Latest glass sleeve Tenders | Government glass sleeve Tenders

State Government

CTN :43117029

17 Dec, 2025 NA

Delhi - Delhi

Tender For sic of submersible pump set and all allied e/m equipment for rebored tube well near h.no.-116c shahpur jat in greater kailash constituency ac-50. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 10 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point:200 lpm on 90 mtr. head. having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved make, supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted.a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no.b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 noc) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no.e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable bankingg) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos. complete wiring & installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated & pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs.make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., s/o nut & bolts of 1/2 dia of different size i.e. 1.5 dia& 2.5 long full threaded., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 8-10 inch diameter made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2 dia. with locking arrangement by nuts & bolt., earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

State Government

CTN :43117039

17 Dec, 2025 NA

Delhi - Delhi

Tender For supply of 2.5 mgd pump for set no-2 at babu park kotla bps. - supply of horizontal split casing pump set with impeller(ss), neck ring (ci casing (ci) & shaft sleeve (ss-410) with suitable bearing havine following duty point:-head: 40 mtr.discharge : 500 m /hrrpm: 1480suction / delivery size:- 200 mm x 200 mm pump make:: m&p/ jyoti/ lubi/ kirloskar / any djb approved make.

State Government

CTN :43122894

15 Dec, 2025 4.95 Lacs

Kheda - Gujarat

Tender For supply of routine maintenance items- crimping type non-insulated copper pin type terminal end 25 sq.mm , crimping type non-insulated copper pin type terminal end 35 sq.mm , crimping type non-insulated copper pin type terminal end 50 sq.mm , 300 sqmm crimping alluminium type in-line connectors , 240 sq mm crimping type alluminium in-line connector , 185 sqmm crimping alluminium , type in-line connectors cat no :hai-11 hex make , aluminium tube terminals 185.0 mm2, m10 , aluminium in line connector 70 mm2 , aluminium in line connector120 mm2 , 35mm alluminium in line connector als-2 dowell" , heat shrinkable sleeve for lighting wiring , heat shrinkable sleeve, size:45mm/18mm(for 240/300 sq.mm )for 11 kv , 1.1 kv busbar/cable couductor protection heat shrinkable sleeve diabefore shrink: 50 mm dia. after shrink: 16 mm for 1.1 kv lt cable , double pole mcb-2a , mcb/dp, 6a , indication lamp , mcb dp 16a ac, c-curve, csmbs2c16 , mcb dp 10a ac, c-curve csmbs2c10 , gls lamp 500 w screw type , plastic dori (sutari) for binding of plastic 0.5 thick &2mm width. , to make panelspare handle cssdf200a-400amp (cswh 145 s 12) , thinner for enamel paint. (tin of 1 ltr.) , multi functional fluid spray oks-601 , carbon cleaner spray , painting brush size 3" (75 mm) , painting brush size-38 mm , wire brush size 12" with wooden handle , washing powder (1 kg pack) , pvc buckets-15ltr , schneider , telemechanique/merlin gerin , make-push button for 22.5 panel , cutout with contact , elementtype of contact , :nocolour: yellowreferance , no.:xb5-aa51ntype:spring return , push buttons , oks 2621 safe l.c. spray, contact cleaner spray for live circuits 500 ml spray bottel) , flat cable 3 corex4 sqmm with copper conductor for submersible motor , pvc insulated, unsheathed flexible copper cable size 1 core x 2.5 sq. mm, 1100 v grade , auxiliary relay re-300 coil voltage 250v dc , jyoti make re-300 plug in type , relay, coil voltage 240 v,50hz ac with led indication & 4 change over contact having 10 amp rating. , tubular spanner set (8 pcs) , product no ts 08 taparia make , bimetal mini hole saw cutter complete with arbor, product no- hsm 12, size-12 mm , bimetal mini hole saw cutter complete with arbor, product no- hsm 19, size-19 mm , bimetal mini hole saw cutter complete with arbor, product no- hsm 22, size-22 mm , oil barrel hand pump , electrical hand blower 800 watt, 230 volt, 50hz , hand grinder machine. , #w963 play safe high voltage tape (25 mm x 0.76 mm x 9.1 mtr) roll , w963 play safe high voltage tape (50 mm x 0.76 mm x 9.1 mtr) roll , control transformer, 440v/240v, 250va , on/off selector switch, model: s16-61002-803, ac23a-10hp make: , salzer , on/off selector switch, model: s6-61002-b13, ac21a-440v-6a make: salzer , voltmeter selector , switch, model: s10-61100-b13, ac23a-4hp, 440v ac make: salzer , bus selection selector , switch, model: s6-61038-b13, ac23a - 3 hp make: salzer , voltmeter selector switch, 6a-vss-b13, ac21a, 440v, 6a make: salzer , local/remote selector switch, model: d16-61040-863 3.16a, dc22a, l/r-2 m.sec, make: salzer , ammeter selector switch part code-6a-s6-61325-b13-tdyr make-salzer , stanvac pen oil rust remover 6030,500 ml/pac , control transformer pri:0-375.5-415v 50hz blk-blu-brn sec:18v, 1.2a blu-blu 24v,3.2a brn-brn sheild:yel/grn burden 100va, 1ph , petroleum jelly 1kg pouch packing , safety solvent co2 contact cleaner. , #901 easyclean (nf) 500 ml. spray canon line electrical contact cleaner.

State Government

CTN :42807879

16 Dec, 2025 27.40 Lacs

Sarni - Madhya Pradesh

Tender For corrigendum : procurement of spare of mechanical seal of make flowserve for bfp model no. fk6d30 and booster pump model no. fa1b56 for aoh of unit no. 10 and breakdown maintenance of unit no 10 and 11 of ph-iv, stps, sarni. - procurement of spare of "mechanical seal" of make "flowserve" for "bfp model no. fk6d30" & "booster pump model no. fa1b56" for aoh of unit no. 10 and breakdown maintenance of unit no 10 & 11 of ph-iv, stps, sarni. - spares for mechanical seal of make flowserve type hs 5.500 drawing no. "3h-36560" for bfp model no. fk6d30 , seat ring carbon, part no. 03, mat. code-kr3n5500ae3, insert, part no. 2, mat. code-av3h5500ha3, set of o ring, mat. code-fk-6d 50:sop, set of springs, part no. c, mat. code-mbax8840307, sleeve, part no. 10, mat. code-19865sse5500, insert mounting gasket, part no. 6, mat. code-mvsr5000333, set screw , part no. 13, mat. code-mqax8840417, drive pin, part no. d, mat. code-mkax8840288, drive pin, part no. d1, mat. code-mkax8840212, cap screw, part no. k, mat. code-meax8840663, gasket, part no. g1, mat. code-mvsr7750333, gasket, part no. g2, mat. code-mvsr8000333, sleeve packing, part no. 11, mat. code-mvsr3750333, ecc washer, part no. 15, mat. code-meax1476433, shaft packing, part no. p, mat. code-mvsr5500333, gasket, part no. g, mat. code-mvsr7250333, spares for mechanical seal of make flowserve type pto 4.250 drawing no. "2h-97621" for "booster pump model no. fa1b56 , 4.250" pto tung-car seal ring, part no. 3, mat. code-ku3t4250333, #5 carbon insert, part no. 2, mat. code-97628y3r4250, set of o ring, mat. code-2h-97621:sop, set of springs, part no. c, mat. code-mkax8840301, 316 ss sleeve, part no. 10, mat. code-97629sse4250, set screw, part no. 13, mat. code-mqax8840417, insert mounting-viton, part no. 6, mat. code-mvrr4625333, sleeve packing-viton, part no. 11, mat. code-mvsr3125333, eccentric washer, part no. 15, mat. code-mca13212733, drive pin, part no. d, mat. code-mkax8840212, drive pin, part no. d1, mat. code-meax88402at, spring pin, part no. e, mat. code-mkax8840217, gasket, part no. g, mat. code-mt3g6750ap3, bolt, part no. m, mat. code-pbltc1024#02, shaft packing, part no. p, mat. code-mvrr4250333

Central Government/Public Sector

CTN :43112043

30 Dec, 2025 20.25 Lacs

Sidhi - Madhya Pradesh

Tender For supply of pneumatic lower repair kit part no. 344555 , pneumatic motor repair kit part no. 344666 , injector cap and o ring part no. 400128 , pneu solenoid valve part no. 350006 , 3000mm hose with stud both side part no. 530042 , follower plate part no. 350503 , fm-01 injector part no. 400100 , 2 bank injector with manifold part no. 400117 , 3 bank injector with manifold part no. 400118 , 4 bank injector with manifold part no. 400119 , zerk fitting part no. 400127 , pneu vent valve part no. 400400 , pneumatic vent valve repair kit part no. 400475 , lubrication controller lc-02 part no. 400702 , pipetube rs part no. 400706 , 1700mm hose with stud both side part no. 530041 , polyamide hose 8. 4mm od-4mm id 50m part no. 801001 , 1500mm hose with stud both side part no. 530043 , 1400mm hose with stud both side part no. 530044 , 8000mm hose with elbow and swivel nut part no. 530045 , hose stud part no. 600004 , hose sleeve part no. 600005 , ddr part no. 600013 , pressure gauge 0 - 400 bar part no. 600016 , spray valve nozzel part no. 600041 , elbow we 1 by 8m npt x 7 by 16 unf m part no. 600119 , elbow we 1 by 4m npt x 7 by 16 unf m part no. 600120 , straight ge 1 by 4m npt x 7 by 16 unf part no. 600310 , extension adaptor 1 by 8m x 1 by 8f 15mm part no. 600202 , quick release coupler part no. 601001 , muffler part no. 333029 , fm-01 injector repair kit part no. 400175 , jaguar head repair kit part no. 344888 , air filter regulator unit frl part no. 600020 , jaguar pump station assy 50 kg part no. 350500

Central Government And Public Sector

CTN :43109425

30 Dec, 2025 NA

Chittorgarh - Rajasthan

Tender For supply of spare of pump : : -impeller spare for pump model noppe 40n 160 , gasket impeller spare pump model no ppe 40n 160 , gasket casingspare for pump model noppe 40n 160 , shaft spare for pump model noppe 40n 160 , set of inboard and outboard oil seals , volute casing , backplate for gland packing with flange and cft bush , suction flange , discharge branch , discharge flange , gland pusher with cft bush , bearing cup , shaft sleeve , circlip , nipple , breather

Central Government And Public Sector

CTN :43114406

31 Dec, 2025 NA

Narora - Uttar Pradesh

Tender For supply of spare bearings for m/s hydrodyne teikoku make canned rotor pump model no- hd 32-250/15h2/gb , spare shaft sleeve for m/s hydrodyne teikoku make canned rotor pump model no- hd 32-250/15h2/gb , spare thrust washer for m/s hydrodyne teikoku make canned rotor pump model no- hd 32-250/15h2/gb , spare bearing wear monitor for m/s hydrodyne teikoku make canned rotor pump model no- hd hd 32-250/1 , spare o-rings for m/s hydrodyne teikoku make canned rotor pump model no- hd 32-250/15h2/gb

Central Government/Public Sector

CTN :43116350

23 Dec, 2025 2.00 Lacs

Leh - Jammu And Kashmir

Tender For supply of 206043100101 clutch kit , 257329100161 sleeve cyl kit , 264143700106 air dryer assy , 252340150123 air dryer maj kit , air comp kit , 2530004635 cross kit , 275225400105 pressure plate , 263254209911 speedo cable , 263754209952 speedo meter head , gear lever kit , seal rotor pump , rotory key , 2523 0913 0168 pre cleaner filter

State Government

CTN :41739284

18 Dec, 2025 5.22 Lacs

Multi City - Telangana

Tender For corrigendum : supply of spare parts for raw water pump - cut less bush(suction bell),material:rr backed by metal,part no:4 for raw warter pump model- vt-39-19, , lock collect , material:ss410,part no:8 for raw warter pump model- vt-39-19, , cut less bush(internal bowl),material:rr backed by metal,part no:10 for raw warter pump model- vt-39-19, , cut less bush (discharge case), material:rr backed by metal,part no:12,for raw warter pump model- vt-39-19, , pump shaft, material:ss410,part no. 14 for raw warter pump mdl vt-39-19, , shaft coupling (thd), material:ss410,part no:15,for raw water pump model-vt-39-19, , sleeve line shaft material:ss316,for raw water pump model:vt-39-19 , cut less bush (line shaft ), material:rr backed by metal,part no:19,for raw water pump model,vt-39-19, , bottom head shaft material:ss410,part no:22a,for raw water pump model-15,vt-39-19, , deflector,material: rubber ,part no.31 for raw water pump model vt-39-31, , head shaft, material:ss410,part no. 41 for raw water pump modelvt-39-19, , bush retainer,matreial:csa216,p/n:19a,for raw water pump mdl: vt-39-19, , line shaft, material:ss410,part no.17 for raw warter pump modelvt-39-19,

CTN :42828879

17 Dec, 2025 NA

Etawah - Uttar Pradesh

Tender For corrigendum : tender for supply of wick long tab , valve plug , o ring ohaulingkithp pumpseal retainer , front , anode plug , hp pump seal kit , oil filler cap , oil seal crankshaft , plunger rod pin , v-packing case , hp pump female adapter , hp pump male adapter , valve spring retainer , valve plug 70 kg , hp pump anode plugs , seal kit , valve set , oil seal crankshaft , connecting rod assebly , plunger rod , plunger rod pin , oil seal crank case , seal retainer - 2 pc , barrier slinger , hp pump inlet manifold , adaptor h.p.pump , male adaptor , v packing spacer , spacer with coil springs , valve plug 70kg , o ring overhauling kit , crankcase casing , straight connector 3-8 , permeate male elbow , cartridge filter element , nozzleset for filter consist of filterhead tube strainer , frp filter type 1354 , nozzle set for frp filter 1354 , nozzle set for sand filter , head distributor , media for sand filter grade-i , support gravel 1.5-3.0 mm , support gravel 2.0-3.0 mm , dolomite , membrane cleaner 22 , membrane cleaner 33 , membrane solution 44 , h.p pump c case oil , jubilee clips 00 13 mm to 20 mm , s.s jubilee clips 1x 30 mm to 40 mm , ss jubilee clips 2x 45 mm to 60 mm , high pressure manifold 3 x 2 arrangement , high pressure manifold 6 x1 , module bypass nozzle , support bracket , pure water manifold , pu9 hose , tie rod nut high , h p connection feed/brine , lip seal dt module , membrane cushion , blue hydraulic disc , o ring for head distributor assembly , o ring hp connection , o ring hydraulic disc , o ring distance fitting inside , o ring distance fitting outside , o ring tie rod screwing inside , o ring crank case cover , o-ring pos. no. 412 for speck pump npy 2051 , high pressure hose module outlet , hp flexible hose , h.p hose feed inlet-brine outlet , brine r/w h.p. flexible hose , brine r/w hp flexible hose-xl , brine raw water high pressure , rubber hose from c-f outlet to hp pump inlet 20-30tpd , lp hose for prefilter pump , hose for pk-20 pump in-out , product water flex hose-fm manifold to plant , lp hose brine - permeate , end conn hoses brine/permeate , rubber hose 20mm , lp hose for air line , av mount akcc 85m , mounts for plant , a/v mount for hp pump trolly , h.p pump driving belt set of 2 , coupler for victaulic coupling 1 , victaulic couplers 1.1-4 , belt spanner , pulsation damper , jubilee clip 40mm , membrane solution 44 , pressure switch , belt hp pump driving , hp pump anode plugs , contractor , o-ring for deacidification filter , o-ring for cartridge filter , kit wear parts , sleeve gasket , neck ring p 45 , neck ring retainer , motor for 30tpd filter prefilter pump , mechanical seal p 105 , sleeve gasket p 37 , corrugated spring p 60 , spacing pipe - 66.a , bearing ring p 47a , spacing pipe -p 64.c , slotted nut p 67 , coupling complete for pump 202699 p 8 , stay bolt for pump p 26 , chamber complete p 4 , neck ring p 45 , neck ring retainer , pump shaft complete for pump 202699 p 51 , chamber with bearing ring p 4a , impeller , spacing pipe - p 64.a , wear part kit - repair kit , split pin , ball bearing , p 154 , shaft pin p-10 , top guide vane p 50a , spacing pipe p 64 , chamber stack for pump 202699 p 80 , chamber , crn 1- 4 pump spindle , crn 1- 4 pump shaft seal p-105 , o-ring 137.5 od x 3.3 thk , shaft pin 50d x 26l , o-ring 16.3od x 2.4 thk 100 , neck ring , neck ring retainer , impeller 30.6id x 73 od x 9h , shaft seal , chamber with bearing ring , neck ring retainer , chamber with bearing ring) , shaftseal p105 , kit , gaskets , cm 3-5 pump 415v 3ph 50hz.ip55 , cm 3-5 sleeve p-16 , cm 3-5 impeller p-49 , chamber , seal ring , filter pump permeate pump , filter permeate pump casing , ring-circlips p-931 , filter permeate pump grub screw , o ring , shaft seal , casing p-1 , reverse vane impeller , p-2b , shaft p-6 , cover for mech seal , sleeve shaft p-14 , i b bearing p-16 , o.b. bearing p-18a , circlip internal p-18b , oil drain plug

Glass Sleeve Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors