

CTN :45576091

20 Jun, 2026 NA

Mumbai - Maharashtra

Tender For supply installation wiring & testing of programming controller variable frequency drive panel with powder coating siemens grey-7035 for mh-60 hp, ct-5 hp, lt-10hp, ah-25hp double speed for all motion with joystick with rrc master controller pendent operating with eot crane brake light arrangement along with dbr panel, along with protection switchgear consisting mcb of 6 amp, 18ka, sp/dp control transformer of 500va, 0-440-415-410/0-110 vac, relay with base, 3-ph line choke, dbr-2.75e,27.5kw break contactor along with suitable cables, terminations, etc. confirming to is 13408 or latest, supply for 30 ton eot crane at lower parel workshop. accepted make: yaskawa siemens | schineder or equivalent. detailed bom is attached as per annexure a. [ warranty period: 30 months after the date of delivery ] ]

corporations/Associations/Others

CTN :45567699

24 Jun, 2026 NA

Dehradun - Uttarakhand

Tender For auction sale of old, used, waste, scrap old office paper items as per description

corporations/Associations/Others

CTN :45567702

24 Jun, 2026 NA

Dehradun - Uttarakhand

Tender For auction sale of old,used,waste, scrap miscellaneous electronic waste items, as per annexure

corporations/Associations/Others

CTN :45567697

23 Jun, 2026 NA

Ghaziabad - Uttar Pradesh

Tender For auction sale of old, used, & waste electronics (e-waste) scrap items, as per desc.

CTN :45543999

04 Jul, 2026 45.25 Lacs

Allahabad - Uttar Pradesh

Tender For supply of hdmi matrix switcher , desktop pc with 14700 processor 16 gb ddr5 , server pc with i9 processor , 4k vc camera with 20 optical zoom , chairman unit microphone , delegate unit microphone with frequency response 40 to 20000 hz , digital controller for chairman delegate unit with snr of 85 db or more , audio feedback suppression processor with afc and anc , dual microphone control system with freq response 40hz to 20000hz , look at me controller , digital signal processor with multi channel and inbuilt aec 8 port gpio interface , multi channel amplifier with 100v line 70v line , wireless microphone set with s n ratio of greater then 109db , wall mount speaker with 5 inch lf driver , 12u av equipment rack , 4mp full hd ir bullet camera with 1 to 7 inch 4mp ps cmos image senior , 16 channel nvr with 2sata hdd and ai recorder , 8 port poe 1 to 2 manged switch , surveillence hard disk 8tb , cat6 cable relies on the t568b or t568a , 4u walll mount rack , pvc box for camera mounting , ofc cable 6 core unarmored with uv stabilized black high density polyethylene , biometric access control system with magnetic lock and exit button , fire alarm system with heat and smoke alarm and manual call point , printer switcher with 2in 4 out , printer cable 10m , ups 20kva with 30 mint backup as either 3 phase with heavy duty ms steel rack , cable connector , programming and testing installation configuration and user training * /bid number : gem/2026/b/7627722 + /dated: 13-06-2026 ' ' / bid document 1 / 27

CTN :45541202

23 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For purchase of tanche - lab equipments for eee and ece department - purchase - lab equipments for eee department electronics lab, single phase to single phase cyclo converter kit single-phase bridge cycloconverter power devices: scr/triac based input supply: 230 v ac, 50 hz step-down isolation transformer 230 v / 12 v output: 12 15 v ac, frequency: 0 25 hz (adjustable),firing angle control circuit and frequency control circuit to be provided built-in resistive load, terminals to be brought on ms panel with necessary symbols and circuits, pwm based step down dc chopper using mosfet/igbt kitpwm based step-down dc chopper (buck converter) power device : power mosfet / igbt based switching circuit input supply : 24 v dc to 110 v dc or derived from 230 v ac mains through rectifier unit output voltage :(0 to vin) variable dc output current : up to 5 a dc maximum with suitable load resistor (r load) pwm duty cycle control provided pwm generation and control circuit inbuilt gate driver circuit provided, single phase single pulse / sinusoidal pwm inverter using mosfet/igbt kittype : single phase pwm inverter trainer power device : mosfet / igbt based inverter circuit input supply : 12 24 v dc output voltage : 30 v rms ac output phase : single phase output frequency : 0 50 hz variable output power : 100 w single pulse pwm operation sinusoidal pwm (spwm) operation variable frequency control pwm generation and firing control circuit inbuilt gate driver circuit provided test points provided for waveform observation and analysis built-in resistive load provision, on / off control of lamp using solid state relay kittype : solid state relay (ssr) trainer kit control/input voltage : 12 v / 24 v dc or up to 30 v dc output load voltage : 230 v ac, single phase load control : on/off control of ac lamp load solid state relay based switching circuit opto-isolated input control built-in ac lamp load manual on/off switching arrangement led indication for input and output status, speed control of ac motor using vfd drive module with ac motortype : variable frequency drive (vfd) module input supply : 415 v ac, three phase, 50 hz output : three phase variable voltage and variable frequency ac output 1 hpthree phase squirrel cage induction motor415 v ac 50 hz &1440 rpm control technique : pwm / spwm based control frequency range : 0 50 hz variable digital display for frequency and operating parameters start / stop and forward / reverse control, acceleration and deceleration control facility powder coated ms control panel tabletop / floor mounted laboratory type setup clearly labelled circuit diagram and control switches proper insulated terminals and earthing arrangement, purchase - lab equipments for eee department electrical machines lab, three phase transformertype: three phase transformer, rating: 3 kva input voltage: 415 v ac, 3-phase, output voltage: 230 v ac, 3-phase frequency: 50 hz winding material: copper wound insulation class: class b or higher duty: continuous duty suitable for laboratory usebench/floor, dc stepper motor drive kit with stepper motorinput supply : 230 v ac, 50 hz stepper motor : permanent magnet / hybrid type with suitable driver circuits. motor operating voltage : 12 24 v dc variable speed control forward and reverse direction control full step and half step operation manual / automatic pulse generation facility built-in regulated dc power supply led indication for phase sequence and status test points provided for waveform observation start / stop control switches to be provided overload and short circuit protection to be provided mounted on compact powder coated cabinet with printed circuit diagram proper insulated terminals and interconnecting leads to be provided patch chords for interconnection., dc servo motor drive kit with servo motorinput supply : 230 v ac, 50 hz servo motor type : dc servo motor with feedback arrangement motor operating voltage : 12 24 v dc controller type : microcontroller based servo drive contr

CTN :45354788

17 Jun, 2026 NA

Shekhapura - Bihar

Tender For bid to ras supply of arduino uno microcontroller , breadboard , jumper wires male female , resistors , led red green , capacitors , transistors , diodes , sensors , lcd , relay module , motors , power supply battery , multimeter , soldering kit , project work station , fpga trainer boards , logic analyzer , dual regulated power supply , arduino uno , stm dev board , pic development kit , raspberry pi , digital multimeter , dac trainer board , rtos trainer , soldering stations , lm analog temp sensor , ds digital temp sensor , ptrtd resistance temp detector , k type thermocouple , ir proximity sensor reflective ir , digital ir obstacle sensor , ir flame sensor , ir temperature sensor mlx90614 , mq two lpg smoke , mq three alcohol , mq six lpg butane , mq seven carbon monoxide , mq air quality , pir motion sensor , ultrasonic sensor , accelerometer , gyroscope , solderless breadboard full size , mini breadboard , jumper wires male male , jumper wires male female , jumper wires female female , ic socket eight pin , ic socket fourteen pin , ic socket sixteen pin , solar cell trainer kit , ujt as relaxation oscillator kit , scr characteristics kit , ldr , photo diode , phototransistor , semiconductor temperature coefficient trainer kit , logic gate trainer kit , ic trainer kit , measurement of steady state and transient response of rl rc and rlc circuits , frequency response of twin t notch filter and to study of active filter , study of single phase inverter trainer , to study the behaviour , determine the transient , to study of pid controller for simullatio n process , to study basic electric al trainer , to study single phase transformer , to obtain efficiency of a dc shunt machine , to obtain efficiency and voltage regulation of a single phase transform , to study dc series motor , make connection of dol starter , test the machines required , maxwells bridge trainer kit ) /bid number : gem/2026/b/7582907 * /dated: 27-05-2026 & & / bid document 1 / 44

CTN :45525479

06 Jul, 2026 11.85 Lacs

Kamrup - Assam

Tender For establishment of material testing laboratory under o/o the agm(c) design and projects aegcl kahilipara - civil works, compression testing machine (2000kn) with digital reading, automatic pace control with all attachment for testing concrete cube & bricks conforming to indian standards (is: 516, is: 14858) and can also be supplied as per british standards (bs: 1881), astm c-39 with calibration certificate. it should be typically calibrated to class 1 accuracy ( 1%); featuring a robust, fully welded loading unit and hardened, ground, and polished platens, often with a self-aligning upper platen; with display type as pc-controlled with software. it should have pace rate of full three-term pid feedback control with fully automated data acquisition, storage, and analysis. the operation should be fully automated, stress & strain controlled loading., aggregate impact test, crushing value apparatus with hammer weight of 13.75 kg 0.25 kg (or 14 kg 0.5 kg), height of free fall of 380 mm 5 mm, impact cup (mould) inner diameter of 102 mm 0.25 mm and impact cup depth of 50 mm 0.25 mm as per is 2386 (part iv), bs 812-112. automation grade often semi-automatic with a digital counter. display type digital for the blow counter; sometimes includes a digital gauge for other measurements. overall weight (approx.) should be of 45 kg to 60 kg (total machine mass). standards compliance conforms to international standards like is: 2386 (part iv), bs 812-112, etc. , sieves: (40, 20, 10, 4.75, 2.36, 1. 18) mm with lid and pan and (0.6, 0.3, 0. 15, 0.075) with lid and pan (all 200mm diameter size) metal : gi, weighing balance-30kg (accuracy-1gm)., weighing balance-5kg (accuracy-0.1gm)., hot air oven with double walled design, thick glass wool insulation to prevent heat loss, micro processor based auto tune pid digital temp controller cum indicators and 230 volt 50hz single phase ac supply, heavy duty stainless steel lock, indoor hinge and sample placement trays, temp range should be 50 degree c 250 degree c with temp accuracy 0.5 degree c. it should have digital led display of size 45 cm x 45 cm x 45 cm (inner)., cube mould (cast iron) of size 150mmx150mmx150mm, isi marked as per is:10086. weight of the mould will be about 13.5 kg, strictly as per bis specifications and within required tolerance., slump cone test apparatus-(isi marked)-with tamping rod (complete set ) as per is: 7320 and is: 1199 part 2, consisting of slump cone, base plate and graduated tamping rod - made of stainless steel., proctor test apparatus with all accessories as per is: 2720 part 8 and is: 10074(1982), complete with base plate and collar., measuring cylinder-borosilicate (1 complete set ) glass of sizes 100 ml, 250 ml, 500 ml and 1000 ml., field density test app-core cutter method ( complete set) complete with core cutter of 100 mm dia x 130 mm long with chromium plating, dolly for 100 mm dia core cutter, and rammer with steel rod as per is : 2720, rebound hammer digital (original/silver schmidt type n) with calibration certificate as per is 516 part 5, sec 4 with impact energy of 2.207 nm (1.63 ft-lbf), concrete strength range of 10 100 mpa (1450 14500 psi) and weight of 570 g (1.3 lb) with display as graphic lcd (e.g., 17x71 pixels) or analog/digital and battery life: >5000 impacts., ultrasonic pulse velocity test apparatus (proceq, acoustic control systems, vedantrik technologies) with calibration certificate and frequency range of 24 500 khz (nominal transducer); measurement resolution of 0.1 s (microseconds); pulse voltage ranging from 125 v to 500 v (adjustable); receiver gain of 1x, 10x, 100x, auto, up to 1000x (lab+ model); pulse shape as square wave; measurement modes as pulse velocity, surface velocity, e-modulus, compressive strength correlation, crack depth; memory which stores >500 measured values; display should be 79x21 mm passive matrix oled; connectivity through usb for pc connection; software: pundit link for analysis and export. standards compliance

CTN :45563588

10 Jul, 2026 NA

Multi City - Delhi

Tender For corrigendum : auction sale of e-waste - scrap of hardware, peripheral & furniture items

CTN :45550361

22 Jun, 2026 NA

Multi City - Uttar Pradesh

Tender For auction sale of depot non ferrous scrap - copper cable scrap consists of various types of mixed waste scrap comprising of pvc insulated armoured copper cables, in different cores, sorts of sizes, with steel armoured. this scrap includes a varity of other known or unknown armoured copper cable or wire, unfit for railway use, lying in godown no. 16 [gst-18%, hsn code-740400] [moef condition will be applicable]

E Waste Scrap Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

corporations/Associations/Others

corporations/Associations/Others

corporations/Associations/Others