Latest gi earth pipe Tenders | Government gi earth pipe Tenders

State Government

CTN :43117013

17 Dec, 2025 NA

Delhi - Delhi

Tender For earthing of various tube wells installed in ward no-180 and 181 under badarpur constituency ac-53. - earthing with g.i. earth pipe 4.5 meter long, 40 mm dia. including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., supplying and laying 25 mm x 5 mm g.i strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with g.i. nut, bolt, spring, washer etc. as required (jointing shall be done by overlapping and with 2 sets of g.i. nut bolt & spring washer spaced at 50mm), providing and fixing 25 mm x 5 mm g.i. strip in 40 mm dia g.i. pipe from earth electrode including connection with g.i. nut bolt, spring, washer excavation and re-filling etc. as required.

State Government

CTN :43117017

17 Dec, 2025 NA

Delhi - Delhi

Tender For earthing of various tube wells installed under kasturba nagar constituency ac-42. - earthing with g.i. earth pipe 4.5 meter long, 40 mm dia. including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing of 6 swg dia. gi wire on surface or in recess for loop earthing as required.

State Government

CTN :43117029

17 Dec, 2025 NA

Delhi - Delhi

Tender For sic of submersible pump set and all allied e/m equipment for rebored tube well near h.no.-116c shahpur jat in greater kailash constituency ac-50. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 10 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point:200 lpm on 90 mtr. head. having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved make, supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted.a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no.b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 noc) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no.e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable bankingg) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos. complete wiring & installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated & pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs.make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., s/o nut & bolts of 1/2 dia of different size i.e. 1.5 dia& 2.5 long full threaded., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 8-10 inch diameter made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2 dia. with locking arrangement by nuts & bolt., earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

State Government

CTN :43117054

17 Dec, 2025 NA

Delhi - Delhi

Tender For providing and fixing of earthing system for protection and safety at various tube wells in chirag delhi under greater kailash constituency ac-50. - earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. (djb sor e&m 2025) 5.2, providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required.(djb sor e&m 2025) 5.16

State Government

CTN :43117061

17 Dec, 2025 NA

Delhi - Delhi

Tender For earthing of various tube well installed in cr park ward under greater kailash constituency ac-50. - earthing with g.i. earth pipe 4.5 meter long, 40 mm dia. including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing of 6 swg dia. gi wire on surface or in recess for loop earthing as required.

State Government

CTN :43134040

30 Dec, 2025 NA

Sikka - Gujarat

Tender For supply of pipes and various rigging material -unit 2500x250 mm board for cup lock scaffolding ,unit 1500x250 mm board for cup lock scaffolding ,scaffolding pipe, galvanized, medium class, 40nb m.s.pipe, length-6mtr ,scaffolding pipe, galvanized, medium class, 40nb m.s.pipe, length-3mtr ,m.s.scaffolding clamp ,ungalvanised steel wire rope dia: 16 mm,6x36 construction, steel core, rhol, tensile strength-1770 ,n/mm2 confirmed to is: 2266/02. ,forged grip (m. s. black)/ u clamp suitable for rope dia 16 mm ,m.s.erw pipe size 65mm x 4.5mm . ,ms black erw pipe 80 mm ,carbon steel 90 deg. seamless bend of size 65 nb, astm-a106, grade-b ,carbon steel 90 deg. seamless bend of size 80 nb, astm-a106, grade-b

Corporations And Associations And Others

CTN :43117081

17 Dec, 2025 67.97 Lacs

Delhi - Delhi

Tender For supply and installation of open gym equipments in najafgarh zone and central zone under mplads funds for various locations of parks in municipal corporation of delhi. - supply and installation of open gym equipments in najafgarh zone and central zone under mplads funds for various locations of parks in municipal corporation of delhi., seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for assembly are of a16. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)., cross trainer /elliptical exerciser dimensions: - 1320mm (length) x 600mm (width) x 1750mm. (height). safe area: - 1.77 x 1.2mtr. cross trainer equipment made from c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the main frame pipes are of 80nb c class g.i. pipe with single bend pipe with 250mm radius. the bottom support of m.s. round plate of dia 250 mm & 10mm thick. the handle frame is made up of 25nb c class g.i. pipe. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. to build structure bushes are used which are made from m.s. seamless pipe of 60mm od with 5 mm thickness. the footrests are made from injection moulded plastic lldpe / hdpe. closing caps are made up of injection moulded plastic lldpe / hdpe. pins used of diameter 35mm, 25mm, and 17mm are made up from sae 8620 bright .the bearings used are of 6007 2rs1 62052rs1 and 62032rs1 permanent lubricated sealed bearing of reputed brand. high tensile steel with galvanized nuts and bolts are used for assembly. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall b

CTN :43102526

18 Dec, 2025 2.38 Lacs

Jaipur - Rajasthan

Tender For ward no. 21 in vidhadhar nagar in patak pachhad hanuman park sector 2 in installing open gym work - cross trainerproviding and fixing of cross trainer of size not less than 1140mm (length) x 625mm (width) x 1750mm. (height), to enhance the mobility of upper and lower limbs and improve the flexibility of joints. the main structure frame shall be made from g.i. pipe minimum of 80nb c class welded with m.s. round base plate at least 250 mm & 10mm thick. the handle frame shall be made up of at least 25nb c class g.i. pipe. the footrests shall be made from lldpe/aluminum casting material of size not less than 130 mm x 310mmx5mm thickness and mounted on m.s. plate of size 130mmx310mmx3mm thick. high tensile steel with galvanized nuts and bolts shall be used for assembly. the powder coating shall be done with pure polyester powders of ackzonoble/ berger/ nerolac paints with 60 to 70 micron thicknesses complete in all respect including fixing the m.s. holdfast in cement concrete to hold the whole structure, under the directions of engineer-in- charge to fulfill the functional requirement., seated pullerproviding and fixing of seated puller of size not less than 2400mm (length) x 800mm (width) x 2000mm. (height), to enhance the strength of upper limbs and the muscles in chest and back and promote cardio-pulmonary function. the main structure frame shall be made from g.i. pipe minimum of 100nb c class welded with m.s. round base plate at least 250 mm & 10mm thick. the handle frame shall be minimum of 32nb c class g.i. pipe. the seat frame minimum of 50nb c class g.i. pipe, closing caps shall be made up of lldpe/high quality fiber reinforced plastic material. high tensile steel with galvanized nuts & bolts shall be used for assembly. the powder coating shall be done with pure polyester powders of ackzonoble/ berger/ nerolac paints with 60 to 70 micron thickness complete in all respect including fixing the m.s. holdfast in cement concrete to hold the whole structure, under the directions of engineer-in-charge to fulfill the functional requirement., chest pressproviding and fixing of chest press of size not less than 2200mm (length) x 800mm (width) x 2000mm. (height), to enhance the strength of upper limbs and the muscles in chest & back and promote cardio pulmonary function. the main structure frame shall be made from g.i. pipe minimum of 100nb c class welded with m.s. round base plate at least 250 mm & 10mm thick. the handle frame shall be made up from at least 32nb c class g.i. pipe. the seats and back rests to be fitted on the outer frames shall be made up of m.s. sheet of size not less than 330mm x 300 mmx2mm thickness. closing caps shall be made up of lldpe/high quality fiber reinforced plastic material. high tensile steel with galvanized nuts & bolts shall be used for assembly. the powder coating shall be done with pure polyester powders from ackzonoble/ berger/ nerolac paints with 60 to 70 micron thickness complete in all respect including fixing the m.s. holdfast in cement concrete to hold the whole structure, under the directions of engineer-in-charge to fulfill the functional requirement., pommel horseproviding and fixing of pommel horse of size not less than 2150mm (length) x 800mm (width) x 800mm. (height), to enhance the flexibility of lower limbs, waist and abdomen. the main structure frame shall be made from g.i. pipe minimum of 80nb c class welded with m.s. round base plate at least 250 mm & 10mm thick. the handle frame be minimum of 32nb shall be made from c class g.i. pipe. closing caps shall be made up of high quality fiber reinforced plastic material. high tensile steel with galvanized nuts and bolts shall be used for assembly. the powder coating shall be done with pure polyester powder ackzonoble/ berger/ nerolac paints with 60 to70 micron thickness complete in all respect including fixing the m.s. holdfast in cement concrete to hold the whole structure, under the directions of engineer-in-

CTN :43093912

12 Dec, 2025 8.41 Lacs

Sawai Madhopur - Rajasthan

Tender For work of installing open gym equipment in ambedkar park ward no. 14 municipal council area. - based on ruidp 2023, air walker: providing, designing and fixing of air-walker of size 1100 x 550 x 1480mm fabricated with main post of 114mm dia and 2.5mm thick and other pipes of 40mm dia 2.5 mm thick made up of hot rolled tubular steel and hot dipped galvanized and powder coated 80-120 micron thick using akzo nobel or equivalent in desired shade and colour. all welding joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all the welding points prior to finishing. all open ends of pipe to be closed with gi/ lldpe caps, base plate cover shall be made of virgin lldpe plastic by rotational molding with minimum 3mm thickness, uv resistant and colour as approved by engineer in charge. high quality grip rubber should be used on handles. foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. maintenance free bearings should be used in the equipments manufactured by reputed company duly oil sealed and self lubricated to be approved by engineer-in-charge. the equipment shall be fitted with in-built limiters. the equipment shall be fixed on ground with concrete of minimum strength m-25 and j shaped welded bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover, all complete as per directions and approval of engineer-incharge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc (the cement concrete and excavation work shall be paid separately)., sit up station: providing, designing and fixing of double sit-up station of size 1500 x 1150 x 650mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe of 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using akzo nobel or equivalent of 80 - 120 micron thick. all joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. seat and base plate cover to be made up from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic as 3mm, colorful and uv resistant and environmental friendly. the equipment to be fixed on ground with concrete of minimum strength m-25 and j shape welded bolts and once the concrete is set, fix the equipments on to it and cover nuts and bolts with the base plate. all complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal) and fixing of equipments etc. (the cement concrete and excavation work shall be paid separately)., air swing: providing, designing and fixing of air swing in pair of size 1150 x 900 x 1250mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using akzo nobel or equivalent of 80 - 120 micron thick. all joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. pedals shall be made of nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic of 3mm, colorful and uv resistant and environmental friendly. bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted with inbuilt limiters to prevent unwanted movements. all open ends of pipe to be closed by gi/ lldpe caps for user safety. the equipment to be fixed on ground wi

Central Government/Public Sector

CTN :43109839

30 Dec, 2025 NA

Sonitpur - Assam

Tender For provn of covered shed with galvanized roof top and brick wall with frame at 180 mh and special repair to existing external water supply pipe line of asc coy under ge missamari

Gi Earth Pipe Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors