Tender For repair/replacement of external electric supply distribution network with other connected items at malad, marve and kandivali under ge (n) santacruz, mumbai - supply, install, testing & commissioning pedestal cubical type double door lt bus bar chamber box of suitable size factory made modular construction fabricated out of 3 mm thick crca sheet, angle iron, channels, epoxy powder coated to give a superior finish , outdoor type , totally enclosed dust & vermin proof with locking arrangements front & back side opening system including rain shed, busbar chamber should be suitable for accomodating all aluminium bus bar strips (50mm x 10mm x 04 nos) & gi strip for earth fixed on porcelain insulators, and one independent metering module suitable for accomodating three phase volt meters & ammeter digital type, indicator lamps, cable entry/exits cut outs at bottom part, with fixing arrangement on pcc (1:3:6) type c-2 bed block with studs, bolts, nuts & washers, danger notice board with scull suitable for 415 volts or required size to be fixed on pannel including dismantling of old bus bar panel all as specified and directed by engr-in charge.notes:-(a) aluminium bus bar duly covered with colour coded shrinkable sleeves of required size for phases and neutral - 01 set(b) mccb 4 pole , ics=100%icu- 25 ka, 415 volts, 100 amps , with thermal adjustable and fixed magnetic setting with extended terminals -02 nos.(c) digital multifunction meter of size 96x96 mm to measure current, voltage, frequency and power factor with built in selector switch and programable ct of appropriate ratio.-01 no make- imp/automatic electrical(ae)/ l&t / havells/ meco(d) panel indicating lamp neon/led type (red ,yellow & blue) with lamp holders - 03 nos(e) panel instrumental wiring with frls suitable size but not less than 2.5 sqmm copper wire single core - 01 job(f) necessary sizes of lugs for fixing of cables in bus bar deemded to be included rate quoted by the contractor.make of mccb & mcb: larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 400 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:- larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 160 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 16 ka 100 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 250 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb all as specified and directed by engr-in-charge make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supplying, laying,connecting, testing & commissioning lt ug pvc insulated, heavy duty, 1100 v grade electric cable with aluminium conductor of size 16 sqmm x 4 core, laid in trenches or passing through pipe or fixed to wall, making all connections with and including provision of necessary glands, lugs, bushing etc as required including taking down old unserviceable cable complete all as specified and as directed by engineer-in-charge of following sizes:-note : earthwork excavation, dwc
Tender For supply of repair station for nsc rdr , electrostatic mat , shielded metal arc welding electrode , mild steel filler road 4mm x 450mm , ferrous metal repair electrode , flexible power transmission cable , flood light , copper conductor pvc insulated cable , modular power distribution panel
Tender For corrigendum : provision of noise reduction paneling for motivation hall, operation room and 05 in nos air conditioner for admin offices and special repair of main distribution panel associated with power distribution at icgs mayabunder, under ge(s) diglipur.
Tender For corrigendum : supply of providing and laying of painting works , patch works , waterproofing works , dismantling false ceiling , dismantling bison board , dismantling woden partistion , window closing , dismantling existing washbasin , cleaning , room 3 , providing toilets , toilet renovation works , roofing and false celing works , room 9 , floor patch works , dismantling of toilets , dismantling damaged windows , room 14 15 , dismantling existing doors , repairs to existing ventilator windows , dismantling existing wall and floor tiles , structural repair and opening modification works , dismantling brick structure and floor repair , dismantling and vegetation removal , dismantling existing broken and damaged glass panes , cpvc water supply line , site clearance and general demolition works , anti termite treatment , rodent and pest control treatment , overhead water tank cleaning repair and disinfection , storm water drain and surface drainage , signage and room identification , comprehensive checking of 1 nos 250 kva outdoor type substations including inspection , aluminium paint , servicing of existing 11 kv 400 amps 3 pole gang operated type air break ab switch , supplying and replacing damaged or worn out copper metal , supplying and replacing damaged or defective 11 kv post top insulators , supplying and replacing damaged or defective 11 kv pin type insulators , servicing of earth pits , supply installation testing and commissioning lbs , xlpe insulated aluminium conductor armoured ht cable , providing indoor or outdoor type heat shrinkable , supplying and laying of 3.5 core x 240 sq.mm 1.1 kv grade aluminium conductor xlpe insulated , supplying and making end termination for 3.5 core x 240 sq.mm 1.1 kv grade , joint for existing single run lt power cable of size 3.5 core x 240 sq.mm , comprehensive servicing and preventive maintenance of existing ht transformer , supply, fixing, installation, testing and commissioning of lightning arrester , providing and fixing cable identification tags , supply, installation, testing and commissioning sitc main mv panel , supply, installation, testing and commissioning sitc cubicle pdb panel , supply, installation, testing and commissioning sitc feeder pillar box , providing and installation of maintenance free earthing station , supplying and laying of 3.5 core x 120 sq.mm 1.1 kv grade aluminium conductor xlpe insulated , providing laying and fixing of overhead perforated or slotted ms cable tray , supply installation testing and commissioning 7 segment distribution board , providing fabricating supplying, installing testing and commissioning of electrical socket box
Tender For annual maintenance contract of installed e&m equipments in central drug standard control organization, gothapatna, bhubaneswar for financial year 2026-27. - & minor repairs of cctv & including, & minor repairs of kone lift i/c, (standard deviation colour matching), (standard deviation colour matching), (t.c.). manufactures word mark/, (unified glare rating) < 19, flicker, / 6500°k (as per ansi bin), sdcm, /6500°k (as per ansi bin),sdcm, <3,, <5, maximum power consumption, >85%, input voltage: 140-270 volt ac,, >85%, operating voltage ac 140-270, >85%, operating voltage ac 140-270, >85%,thd < 10% as per iec 61000-, 1 2,22,718.00 job 2,22,718.00 mr, 1 no 13 passenger lift,, 1.5 sq. mm frls/hffr, pvc, 10% , p. f.≥0.95, ip20, cri ≥80, ugr, 10.1 18 watt 10 618.00 each 6,180.00 mr, 10322 with driver as per the, 11.1 36 watt 10 2,103.00 each 21,030.00 mr, 12 13,877.00 month 1,66,524.00 mr, 12 16,961.00 month 2,03,532.00 mr, 12 21,586.00 month 2,59,032.00 mr, 12 24,086.00 month 289032 mr, 12 24,128.00 month 2,89,536.00 mr, 12 31,890.00 month 382680 mr, 12 4,490.00 month 53,880.00 mr, 12 53,452.00 month 6,41,424.00 mr, 125 kva dg set with amf and, 15u rack 1 13,330.00 nos 13,330.00, 2 x 6 sockets 16a power distribution, 2.5 kv with short & open circuit, 3-2, p. f.≥0.95, ip-66,ik-10, cri >70,, 39.23.3, 4000°k/ 5700°k /6500°k (as per ansi, 61000-4-5, driver efficiency, 70% of initial lumen maintained till life, 70% of initial lumen maintained till life, 90°c)., 90°c)., above 90°c)., aluminium body including trim, aluminium body with driver as per the, and earthing etc. as required with, annual comprehensive maintenance, annual comprehensive, maintenance, annual comprehensive, maintenance, approved by engineer-in-charge as, approved by engineer-in-charge as, approved by engineer-in-charge as, as required, as required., at gothapatna as required, attached & following staff., basis as per terms & conditions, basis) including servicing, preventive, bin), sdcm (standard deviation, bis standard complete in all respect, bis standards and trade mark, body material with pmma and, cable and earthing etc. as required, cable and earthing etc. as required, cables, nvr, switch, cctv camera,, cct 3000°k / 4000°k / 5700°k, cdtl building etc. as reqd., centigrade, internal surge protection of, certificate (t.c.). manufactures word, circuitry) of minimum 50000 burning, colour matching) <3,, commissiong of pa, rectification and, comprehensive and repair, comprehensive and repair, comprehensive and repair, condition at cdtl office building etc, contract (as inspection on monthly, copper conductor single core cable, day electrical complaints, complaint, distribution pane, 250 kva substation,, down lighter (round/ square/, driver & electrical circuitry), of, dsr-25, efficacy ≥105 <120 lm/watt) supplying, ends , cct 3000°k / 4000°k / 5700°k, ends as per lm80 extrapolation ies, entire lift , etc in cdtl office building, etc in cdtl office at gothapatna as, extrapolation ies tm-21-11 report,, fixture shall be confirming to relevant, fixture shall be of relevant bis, fixtures as per bis shall be submitted., fixtures as per bis shall be submitted., fixtures as per bis shall be submitted., free, (flicker should be below 5 %), life, frequency 50/60 hz, operating temp, general shift) at cdsco on monthly, hours with70% of initial lumen, housing such that led, housing such that led junction, housing such that led junction, i/c external connections with 1.5, in all respect i/c external connections, inspection on monthly basis) including, inspection on monthly basis) including, insulated copper conductor single core, insulated copper conductor single core, internal surge protection of 2.5 kv with, ip surveillance systems i/c maintance, ip20, cri ≥80 , ugr (unified glare, junctiontemperature shall not rise, knocked-down condition (ckd) shape,, led panel light 2x2 ft. (system lumen, lenses for beam angle asper iesna, life time (led, driver &
Tender For corrigendum : supply of supply part for retrofitting of lt panel by supply and installation , service part for retrofitting of lt panel by supply and installation , supply of main incoming lt power distribution panels slipway , install, replace, test and commissioning of main incoming lt power distribution panels slipway , supply of welding and lighting panels slipway , install, replace, test and commissioning of welding and lighting panels slipway , supply of 3.5c x 400 sq.mm aluminum cable from substation-02 to slipway , laying, fixing, testing and commissioning of 3.5c x 400 sq.mm aluminum cable from substation-02 to slipway , supply of 3.5cx 185 sq.mm aluminum cable from slipway-2 and 3 main incoming panels to welding and lighting panels , laying, fixing, testing and commissioning of 3.5cx 185 sq.mm aluminum cable from slipway-2 and 3 main incoming panels to welding and lighting panels , supply and fitment of suitable end termination kits - straight through joints kits of required quantity to all the incoming and outgoing cables at both ends of slipway-02, slipway-03, substations, etc , providing earth pits with 75mm ci pipe as is standards , supply and laying of gi flat 50 x10 mm necessary joints with nut and bolts from earth pit to panel boards , repair and excavation of cable trench of 75mm thick up to 90cm depth , fixing of perforated cable tray on slipways 02 and 03 and securing of cables with metal ties and capping and casing to be provided , foundation for all lt panels i.e. steel foundations with concrete pedestal for panels all incoming and welding and lighting panels
Tender For supply of supply part for retrofitting of lt panel by supply and installation , service part for retrofitting of lt panel by supply and installation , supply of main incoming lt power distribution panels slipway , install, replace, test and commissioning of main incoming lt power distribution panels slipway , supply of welding and lighting panels slipway , install, replace, test and commissioning of welding and lighting panels slipway , supply of 3.5c x 400 sq.mm aluminum cable from substation-02 to slipway , laying, fixing, testing and commissioning of 3.5c x 400 sq.mm aluminum cable from substation-02 to slipway , supply of 3.5cx 185 sq.mm aluminum cable from slipway-2 and 3 main incoming panels to welding and lighting panels , laying, fixing, testing and commissioning of 3.5cx 185 sq.mm aluminum cable from slipway-2 and 3 main incoming panels to welding and lighting panels , supply and fitment of suitable end termination kits - straight through joints kits of required quantity to all the incoming and outgoing cables at both ends of slipway-02, slipway-03, substations, etc , providing earth pits with 75mm ci pipe as is standards , supply and laying of gi flat 50 x10 mm necessary joints with nut and bolts from earth pit to panel boards , repair and excavation of cable trench of 75mm thick up to 90cm depth , fixing of perforated cable tray on slipways 02 and 03 and securing of cables with metal ties and capping and casing to be provided , foundation for all lt panels i.e. steel foundations with concrete pedestal for panels all incoming and welding and lighting panels
Tender For corrigendum : repair and maintenance of lt switch gear, distribution panel, bus bar, lt power cable and allied electrical work at technical area under ge (af) ambala
Tender For supply of fpga based full duplex sdr with 2x2 mimo , phase- coherent multi-channel full duplex sdr , reprogrammable fpga based dual channel mimo , low cost half duplex wide band sdr , low cost usb based sdr receiver , high performance 30 tops or more edge computing single board gpu based computer , hf band dipole antenna , antenna for complete l, s and c band , multi band v uhf shf omni directional antenna , sectoral antenna , antenna accessories , gnss band signal validation device foldable multi band with endurance of min 30 min or above, gps, gallilio and beidou gnss support , outdoor radio unit payload integrated with sectoral antenna , directional parabolic dish antenna with radio unit for uav payload mounting , outdoor cpe with 23 dpi dish antenna with integrated radio unit for uav payload mounting , wireless high throughput radio unit for communication between ground and aerial platform , integrated multifunction surveillance system payload with flight controller autopilot unit , advanced heavylift electronic speed controller propulsion system , 22.2v 25c 6s 22000mah lipo battery , 12s 30ah solid state battery , integrated ground control and telemetry system , smart bty charger bty mgt system , power monitoring distribution regulation module , lightweight rugged uav based platform using first person view support , analog based aerial platform to ground video data transmission vtx unit , multi band gnss receiver module m10 , power supply module 6s 10000mah li-ion battery , ground control station development frame for ofc based spooler platform with ground controller radio and accessories , heavy payload carrying 13-inch frame supporting fpv , constant dc power supply unit with 8s 15000mah rating and bty eliminator circuit board , ground control station development frame for heavy payload carrying aerial platform and accessories , multi-port battery charging unit 12s with indicator , integrated testing and repair kit with professional tool set , multi band portable antenna integrated with multiband signal generator , integrated development environment software of matlab tool , arc gis sdk software tool , java runtime environment sdk , server station , high performance desktop computer with hybrid compute core architecture , desktop pc with high performance multi core processor with stacked v-cache , network attached storage , led screen based interactive flat video wall , single soundbar system , separate chemical earthing fitment below 1 ohm , networked monochrome mfd with scanner , switching unit for display with 4 input and 4 output port , manageable layer 3 switch 16 port , manageable layer 2 switch 24 port , rgb supported printing device with inkjet head , dg sets silent gen 30 kva , online ups 5 kva , online ups 30 kva , environment control system air conditioner split , testing tools and soldering iron kit , networking cable management unit , testing tool box , hdmi male cable 15 mtr or above , laser pointer , digital earth resistance tester , digital clamp meter , digital multimeter , presenter device , utp cable cat 6e ethernet cable , patch panel 24 port , rj 45 connector , rosette box rj 45 , rj 45 coupler , crimping tool , installation and commissioning fpga based full duplex sdr with 2x2 mimo, phase- coherent multi-channel full duplex sdr, reprogrammable fpga based dual channel mimo //bid details 2 / 51
Tender For auction sale of cables cut pieces scrap copper strands,scrap others disposal of used oil from equipment,disposal of alpg scrap refer attachment,old canopy false ceiling sheets scrap,disposal of old rvi scrap,disposal of old ug tanks,old electricalpanels scrap