Get complete information related to latest Rebar Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Rebar Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Rebar Tenders.
Tender For e-tender for material required for construction work--name & description of material, iron rebar 6,10,12 mm isi a iron articles gate, door, signboard, ventilation, etc., aj hook for fencing in kg, winding wire in kg
Tender For supply of vacuum contactor 400 amps 3.3kv part no. ht200 , vacuum contactor closing coil 110v dc part no. ht203 , vacuum contactor holding coil 110v dc part no. ht204 , p. t. 40va part no. ht206 , auxiliary contactor part no. ht208 , resin cast pt 300va 3.3kv by 110v 3 phase part no. 350 or ht350 , e.l.unit complete without transformer part no. 800 or ht800 , power hrc fuse part no. ht1500 , brass cable gland complete with c.i clamp stud part no. 1600 or ht1600 , static type relay part no. ht900a , pilot relay 12dc part no. ht2200 , contactor part no. ht200a , diode by255 for vacuum contactor part no. ht200c , vacuum contactor rectifier bridge part no. ht201 , copper terminal bar part no. 701 or ht701 , terminal chamber for i by c t by g o by g and partition part no. 1600b or ht1600b , auxiliary switch for vacuum contactor 2no and 2nc part no. ht205 , resin cast part no. ht300 , ht control fuse 3.3kv 2amps part no. ht400 , resin cast moulded cbct part no. ht500 , resin cast part no. ht650 , dmc moulded 3.3kv insulator for power fuse part no. ht700 , hrc fuse base and carrier for control part no. ht1200 , hrc fuse part no. ht1201 , lamp holder part no. ht1400 , cable box complete w o gland for i by c t by g oby g and partition part no. 1600a or ht1600a , isolator handle on off with axel bush part no. 1501 or ht1501 , copper bus bar 400 amps set of 3 part no. ht101 , relay part no. ht900e , isolator limit switch part no. ht1700 , isolator part no. ht100b , 72 sq mm ammeter suppressed scale part no. 1000 or ht1000 , ammeter selector switch part no. 1001 or ht1001 , single phase preventer cup 20 part no. 2001 or ht2001 , 72 sq mm voltmeter 0 to 5 kv by 110 volt part no. 1100 or ht1100 , resin cast part no. ht600 , push button with element for start stop test and reset part no. 1300 or ht1300 //bid details 2 / 29
Tender For supply of servo motor control valve, running time meter, 1-4 mxpu4 elbow, frp filter od 137, solenoid valve, sampling cock, seal ring, filter and permeate pump casing, o ring, shaft seal, casing p-1, i b bearing p-16, o.b. bearing p-18a, circlip internal p-18b, oil level viewer p-19d, bearing lock out p-22, o-ring bearing housing p-33b, deflector p-40, breather p-45, lip seal i.b. p-47, lip seal o.b. p-49, mech seal p-60, bearing lock washer p-69, cover gasket p-73, bolts p-171d, foot bolt p-171g, flexible hose h.p.feed inlet, chi 2-40 shaft seal, pressure tube 1000l, pressure switch, bearing ring p- 47a, spacing pipe -p - 64.c, slotted nut p - 67, pump head for pump p-2, stay bolt for pump p - 26, chamber complete p - 4, neck ring p - 45, neck ring retainer, chamber with bearing ring p - 4a, spacing pipe - p - 64.a, wear part kit - repair kit, ball bearing d244 p153, ball bearing p- 154, shaft pin p-10, chamber, o-ring 16.3 od x 2.4 thk, o-ring 137.5 od x 3.3 thk, chamber complete, chamber, neck ring, neck ring retainer, bearing ring, spacing pipe 17.52l, spacing pipe 4.50l, washer, 8.20id x 13.50od, shaft seal, impeller, shaftseal p-105, ball bearing p-153, anode plug, rod connecting assy, plug for priming, spacer v-packing p-157, o ring over hauling kit, piston set, retainer set, seal kit, seal ring, charging screw, charging plug screw, head distributor 3-4 air connection, o ring for head distributor assembly, cartridge filter housing, cartridge filter head, o ring hydraulic disc, solenoide valve actuator, 3 way ball valve, hp straight conn .3-4 for smcv, connector 1 1-4 bsp f x 1 1-4 vivt, vict end connector 1 , module bypass nozzle, victaulic couplings 1 1-4, victualic coupling 1. 1-2, coupler for vict. coup.1, victualic couplers 1. 1-2, permeate male elbow, smcv spindle seat, smcv valve unit for 3-4 valve, smcv valve spindle unit, servo motor control valve, solenoid valve 3-8 f 2-way ve83, solenoid valve actuator, ball v/v brass 1-4 bspf chrome plated, compressed air regulator, control cabinet ro 1530, door stay for cabinet, circuit breaker 1.6-2.5amp, circuit breaker 1.6-2.5 amp, thermister over load relay, single phase protector, hrc fuse 2 amp, hrc fuse 25 a, hrc fuse-bs-3nw 415vac 32 amp, main control switch 63a, potention meter, running hour meter, pressure gauge 0-10 bar, pressure transmitter, hand conductivity meter, flow meter feed, flow switch, sand filetr bracket, lp hose 32mm, hp line pressure gauge pi 61 hp pump discharge, hp hose 3-8id 1 2unfmx1 2unffx800l, high pressure hose module outlet, hp hose of module in, hp hose 1 idx1-vicx1500l saf 2507, lp hose hp pump inlet, pulley for motor 2 groove, pulley for pump 2 groove, seal kit, ho pump seat kit, taper bush 1610 20 mm bore, taper bush for motor pulley, wedge belt, av mount akcc 85m, av-mount between main frame and hp pumpbase frame, hp pump crank case oil, allen key set, socket dt module, belt spanner, jubilee clips for d 25, membrane cleaner 22, membrane cleaner 55, h.p connection - feed-brine, high pressure transmitter 4 to 20 ma pt60, high pressure manifold 6 x 1, rubber hose from c-f outlet to hp pump inlet 20-30tpd, abs service kit ro 200-102, abs service kit - 40 tpd, e-spare kit ro 0510-510, filter pump motor bearing pump end , hp pump seal kit, hop pump valve kit, hose for pk-20 pump in-out, level switch
Tender For tender for supply of boqmt37 d d- philips head screw driver 100 mm long ti , screw driver 8 , ring spanner 16x17 mm f1-5120-001597 , wheel nut spanner & tommy bar complete , light extension inspection no 2 with 10 , seal front oil 32x47x6 , head assy cylinder , sensor water temperature , bush , cord set high tension , lamp assy fornt fog , cover fuse box
Tender For rear air suspension spares for leyland vehicles - procurement of rear air suspension spares for leyland vehicles, m.r. split bush for bsiii/bsiv- 620000000704/p2602005, shock absorber for bsiii/bsiv- 620000000560/f8817600/ 620000002913, spherilastic bush without pin for bsiii/bsiv -620000000063/p2601405, spherilastic bush with pin for bsiii/bsiv-620000000790/p2602705, retaining plate for bsiii-620000000450/p2603130, leveling valve major kit for bsiii/bsiv -620000100205, levelling valve assembly for bsiii/bsiv -f8817700/620000100413, levelling valve lever for bsiii/bsiv-620000000309/p2600532, 30.48cm 12 clamp plate for bsiii/bsiv p2603230/620000000449, baloon to levelling valve hose-620000000286, m16x2x100 hexagon bolt for bsiii & bs iv -625000020069, m16 x 2 nylon nut for bsiii & bs iv-625000140015, m12x1.5 male elbow pressing fitting for bsiii / bs iv-620000001144, male connector m12x1.15 for bsiii & bs iv -620000001140, m16 x 1.5 male connector for bs iii -620000001142, rubber connector assembly for bs iii -620000100207, male connector m22 x 1.15 for bs iii -620000001143, m16 allen cap washer for bsiii/bsiv -625000230011/ 625000230042, 12 rolling diaphragm for bsiv -620000001386/g9280228bo/ 610000000088, 12 air spring assembly for bsiv -620000100132/g9280228ca, 12 steel piston for bsiv-620000002217, bump stop for bsiv -620000000269, allen bolt (m16 x 2 x 160mm) for bsiv -625000020080, bolt hex (16mm x 2mm x 120mm) for bsiv -625000020066, bolt hex (16mm x 2mm x 150mm) for bsiv -625000020128, nut hex(16mm x 2mm) for bsiv -625000140013, washer ms spring 16mm for bsiv -625000230006, m12 x 1.75 hex nut for bsiv -625000140009, union tee dia 6 for bsiv -620000001145, stud (12mm x 1.75mm x 65mm) for bsiv -620000000098, compound link assly for leyland bs iv vehicles-620000100041, m10 x 1.5 hex nut, m10 spring washer, m12 x 1.75 nylock nut, m12 plate washer, m12 rubber washer, tapper pivot spicot assly 6 holes-620000000821, taper pivot spigot for bsiv-620000000503, taper lpivot bolt assly for bsiv -620000100841, anti roll bar bush for ule vehicle-f0102300, rear air balloon for ule vehicles-p9200539, front air balloon for ule vehicles-p9400439, front bottom piston for ule vehicles-pb700019
Tender For providing and installation of children play equipments in municipal park near h.no.ru-335, ru block pitampura, ward no.57 under keshavpuram zone - providing and installation of children play equipments in municipal park near h.no.ru-335, ru block pitampura, ward no.57 under keshavpuram zone, supply and fixing of double arch swing.leg support :80 mm nb pipe. seat- anti skid rubber belt. bearing : heavy duty ball bearing. area : 6.0 m x 1.5 m. height : 2.6 m. top bar :50 mm nb pipe. suspension: 6 mm rubber coated chain. in this one child can enjoy the swing at one time. the arch shaped side frame shall be made of 80mm nb b class gi pipe shall be made up of 50mm nb b class gi pipe. the frame shall be powder coated to give an aesthetic look. the swing shall be made up of 10mm thick anti skid rubber top the rubber belt seat/ u shape swing seat with 2 eye bolt tyb-s06. made of polyurethane of size 53 x 20.5 x 20 shall be suspended on 6mm rubber coated gi chair. the bail bearings shall be mounted inside a specially designed nylon clamp. powder coating with pure polymer powder with 7 tank treatment 60 to 70 micron thickness. the holding down/fixing of equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size) (as per direction of officer in charge.), supply and fixing of toddler swing.the area :- 2.8m x 1.0m . in this toddler swing the center support shall be made up of 80 mm nb b class g.i. pipe. the horizontal bars shall be made up of 50 mm nb b class g.i. pipe. all gi pipes shall be powder coated. between the two horizontal bars there shall be a heavy-duty metal clamp attached to it. the bucket seats of the toddler swing shall be made of rubber with anti skid. the ball bearings shall be mounted inside specially designed nylon balls. the rubber seat shall be affixed on 8 mm thick gi chain. the seats shall be made with full care so that the child does not fall from it while swinging. powder coating with pure polymer powder with 7 tank treatment 60 to 70 micron thickness. the holding down/fixing of equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size) (as per direction of officer in charge.), supply and fixing of spiral slide. ladder-frame- 25m m n b pipe. handrail - 20 mm n b pipe. centre support- 50 mm n b pipe. area : 2.5 m x3.5 m. platform height : 2.1 m. chute f r p the topcoat is done using the best quality brand or duly powder coated. spiral slide shall be chute made of frp (fiber reinforced plastic / lldpe (low linear density poly ethyline) having thickness of 4mm slide center support shall be 80mm nb b lass gi pipe. landing module shall be supported by 20mm nb b class gi pipe. slide extension platform shall be made from frp / lldpe. the railing shall be made from 15mm nb and 20nn nb b class gi pipe. all pipes shall be coated with pure polymer powder with 7 tank treatment 60 to 70 micron thickness. the holding down/fixing of equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size) (as per direction of officer in charge.), supply and fixing of std. see sawhandle :-20 mm n b pipe. lever-32 mm n b pipe. colmun : 60 mm n b pipe. bearing : nylon bush press fitted. seats: frp seats with steel frame. the topcoat is duly powder coated. the level of see saw shall be made from 15, 20 and 25mm nb b class gi pipe. the seat of see saw shall be made from frp/lldpe. the stand and bush bearing made in 40mm nb b class gi pipe. see saw lever shall be welded to 5mm thickness ms plate for nut bolting with stand. all pipes flat shall be powder coated to avoid rusting. coating with pure polymer powder with 7 tank treatment 60 to 70 micron thickness. the holding down/fixing of equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)c37c40c41c39 (as per direction of officer
Tender For tender for supply of mt crv 40 c c - solenoid switch , filter head , fuel filter , fuel pipe , ball brg , fan belt , u bolt , fuel filter , spring , brake shoe , stablizer bush bar , csc assy , pilot brg , csc assy , cmc assy , clutch set , gear lever kit , combination switch , brake adjuster , handle