Latest rails Tenders | Government rails Tenders

Central Government/Public Sector

CTN :45302387

28 May, 2026 NA

Multi City - Gujarat

Tender For auction sale of others - abandoned old buildings/sheds/structures of mg workshop- 04 units, unit no. 19 - small shed near dome, unit no. 22 - record room, unit no. 23 - dwm office, unit no. 24 - machine and generator room location - mg workshop bvp. this lot of abandoned condemned buildings consisting of released door with chokhat wooden u/s - 3 nos, released window with chokhat wooden u/s - 41 nos, released wood - 1.296 cum, released ac sheet approx. - 433 sqm, released steel door u/s - 60 kg, released manglore tiles approx. - 620 sqm, released rails from structures u/s [41.25.50r & other miscellaneous type of rail off sizes] - 896 kg, ms scrap. i.e tie bar, flat, angle, fish plate, nut, bolt, ms sheet door, steel bar, gi sheet, xpm jalli etc. off size approx - 6726.7 kg, released masonary /rubble approx - 290.9 cum. custodian - sse (w) bvp, mode of delivery by lot, loading by purchaser. note: 1. dismantling is permitted up to ground level only. digging below ground level is not permitted. due care is to be taken by the bidder/purchaser to avoid unwanted mishapes at work spots. they should ensure to keep a safety banner around the work spot till it is completed since the locations are surrounded with working offices. 2. after removing/ clearing the rcc/ brick machonary rubbish from the spot only, the delivery of wood/ iron material will be affected. 3. contractor should take care of any cable while dismantling and digging. damage to railways shall be recovered as per extent rules. 4. part delivery/ part handing over is not allowed. 5. any ng/mg/bg pway rail lines or pway scrap with or without attachments lying under or beneath the building/sheds/structures or surrounding area are not deliverable. 6. any non-ferrous material of high value if found from the lot, it needs to be submitted by the purchaser to the custodian. 7. power of attorney along with aadhar card/identity proof/address proof must be submitted to this office for verification of authorised person by bidder before handing over (if any.) fdp 50 days.

Central Government/Public Sector

CTN :44711948

28 May, 2026 NA

Bhopal - Madhya Pradesh

Tender For bid to ras corrigendum : supply of finished thrust bush for thrust and guide bearing assy. to drg. 24025442039, var. 00, rev. 00. , finished guide bush for guide bearing assy. to drg. no. 34028042043, item-01, rev. 05. , finished guide bush for guide bearing assy. to drg. no. 34028042044, item-01, rev. 04.

State Government

CTN :45287352

29 May, 2026 NA

Khaperkheda - Maharashtra

Tender For procurement of spares of tg servomotor for coh of unit no. 3. -0 c/vlv sm compression sprng, c/vlv sm bush drg no 0114022400003023, c/vlv sm pilot vlv dia80, c/vlv sm bush 80 drg no 0114022400003020, tbnsteam 210mw c/vlv sm guide drg no, hpcv sm rod drg 01140224000 item 013, hpcv sm lever drg 01140224000 item 011, hpcv sm feed back cam drg01140224000 009, c/vlv sm bush drg no 0114022400003008, c/vlv sm bush drg no 0114022400003005, c/vlv sm piston drg no 0114022400003004, c/vlv sm bush drg no 0114022400003003, c/vlv sm piston rod drg0114022400003001, hpcv sm disc spring drg 01140224000, ipcv sm sm compression sprng, ipcv sm sm bush d-80 drg0114040300001021, ipcv sm sm ipcv sm drg0114040300001000, ipcv sm sm threaded bush, ipcv sm sm piston drg0114040300001004, ipcv sm sm guide bush

Central Government/Public Sector

CTN :45305070

01 Jun, 2026 NA

Multi City - Chhattisgarh

Tender For scope of work (sow) as mentioned in tender and schedule of work( 34 )items as given below ,[1] reprg of cyl hyd pumps motr rllr of wap 150.000 set,[2] techlgl upkpmt of hyd+pneum systm of wap 90.000 set,[3] repr g.box dr.mech of convr.crn.chgr.mnp 90.000 set,[4] struc repg-fce convr chut chrgr crn+pipe 60.000 to,[5] maint. of manipulator cross rails 72.000 set,[6] maint. of manipulator long travel rails 72.000 set,[7] fab & chnging of gas lines of a & b fces 150.000 m,[8] fab,rep,chnging of diff size water lines 60.000 le,[9] clng of pipe trench and surrndng 60.000 le,[10] dismantlg,fab,erec 8in dia headers 198.000 m,[11] dismanlg,fab,erec of diff dia brnch line 147.000 m,[12] rep water filtrn unit of compr waterline 30.000 le,[13] servg/chng gate v/v of diff sizes 90.000 ea,[14] disman,lid,table,lid 30.000 set,[15] repair,str frame 24.000 to,[16] clean&overhaul,mech parts 24.000 set,[17] svce speed change,g/box 108.000 set,[18] replcg,locking lever assy 108.000 set,[19] clng,blade tensioning guide area 96.000 set,[20] remove,incoming&og roller tables 96.000 set,[21] svcg,pusher mechanism 90.000 ea,[22] svcg,swing hyd cyl,6set 54.000 ea,[23] svcg,hyd cyl,6nos 54.000 ea,[24] svcg,front vice operating hyd cyl 54.000 ea,[25] up keepg,floor area 3600.000 m2,[26] rprg,damaged coolant pipeline 1950.000 ft,[27] svcg,rotating roller table g/box 54.000 ea,[28] rprg,roller side guard&floor plate,fixg 36.000 to,[29] svcg,pwr pack 36.000 set,[30] svcg,gravity roller conv after weigh m/c 18.000 set,[31] clng,coolant tank&vice bed every week 54.000 set,[32] svcg,pneumatic line&vlv 54.000 set,[33] fab,str etc f/stacking matl 12.000 to,[34] replcg,lt driving&non-driving wheel assy 36.000 ea

Central Government / Public Sector

CTN :44934120

26 May, 2026 NA

Jeypore - Odisha

Tender For jeypore -nabarangpur new railway line project: construction of new bg railway line between ambaguda (excluding) (13.60 km) to nabarangpur(including) (43.99km) involving earthwork in formation in embankment/cutting, blanketing, side drains, catch water drains, minor bridges, major bridges (excluding br.no.85 at km 37.080 i.e indravati bridge) , road over bridges (robs), road under bridgees (rubs), protection works, p.way track works with contractor's own material supplies including supply of track ballast, new wide based psc sleepers, special psc sleepers (for turnouts, improvised sejs, guard rails etc.), points (thick web switches) & wcms crossings, glued joints, h-beam/composite sleepers over girder bridges, improvised sejs, all p-way fittings, 2x25 kv ac ohe works, 2x25 kv tss with sp/ssp works along with scada, modification/conversion to underground for overhead electrical ht/lt power line crossings, electrical general services, construction of platforms, station buildings, service buildings, sp/ssp buildings, trd depot building with tower wagon shed, residential buildings, water supply, indoor and outdoor electrification etc. on epc basis in waltair division of east coast railway.

Central Government / Public Sector

CTN :44436691

26 May, 2026 NA

Jeypore - Odisha

Tender For corrigendum : jeypore -nabarangpur new railway line project: construction of new bg railway line between ambaguda (excluding) (13.60 km) to nabarangpur(including) (43.99km) involving earthwork in formation in embankment/cutting, blanketing, side drains, catch water drains, minor bridges, major bridges (excluding br.no.85 at km 37.080 i.e indravati bridge) , road over bridges (robs), road under bridgees (rubs), protection works, p.way track works with contractor's own material supplies including supply of track ballast, new wide based psc sleepers, special psc sleepers (for turnouts, improvised sejs, guard rails etc.), points (thick web switches) & wcms crossings, glued joints, h-beam/composite sleepers over girder bridges, improvised sejs, all p-way fittings, 2x25 kv ac ohe works, 2x25 kv tss with sp/ssp works along with scada, modification/conversion to underground for overhead electrical ht/lt power line crossings, electrical general services, construction of platforms, station buildings, service buildings, sp/ssp buildings, trd depot building with tower wagon shed, residential buildings, water supply, indoor and outdoor electrification etc. on epc basis in waltair division of east coast railway.

State Government

CTN :45304509

18 Jun, 2026 28.00 Lacs

Alappuzha - Kerala

Tender For purchase of 4cti engine spares - 4cti engine spares, interference fit liner-w f9k00122, interference fit liner-x f9k00222, interference fit liner-y f9k00322, interference fit liner-z f9k00422, cylinder head fcn04822, valve seat exhaust x0900116, valve seat intake x0900216, valve seat kit p3118951, valve bush- bushing valve guide intake f0531522, ball steel f4832510, stud-exhaust manifold x3504211, cylinder head cover f1135842(b8254309), oil filler cup f1100160, cylinder head cover gasket f1762100, gasket-cylinder head fct00800, valve guide kit p0991151, thrust washer std p0990951, crank shaft main bearing std p0928851, ring set p0982751, piston set p0982651, con rod bearing kit -std p5104212, bushing con rod f0537930, bolt con rod f3585615(p8100335), twin groove add on pully fc803422, starting ring f0741822, crank shaft rear end oil seal x2705100, o ring-81.2*3.3 f2744200, front and oil seal fe802900, composite valve kit p0951051, valve stem seal x2706400, exhaust manifold x1813022, gasket -emd fff00213, hex nut flunged m10* 1.25 f7f00115, stud m8*1,25-43mm long x3714015, throttle and gear operating unit(twin engine type), mac n hom steering unit, mac n hom actuvator, inter cooler, knr pump, oil pressure sensor fmk00200, temperature sensor x2009400, gear oil pressure guage, rubber packing 3mm, graphite packing 3mm, alied packing 3 mm, diesel filter fhj00700, air filter element(primary and secondary), coolant-72 litre(24can-1 can-3 litre), rubber hose id 1 1/4" marine hose, rubber hose id 1.5" marine hose, rubber hose id 2" marine hose, rubber hose id 3" marine marine flame resistant, glass doom and o ring, bend rubber hose, sea chest brass gate valve 2 inch, non return 1 3/4 inch, coupling bolts5/8* 4, inter cooler, gear cooler, oil cooler 6 plate fp405700, filter element oil(micro flow) p31015410, breether hose with inner spring b7015701, h4 injector hp pipes kit b5h07209(b5h03404), pipe oil b7007801, lube oil feed pipe for fuel injection pump b9723006, s/a injector leak of pipe b9221205, injector for 135 lt bs3 engine f8x00210, gasket nozzle holder f1761300, coolant pump assy (fwp) b8760406, turbo charger a4k09900-alesc43-a, belt 8 pk1250(fenner) x0301650, v belt f0330950(x0300450), pipe-heat exchange to cac-in frr00135, hose assy-feed pump to fuel filter b3j00502, expansion bellow-exhaust 4 hole type f3l02014, banjo bolt m12*1.5 f2804611, banjo bolt m14*1.5 f2804711, heat exchanger f3953600, cable- accelerator remote control f0l01000, charge air cooler marine engine faf07600, pipe-turbo to cac frr42615, adaptor to he connection fot27911, hose f1974150, hosestraight 26 id marine app x0w24658, pipe-he to cac in frr00135, hose f1925250(f8p13358), hose straight x0w23258, hose clamp f0819210, pipe sw out to he in frr39915, pipe f8632610, bracket heat exchanger xjw00714, hose b3j00501, pipe he out to cac in marine frr40215, bracket heat exchanger xjw00414, hose clamp x3901010, pipe radiator fresh water outlet ft723014, pipe radiator to engine air intake ft723414, low oil pressure switch with sensor fmk00200, hose single bend l bow fx216158, silencer f3950614, l-hose f1970750, straight hose for radiator pipe line f1971550

CTN :44042341

27 May, 2026 NA

Mumbai - Maharashtra

Tender For bid to ras supply of prelaminated mdf board (q3) , foam size 6 feet x 3 feet 100 mm th 40 density , veneer sheet 3mm of size 8 feet x 4 feet of approved shade , veneer sheet 6mm th of size 8 feet x 4 feet of approved shade , top of table dinning size 2100 mm x 1050 mm for 8 pers size of 18mm bwr grade i , laminated sheet 1mm thick size 8 feet x 4 feet , 1st class timber wood beating 20mm x 4mm thick , teak woodlegs size 35mm w x 40mm h x 450mm i for chair dining , arm rest teak wood of size 75 x 25 x 610mm for chair easy duly french polished , lakhdana , teakwood legs size 750mm h x 90 mm h x 45mm b for table dining 6 8 pers , 5mm thick glass sliding for dressing table ladies fd 251 size 300 x 300mm , piano type continuous hinges 20mm wide 5m long , teak wood front rail side 100mm i x 35 mm w for sofa , teak wood front legs size 75mm i x 35 mm b x 300 mm h for sofa , top of table peg of size 450mm x 300mm x 380mm madeup of 18mm th bwp grade a , teak wood arms rest of size 70mm x 30mm x 700mm , 75mm long s s handle for ladies dressing mirror , teak wood front legs size 55mm i x 30 mm b x 685mm h for chair writing , nuts and bolts 2 and half inch x 3 by 16 , bee wax white powder , s s 50mm knob hnadle for bed side table map , mirror 5 point 5 mm thick size 1200mm x 600mm for gents mirror , front teak wood leg of size 65 x 35 x 935 for chair dining wooden , hard rubber shoe 20mm dia , nut and bolt 100mm long , nails 2 inch , nails 3 inch , teak wood rear leg of size 70mm x 30mm x 700mm , teak wood legs for table writing as per sample , hard pvc ring 20 mm dia for chair as per sample , hnadle cp 150 mm for almirah with shelves , wooden screw shaved lead 35 mm 8 no 200 nos in a pkt , cp decorative handle 100 mm for almirah , wooden screw shaved lead 50 mm 8 no 200 nos in a pkt , wooden screw shaved lead 60 mm 8 no 200 nos in a pkt , nails 1 and half inch , glass 5mm th of size 300mm x 440mm for hat stand , screw 1 inch half threaded galvanized screw per pkt 200 nos , nails 4 inch , teak wood rails size 20mm b x 40 mm i x 450 mm h for table peg , panel pin 25mm with head , screw 2 and half inch half threaded galvanized screw per pkt 200 nos , screw 2 inch half threaded galvanized screw per pkt 200 nos , panel pin 25mm w o head , wooden screw shaved head 3 by 4 inch 200 nos in a pkt , screw 1 and half inch half threaded galvanized screw per pkt 200 nos , wooden screw shaved lead half inch 200 nos in a pkt , wooden screw shaved head 25 mm 6 no 200 nos in a pkt , screw 3 inch half threaded galvanized screw per pkt 200 nos , panel pin 3 by 4 x 19 , panel pin 20mm w o head , bow handle 100 mm aluminium , clips for fixing almirah shelves , panel pin 19 x 1 , veneer sheet 4mm th of size 8 feet x 4 feet of approved shade , foot rest for bed made out of seasonal teak wood with arm with 4mm plywood , head rest for bed made out of seasonal teak wood with 4mm plywood //bid details2 / 47

CTN :45319562

08 Jun, 2026 NA

Parganas - West Bengal

Tender For supply of hsr45lr2ssco+ 2060lp-ii linear guide way (2rails+ 4blocks) . , hsr45la2ssco+ 1440lp-ii linear guide way (2 rails+ 4 blocks) .

CTN :45308068

12 Jun, 2026 NA

Karwar - Karnataka

Tender For provision of loop line 1 and 2 with 60 kg rails and 60kg sleepers by laying and linking of track at sarzora station yard under sse/p-way/madgaon section over konkan railway in goa state (comp no 67302)

Rails Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

State Government

Central Government/Public Sector

Central Government / Public Sector

Central Government / Public Sector

State Government