Latest foundation plate Tenders | Government foundation plate Tenders

CTN :45304567

08 Jun, 2026 4.60 Lacs

Thiruvananthapuram - Kerala

Tender For one panchayath one playground - development of vankulathuvayal stadium in azhikode grama panchayath in azhikode lac, kannur -supply and installation of outdoor gym equipment - supply and installation of horse rider having the following specifications: dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - 114 mm od b class gi pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. foundation cover cap - dome shape of pp / nylon / hdpe material. remaining frame is made by 48 mm od b class gi pipe. seat frame is made by 48 mm od b class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of 48 mm od b class g.i. pipe. angle between link and ground position is 10-20 degree. handle - 33 mm od b class gi pipe. paddle vertical support - 60 mm od b class gi pipe. handle frame- 42 mm od b class gi pipe dually bending design. foot pipe - 33 mm od b class gi pipe. support frame 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe. bearing bush closing cap pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand. bearing bushes - 60mm od seamless pipe. pin made of 25 mm m.s. bright bar. grips - high quality rubber 46 mm od. circlips a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start &finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od405586/2025-2026 leg press (double) - specifications: dimensions: (l x w x h) = 1676 x 400 x1500 mm. main frame - 114 mm od ?b? class gi pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. foundations cover cap - dome shape of pp / nylon / hdpe material. link - is 60 mm od b? class gi pipe. seat frame - 42 mm od b class gi pipe. leg press back rest should be angled in 120 -130 degree. footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 2 mm thick use to support it. seat & back rest ? 380 x 275 x 60 mm thick high-density polyethylene (hdpe) blow molded with m10 integrated wall thickness 3 to 4 mm. link connected with frame by 8 mm thick laser cutting ms profile. top closing cap ? dome shape made by pp / nylon / hdpe material. closing cap?s- pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing- use is 6005 permanent lubricated reputed brand. pin 25 mm m.s. bright bar pin. bearing bushes - 60 mm od seamless pipe. circlip? a 24 circlips are used for assembly. coating - best quality of powder coating 80 -120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od405583/2025-2026 back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from 88 mm od b class g.i. pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. leg support - 42 mm od b g.i pipe. seat rest pipe 42 mm od b class g.i pipe. handl

corporations/Associations/Others

CTN :45277495

28 May, 2026 4.67 Lacs

Chandigarh - Chandigarh

Tender For providing and fixing of open air gym equipments in various parks of sector 20,chandigaarh under ward development fund. - providing and fixing of chest press double size / dimensions length -1200 milimeterwidth- 700 milimeterheight 1800 milimetermaximum weight -120 kilogrammaterial:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength, durability, and corrosion resistance. the main central pipe shall be an 80 mm nb gi pipe, while the handle frame and sheet frame shall each consist of 40 mm nb gi pipes. the connecting links shall be made of 32 mm nb gi pipes, and the footrest pipe shall also be 32 mm nb gi. the mild steel (ms) foundation plate shall have a minimum thickness of 12 mm. the foundation pipe shall consist of a gi pipe anchored 750 mm deep and supported with an ms angle of 25 25 4 mm for stability. the seat and backrest shall be made of high-density polyethylene (hdpe) sheets with a thickness of 3 mm, designed with a uniform bending radius to avoid sharp edges and ensure user safety. all nuts and bolts used for assembly shall be made of galvanized iron (gi) to enhance durability and resistance to corrosion. the movement mechanism shall be fitted with ball bearings that are self-lubricating and sealed to protect against rain, dust, and other environmental elements. the closing caps of open ends of all pipes, as well as bearings, bushes, and bases, shall be covered with fibre-reinforced plastic (frp) closing caps having a minimum thickness of 3 mm. all plastic components shall be uv-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.colour:- green paint finish- power coated, uv resistantpaint coating thickness (min) 100 micrometerwarranty 3 years.complete in all respects, including installation of equipment in a cement concrete block of size 5 x 5 x 1 , to the entire satisfaction of the engineer-in-charge., providing and fixing of leg press leg shaper complete in all respects having following specifications.a) all pipes should used in the equipments should be galvanised with 3mm thickness.b) multi colour powder coating with polyster paints should be used on all the equipments.c) the foot pedal on all the equipments should be of aluminium only.d) the seats should be made of high quality plastic with colour scheme in yellow or orange.e) the high end bearings such as skf/nbc must be used in all the equipments.1 dimensions- 1730*450*1450mm2 colour- customizable multi colour and complete powder coat3 size of main tube-114*3.75mm steel pipe4 size of supporting tube-76*3mm steel pipe5 there is restrainer inside, the distance between swing arm and main tube is greater than 230mm avoiding the danger of getting stuck.6 al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 anti-skid components are used at the pedal parts.8 the distance between two spinners is no less than 230mm, avoiding the damage of being stuck9 anti theft cover is made by stainless steel/high quality plastic.10 thickness of bearing bracket is no less than8mm11 hazardous materials like coating agent, rubber are under national newest standard.functions: develops the strength of lower limbs, and improves the stability and agility of three main joints of lower limbs; good for the healing of inconvenience of bending and stretching of lower limbs, and muscular atrophy of lower limbs, rheumatoid arthritis, sciatica, sprain of the anklebone, etc. approaches: sit on the chair and step on the footboard. stretching legs with force and recover slowly. repeat. users: suitable for people of different ages.complete in all respects, including installation of equipment in a cement concrete block of size 5 x 5 x 1 , to the entire satisfaction of the engineer-in-charge., providing and fixing of parallel bars size/dimensionslength- 900 millimeterheight 800 millimetermaterial:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength and durability. the ver

CTN :45235943

26 May, 2026 1.03 Crore

Usmanabad - Maharashtra

Tender For design, fabrication, supply, erection, testing and commissioning double girder eot crane of 50 10 mt of pump houseincluding foundation plate anchorages, transportation, loading, unloading, levis, taxes etc. all complete job for krishna marathwada

corporations/Associations/Others

CTN :45236853

25 May, 2026 2.65 Lacs

Chandigarh - Chandigarh

Tender For providing and fixing of open air gym equipments in leisure valley, sector 10 a, ward no. 2, chandigarh under mplads. ln/mp18047/2024-2025/116. - providing and fixing of chest press double complete in all respects having following specifications. size / dimensions length -1200 milimeter width- 700 milimeterheight 1800 milimeter maximum weight -120 kilogram material:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength, durability, and corrosion resistance. the main central pipe shall be an 80 mm nb gi pipe, while the handle frame and sheet frame shall each consist of 40 mm nb gi pipes. the connecting links shall be made of 32 mm nb gi pipes, and the footrest pipe shall also be 32 mm nb gi. the mild steel (ms) foundation plate shall have a minimum thickness of 12 mm. the foundation pipe shall consist of a gi pipe anchored 750 mm deep and supported with an ms angle of 25 25 4 mm for stability. the seat and backrest shall be made of high-density polyethylene (hdpe) sheets with a thickness of 3 mm, designed with a uniform bending radius to avoid sharp edges and ensure user safety. all nuts and bolts used for assembly shall be made of galvanized iron (gi) to enhance durability and resistance to corrosion. the movement mechanism shall be fitted with ball bearings that are self-lubricating and sealed to protect against rain, dust, and other environmental elements. the closing caps of open ends of all pipes, as well as bearings, bushes, and bases, shall be covered with fibre-reinforced plastic (frp) closing caps having a minimum thickness of 3 mm. all plastic components shall be uv-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.colour:- green paint finish- power coated, uv resistantpaint coating thickness (min) 100 micrometer warranty - 3 years.complete in all respects, including installation of equipment in a cement concrete block of size 5 x 5 x 1 , to the entire satisfaction of the engineer-in-charge., providing and fixing of parallel bars complete in all respects having following specifications.size/dimensions length- 900 millimeter height 800 millimeter material:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength and durability. the vertical or standing pipes shall be 40 mm nb with a thickness of 2.9 mm, and the horizontal pipes shall also be 40 mm nb with a thickness of 2.9 mm. the foundation pipe shall consist of a gi pipe anchored 500 mm deep and supported with a mild steel (ms) angle of 25 25 4 mm. the nominal bore of the foundation pipe shall be 40 mm nb with a thickness of 2.9 mm. the ms foundation plate shall have a minimum thickness of 12 mm. all nuts and bolts used for assembly shall be made of stainless steel to provide durability and resistance to corrosion. the open ends of all pipes, bearing bushes, and bases shall be fitted with fibre-reinforced plastic (frp) caps having a minimum thickness of 2 mm. all plastic components shall be uv-stabilised and weather-resistant to ensure long-lasting performance under outdoor conditions.colour:- paint finish- power coated, uv resistant paint coating thickness (min) 80 micrometer warranty - 3 years. complete in all respects, including installation of equipment in a cement concrete block of size 5 x 5 x 1 , to the entire satisfaction of the engineer-in-charge., providing and fixing of three wheel shoulder builder/ arm wheel- outdoor gym equipment complete in all respects having following specifications. size / dimensions height of central pole from ground -1524 millimeter outside diameter of first wheel - 850 millimeter outside diameter of second wheel - 800 millimeter outside diameter of third wheel - 650 millimeter height of first wheel from ground - 1220 millimeter height of second wheel from ground - 1200 millimeter height of third wheel from ground - 1180 millimeter maximum weight -120 kilogram material:- all the pipes shall be galvanized iron (gi) and isi marked to ensure quality

Central Government/Public Sector

CTN :45166157

19 May, 2026 NA

Delhi - Delhi

Tender For supply of lock retraction pin & chain and foundation plate for c.b.c transition coupling drg. no. sk-62724 item no.15 & 14 alt-18. [ warranty period: 30 months after the date of delivery ]

corporations/Associations/Others

CTN :45151622

18 May, 2026 9.74 Lacs

Chandigarh - Chandigarh

Tender For providing and fixing of children play equipments, open air gym, in various parks in dhanas, chandigarh, under wdf - providing and fixing of swing ( 2 seater) 10 long 8 -6 high & 5 -0 wide made out of 2 m.s. pipe completed as per drg no. 02 job no. m-06 and to the entire satisfaction of engineer-in-charge, providing & fixing of wide slide ssarea : 3.9 m x 1.3 msafe play area : 4.9 m x 2.3 mplatform height : 1.2 mthe wide slide on of the attractive slides of its kind. the chute is made up of 14 swg ss/gi sheet. the stainless steel used is of 304 grades. the chute is supported by 40x5 ms angle. this chute is attached to the platform made from ss/g sheet. the platform is supported by 40 nb gi pipe. the ladder is made using 20 nb and 25 nb gi pipes. the steps for the ladder is made are of 20 nb gi pipes. the sliding height is 2.4m. the landing support used is made up of 25 nb pipe. the handrail of the chute is made up of 20nb power coated gi pipe. the slide is innovative wide slide on which at a time 3 kids can slide., providing & fixing of multi activity play system (ii) (maps ii):deck 3 ht. 1 deck 2.5 ht. 1 frp staircase 3 ht. 1 frp curve slide 3 ht. 1rainbow ladder 1 double swing 1 bubble pannel 1 steering 1area: 7mx5m safe area: 8mx6m 1. deck 3 height & 2.5 height - the deck of maps is made up of 4mm thickness fiberglass reinforced plastic. the top of the platform shall be made up of anti skid surface with multicolored pigment resign. all the attachments is through nylon clamps only. the size of platform is 1.6mx1.6m. 2. frp stairs case - the ladder shall be made up of the fiber reinforced plastic with a thickness of 4mm. it should have reinforcement to maintain strength and avoid bending. 3. frp curve slide- it is made up of 4mm thickness fiber reinforced plastic. 4. rainbow ladder- it is 5 long in height, the main frame of ladder is made up 20 nb g.i. pipe and risers are made up of 40 nb g.i. pipes. 5. double swing.-leg support in 40 nb g.i. pipe and top pipe is made up of 50 nb g.i. pipe seat is made up of 10 mm reinforced rubbers and g.i. pipe should be rubber coated and movement with nylon clamps at top. 6. bubble panel.-the railing is providing to all decks for safety and it is made up of lldpe. 7. steering wheel-it is made up of lldpe., providing and fixing of chest press double complete in all respects having following specifications. size / dimensions- length -1200 milimeter, width- 700 milimeter, height 1800 milimeter maximum weight -120 kilogrammaterial:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength, durability, and corrosion resistance. the main central pipe shall be an 80 mm nb gi pipe, while the handle frame and sheet frame shall each consist of 40 mm nb gi pipes. the connecting links shall be made of 32 mm nb gi pipes, and the footrest pipe shall also be 32 mm nb gi. the mild steel (ms) foundation plate shall have a minimum thickness of 12 mm. the foundation pipe shall consist of a gi pipe anchored 750 mm deep and supported with an ms angle of 25 25 4 mm for stability. the seat and backrest shall be made of high-density polyethylene (hdpe) sheets with a thickness of 3 mm, designed with a uniform bending radius to avoid sharp edges and ensure user safety. all nuts and bolts used for assembly shall be made of galvanized iron (gi) to enhance durability and resistance to corrosion. the movement mechanism shall be fitted with ball bearings that are self-lubricating and sealed to protect against rain, dust, and other environmental elements. the closing caps of open ends of all pipes, as well as bearings, bushes, and bases, shall be covered with fibre-reinforced plastic (frp) closing caps having a minimum thickness of 3 mm. all plastic components shall be uv-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions. colour:- green, paint finish- power coated, uv resistant, paint coating thickness (min) 100 micrometer, warranty - 3 years. co

Central Government And Public Sector

CTN :45153024

29 May, 2026 NA

Raipur - Chhattisgarh

Tender For supply of kit for manganese liners consisting of (1)side frame friction liner to rdso's sk no.69594, alt-3/latest, item no.7, (04 nos) (2)bolster liner to rdso's sk no.77578, alt-5/latest, item no.2, (16 nos), (3)manganese steel liner for wear plate to rdso's drg no.wd-89033-s-01, alt-17/latest, item no.8 (25 nos) (4) silico manganese steel liner to rdso's drg no.wd-93023-s-01 alt. nil/latest, item-2, (02 nos), (5) brake wear plate to rdso sk no.69597, alt-40/latest, item no.09, (05 nos). [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :45125921

18 May, 2026 NA

Mumbai - Maharashtra

Tender For auction sale of rolling stock - condemned diesel loco no. 36157 wds/6 with iron steel and non-ferrous. restricted items: 1. complete bogie frame with wheel set, axel box and gear case = 01 nos., 2. 03 nos. of wheel sets with axel boxes without gear case = 01 nos. removed items: 1. pneumatic valve and air dryer = 01 nos., 2. radiator core = 01 nos., 3. came shaft = 01 nos., 4. extension shaft = 01 nos., 5. lube oil junction 01 and junction pipe 02 = 01 nos., 6. lube oil cooler pipe = 01 nos., 7. lube oil strainer, bottom pipe and cock = 01 nos., 8. steel balo and upper rode lower = 01 nos., 9. water tank = 01 nos., 10. fuel primary filter body and secondary filter body = 01 nos., 11. sensor loader balo = 01 nos., 12. tsc foundation plate = 01 nos., 13. bubble collector pipe ( z pipe, c pipe) = 01 nos., 14. water temperature gauge, pipe = 01 nos. 15. traction motor = 06 nos. remark: 1. restricted items to be returned to the stock holder in good condition by the purchaser at the time of delivery. 2. lot no. is painted on loco. 3. approach road is available up to lot. 4. hsd oil and lubricants if found to be returned to the stock holder. 5. locos are presently stabled at diesel shed kurla. after auction and before handing over, loco will be placed at cla yard for cutting and delivery purpose. purchaser is advised that loco will be placed only after certification of line by sse/pway/mnkd and as advised by sse/d/cla. 6. after purchaser submit all the documents and d.o after auction to dme/d/cla office, sse/d/cla in consultation with sse/p.way/mnkd will decide the date of placement of loco at cutting yard and only after handing over of loco will be done. 6. purchaser has to ensure safety of railway asset and his labour while working in railway premises. if any losses arise due to negligence, the purchaser will be fully responsible. 7. purchaser has to personally visit the site and see the lot. no claim will be entertained after sale of lot. 9. purchaser has to keep enough water/sand at the cutting site. 10.lot is ok for sale. qty : 01 number. location: presently stabled at diesel loco shed kurla. stock holder: dme d cla .

CTN :45083164

12 May, 2026 NA

Multi City - West Bengal

Tender For auction sale of depot ferrous scrap - p.l no. 98050047.scrap c & w fittings consisting of bolster hanger ,anchor link, c buffer flange, control arm assembly, equalising stay, brake head, striker block, face plate, locking plate, spare parts of brake cylinder, crank shaft of main compressor, knuckle, cbc, cbc coupler, axle box , laminated pole shoe, housing, bcn door, tension rod assembly, rear cover, suspension tube, brake beam, dash pot, buffer ,oil thrower, top casting, brake cylinder(ferrous) ,bottom casting, lower spring beam, oxycut ferrous ball bearing, miscellaneousllaneous spares parts of valve & cock, draft pad, screw coupling, yoke , hand bar, pull road, cam shaft, axle cap, ferrous bearing of sorts and sizes, ferrous part of different type of valve, collar, ring, racer, socket head, jumper head, felt ring, ms cylinder, buffer casing, draw bar hook, hanger block, chain bolt, chute plate, wear plate, flap plate, draft gear, gear, pinion, impeller, schaku coupler parts, traction motor parts, nut bolts, pin, icf bogie component and miscellaneousllaneous ferrous etc. as available in lot, except any non ferrous.qty-145mt. location-east of vm road in ncb-12.