Get complete information related to latest Earth Terminal Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Earth Terminal Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Earth Terminal Tenders.
Tender For supply of primary earthing terminal p- 4 bushing of transformer for emus. specn: kpadrg. no. er/kpa/el/tf.2he.486 f. [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]
Tender For : supply, installation, testing & commissioning of electrical equipment for dg block 119a of inrp - ht panels (119a)supply, installation, testing & commissioning of indoor type floor mounted, single front, metal clad, 1250 a, 6.6 kv, 3 phase, 3 wire, vcb switchgear panel suitable for a short circuit current of 31.5 ka for 3 seconds, internally arc tested for 31.5 ka for 1 second, comprising of following incoming & outgoing feeders : incoming feeder: 1 no. 1250 a, 3p vcb outgoing feeders: i) 7 nos. 630 a, 3p vcbii) 1 no. 1250 a, 3p vcb as tie feederwith surge arrestors, relays, pts, cts & other necessary accessories including associated structural steel required for complete installation of the panel & equipment earthing of the panel from both the earthing terminals of the panel to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings. reference drg. nos: ip1/119a/05027339/dwg/001/r0 & ip1/119a/05027339/dwg/002/r0(note: terminal box of each incomer of 6.6kv switchboard shall be suitable for terminating 4x3cx400 sq.mm., 6.35/11kv (e), a2xwy cables.), supply of spares for ht panels as per attached spares list mentiond in section c, part ii of tender, 2.5 mva, 6.6/0.433 kv dry type transformers (119a)supply, installation, testing & commissioning of 6.6/0.433 kv, 2.5 mva, dyn11 dry type cast resin transformer having percentage impedance of 8.5% complete with ht cable end box, lt bus duct flange, off load tap changer on ht side with range of +/-5% in steps of 2.5%, wti scanner, ct for restricted earth fault protection and other necessary accessories including associated structural steel required for complete installation of the transformer & equipment & neutral earthing of the transformer from both the earthing terminals of the transformer to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings.reference drg. no. : ip1/119a/05034347/dwg/001/r0, supply of spares for dry type transformers as per attached spares list mentiond in section c, part ii of tender, 2000 kva diesel generator sets (119a)supply, installation, testing & commissioning of 3 phase 2000 kva prime power 433v, 50hz, 0.8 p.f. diesel-generator sets with 110% overload capacity for 1 hr with four (4) stroke inline or vee type cylinder arrangement having engine speed 1500 rpm, 24v electric battery starting system with a provision of interchangeability of battery bank between two dg sets, complete with all auxiliary equipment including amf control panel, auxiliary mcc panels, heat exchanger cooling system, raw water pump, remote radiator with fans on terrace, ms exhaust piping, exhaust structure (maximum 30 m stack), 4 nos. of 3.6 cubic metre fuel day tank outside dg building (for all 4 dg sets) & 1 no. of 990 ltr intermittent tank inside each dg room, ms "c" class fuel piping between engine & fuel tank, dg room accoustic treatment & complete ventilation of dg room, brushless excitation for alternator, one no. 3200 amp 415 v 4p acb, ms structural steel supports/ channels/ angles & other necessary accessories including associated structural steel required for complete installation of the dg & equipment & neutral earthing of the dg from both the earthing terminals of the dg to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & necessary statutory clearances from cpcb etc. as required and as per tender technical specifications & drawings. design and construction of foundation for exhaust pipe rack/ structure of dg set is included in the scope of the contractor.reference drg. nos. : i) ip1/119a/05034347/dwg/001/r0ii) ip1/119a/05044831/dwg/003/r0iii) ip1/119a/05044831/dwg/004/r0iv) ip1/119a/05044831/dwg/005/r0v) ip1/119a/05044831/dwg/006/r0, supply of spares for diese
Tender For supply of primary earthing terminal p- 4 bushing of transformer for emus. specn: kpa drg. no. er/kpa/el/tf.2he.486 f. [ warranty period: 30 months after the date of delivery ]
Tender For supply of high mast light and misc items d d - providing and fixing of 16 meters high mast lighting tower for large area with 08 led flood light luminaires , providing and fixing of 10 meters high mast lighting tower for large area with 12 led flood light luminaires , led bulb 9w , copper chemical earthing with complete wire and materials , rubber adhesive providing and fixing of 16 meters high mast lighting tower for large area with 08 led flood light luminaires,octagonal pole construction with metal protection treatment of fabricated mast section, hot dip galvanised as per is:4759 latest, octagonal pole sheet thickness 3 mm, material of octagonal pole high tensile steel, 01 nos of longitudinal welds, type of welding is submerged arc welding process, internal distance between parallel faces at the base of pole 175, 01 no of section,internal distance between parallel faces at the top of pole 70, grades of high tensile steel ish430la as per is:5986 (grade 355), cross section of octagonal pole (no of sides) octagonal, with no door opening, width of base plate 300 mm, number of nuts for each pole 1, foundation bolt type j type en 8 grade, bolts and nuts are conforming to specication as per is:1363 - grade a, base plate material mild steel fe 410 conforming to is : 2062, necessary accessories on each pole foundation bolts,nuts, washers, instruction manuals, bolt size m24x750, thickness of base plate 16 mm, number of washer per bolt for each pole 2, number of bolts for each pole 4, foundation bolts and nuts and octagonal pole shall be galvanized as per is:4759 (latest), length of base plate 300 mm, earthing terminals on the base of the pole, for lightning and electrical protection, regional wind withstand capacity which the pole structure support is suitable to withstand (in m/s) 47, the designed life of the pole shall be 25 years, terminal box ) /bid number : gem/2026/b/7398300 * /dated: 01-04-2026 & & / bid document 1 / 15