Latest srp unit Tenders | Government srp unit Tenders

Central Government/Public Sector

CTN :45263257

23 Jun, 2026 NA

Delhi - Delhi

Tender For supply of uhv deposition chamber - uhv chamber specification (vacuum better than 2 10-9 mbar uhv) chamber overview spherical (diameter 14 ) or equivalent square shaped uhv chamber with support frame equipped with three (3) x 2-inch magnetron sputtering sources. all cf flanges and uhv viewports/ss blanks, three (3) x 2-inch magnetron sputtering sources. each sputtering source has an individual gas inlet line for process gases. all cf flanges., substrate holder : diameter: 2 inches; heating molybdenum heater capable of heating substrate (a) from room temperature (rt) to 800 c during rotation and (b) from room temperature to 1000 c without rotation. rotation: substrate holder can rotate continuously, driven by a stepper motor. variable speed from 0 to 10 rpmmovement: up / down vertical movement of total 25mm to adjust substrate position during deposition sputtering geometry: one sputtering source mounted parallel to the substrate surface, tilt adjustable. two sputtering sources mounted confocally at an angle relative to the substrate. base pressure: lower than 2 10 mbar (ultra-high vacuum)., vacuum pumping system: turbo molecular pump: pfeiffer hipace300 / edwards next 300 / leybold turbovac 350i with cf100 flange or equivalent with integrated controller, ion pump with controller: included to maintain uhv vacuum levels and provide clean pumping., backing pump: pfeiffer hiscroll 12 / edwards nxds 15i / leybold scroll vac 15 plus or equivalent dry scroll pump used to back tmp, gate valves : one cf100 and one cf150 manual gate valves for isolating the chamber from the pumping systems as well as throttling, vacuum gauges and measurement: one cold cathode gauge with readout capable of measuring vacuum pressures down to1 10-10 mbar for precise uhv monitoring., one capacitance manometer gauge with measurement range from 1 10-1 to 1 10 mbar for accurate pressure reading during deposition phase, gas delivery system: two independent mass flow controllers (mfcs):a. one mfc (0-100 sccm) for argon gas feeding to all three sputtering sources via high vacuum valves.b. one mfc (0-100 sccm) for nitrogen gas feeding directly into the chamber with its own high vacuum valve.gas lines for ar and n2 are physically separated to avoid cross-contamination., chamber access and viewports: 1. two view ports installed on the chamber, each equipped with manual shutters. 2. access ports for gauges, pump, gas inlet and few spares for future upgradation., baking capability: entire chamber designed to bake-out at 150 c to reduce contamination and out gassing during operation, cooling capability : water manifold with flow switch / flow meters, near uhv chamber specification: chamber overview: spherical (diameter 14 ) or equivalent square shaped uhv chamber with stand., three 2-inch magnetron sputtering sources, each with individual gas inlet. all cf flanges and uhv viewports/ss blanks., substrate holder: a. diameter: 2inches; heating : molybdenum heater capable of heating substrate (a) from room temperature (rt) to 800 c during rotation and (b) from room temperature (rt) to 1000 c without rotation b. rotation : substrate holder driven by stepper motor. variable speed from 0 to10 rpmmovement: up / down vertical movement of total 25mm to adjust substrate position during deposition sputtering geometry: one sputtering source mounted parallel to substrate surface (tilt able preferred). two sputtering sources mounted confocally at an angle. base pressure : lower than 5 10 mbar (near uhv)., vacuum pumping system: turbo molecular pump : pfeiffer hipace 700 / edwards next 730 / leybold turbo vac 900 ix or equivalent with cf100 flange and integrated controller, suitable for near uhv vacuum., backing pump: pfeiffer hi scroll 12/edwards nxds15i / leybold scroll vac 15 plus or equivalent dry scroll pump used to back tmp, gate valves: one cf150 manual gate valve to isolate / throttle chamber from pumping system, vacuum gauges and measurement: cold cathode readout capable of dis

Central Government/Public Sector

CTN :45329483

17 Jun, 2026 12.61 Lacs

Nagrota - Himachal Pradesh

Tender For provision of 01 x 30 kva genr with connected items as standby power requirements for sewage treatment plant under age (i) bhalra - supply, installing, commissioning and testing, water cooled, sound proof silent type, turbo charged, diesel engine driven generating set 30 kva (at 0.8 pf), 415v, 3 phase, 4 wire engine as per is: 10001/10002 and alterator as per is: 13364, complete with relay panel for automatic starting on mains failure, control panels having meters in an integral acoustic enclosure as per recommendation cpcb norms, comprising of the following:notes: quoted rates shall deemed to include the following also:-(i) supply of t and p and normal space ie., bi-hexagonal ring spanner set of 12 pieces - 01 set.(ii) fuel measuement gauge - 01 no, hand operated fuel lifting pump with steel pipe 40mm dia - 01 no, hydro meter - 01 no, set of fan belt, oil/ fuel filters initial filling of coolant (coolant-2liters).(iii) service maintenance manual along with cat part list and price list - 03 set each.(iv) make of engine and alternator will be got approved from age (i) bhalra before placing the order., (a) diesel engine. diesel engine developing suitable bhp, 1500 rpm inclusive of the following standard accessories:(i) radiator/ heat exchanger cooling system. (xiv) battery charging generator.(ii) spider coupling guard. (xv) industrial silencer.(iii) fly wheel. (xvi) lubricant oil cooler.(iv) fly wheel housing complete with starter gear ring and coupling. (xvii) flexible pipe for silencer. (v) fuel pipes. (xviii) battery volt meter.(vi) air cleaner. (xix) water temperature gauge, lub oil pressure (vii) fuel and lubricant oil filter. gauge.(viii) by pass filter. (xx) speedo meter and engine running hours meter.(ix) coolant inhibitor. (xxi) display for fault.(x) fuel pump. (xxii) turbo charger.(xi) water pump. (xii) lubricant oil pump.(xiii) self/electric starter.(b) alternator : synchronous alternator 3 phase 4 wire, 50 cycles 1500 rpm, self excited, self regulated, brushless type, 0.8 pf, 415v, ac supply, 30 kva capacity, copper wound, complete including necessary tools, mounted on strong rigid steel fabricated base frame and directly coupled through flexible coupling with diesel engine, complete all as specified and directed., (c) amf/ control panel : amf panel factory made of suitable capacity as per original equipment manufacturer make and specification or as approved by oem for dg set of capacity 30 kva of suitable size, indoor cubical type, front and back openable fabricated out of mild steel sheet 1.6mm thick grounted in floor with adequate pcc foundation and minimum consisting of following :(i) contactor of suitable size for 30 kva dg set.(ii) copper bus bar of suitable current rating and sensitivity relay set unit with auxiliary cts.(iii) electronic latch circuit with tripping indication.(iv) re-set facilities.(v) 3 phase mvr relay unit with single phase protection complete with 2 no nc auxiliary contacts.(vi) 3 phase avr relay unit complete.(vii) self sequential starting relay unit 12 volts dc complete with alarm and power contactor. (viii) electronic timer 220 volts for main contactor with 1 no nc auxiliary contactor.(ix) electronic timer 220 volts for fuel cut off operation with 1 no auxiliary contactor.(x) battery charging 2x12 volts 10 amp complete with digital voltmeter and amps meter, including trickle and boost charging, make : su-kam, amco, exide or any other make as recommended by the manufacturer.(xi) volt meter 0-500 volts panel mounting of size 96mm square with selector switch digital type.(xii) amps meter 0-100 amps with 3 nos cts, 400/5 and selector switch 96 mm square digital type.(xiii) frequency meter (45-55) hz, 415 volt, 96mm square digital type.(xiv) the amf panel should have manual by pass arrangement too in case of failure of amf panel., (d) fuel tank of capacity as per manufacturer recommendations.(e) base frame made out of suitable channel duly reinforced and provided with adequate numbers of anti

CTN :45333094

16 Jun, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For tender for supply of gasket kit , o-ring for set w5 , end plate , o-ring , stud , bearing angular contact roller , first plate , o ring 26 x 2.5 mmn 294 , o-ring , o-ring , seal oil , exh pipe bellows , contam indicator , fuel filter , o ring , gasket , cover for solars , clamp , 0-2200 1/min tachometer , corrosion inhibitor conc. coolant cs100 , gasket , spare part kit for fuel filter , oil filter (element) , 0-2400 tachometer , o-ring , washer a 16 , o-ring 60x4 for set w5 , gasket , bolt hex gal cu 5 bk , panel , diaphragm , diaphgarm , insert (crank case breather) , actuating cylinder , bush , isolator 60 sh rd314b , plug in board , nut , intercooler(a bank) , exhaust bellow , valve , sealing ring , o ring , bolt adjusting , valve exhaust std floating bridge , push rod , gasket for set w5 , stud , gasket , sealing ring for set w5 , cylinder head complete , oil separator , seal ring , pan2-01 panel , ring seal asm , shield heat turbo , flow restric valve , paper pack centrifugal spinner filter , o-ring 11.3x2.2 for set w6 , axial bearing , tester , o-ring , control lever ros 2-05/fpp , panel , pan1-01 panel , gasket kit , sealing ring for set w6 , panel , air starter , bearing body , seal oil 48x72x8 mnn386 , seawater pump , washer , coolant pump high-temp circuit , nut , washer , odr 2-02 computer , clamp , y-gasket vib.damper , mpc1-01 computer , end plate , air filter , rubber bellows , gasket for set w5 , gasket for set w5 , hylomer sq 32m , rubber bellows , coupling , o ring , end plate , connector , conical spr. washer , base complete , rubber bellows (s s 0002035083) , clamp , turbine wheel , tube injector , arm rocker intake , swing foll , trust member , cylinder , disc , compensating washer , washer , screw , cylinder head , injector , water pump high temp circuit , exhaust turbocharger lift side , cylinder head complete , servo-locker , plug - in board , wiring harness for on-engine sensor , shaft

CTN :45223907

30 May, 2026 NA

Jammu - Jammu And Kashmir

Tender For corrigendum : supply of clutch master cyl assy , set of brake lining , hose air cleaner to turbo charger , water pump assy , saloon out side mirror , wiper blade , wiper arm pentogroph , wiper blade assy 508 mm , wheel bolt m 22 x 15 , oil seal rear hub , dikki assy , cartridge lub oil filter , belt v ribbed 1422 , rubber hose , tempe transducer , height marker lamp red , hold relay , battery cut off switch , side window glass , assy clutch master cyl

CTN :45346989

06 Jun, 2026 45.0 Thousand

Gwalior - Madhya Pradesh

Tender For supply of head light assy rh , disc pad , assy water pump , front hub bearing , bearing , turbo charger core assy , field coil assy , battery cut off switch , assy fuel water seperator

CTN :45307364

03 Jun, 2026 1.00 Lacs

Gurdaspur - Punjab

Tender For supply of fuel feed pump , assy exhaust pipe , assy oil filter , exhaust pipe turbo to exn brake , brake switch relay 24v , major repair kit , oil seal , stainer sediment , handle door , assy cable complete , brg taper roller , clutch release brg , bearing , shoe set rear brake

CTN :45302762

02 Jun, 2026 NA

Bathinda - Punjab

Tender For supply of scroll compressor , assy turbo charger , end steering tie rod , combination switch , chain sprocket kit , air filter element , change over switch , fuel pre filter , assy fuel filter , brush gear assy , assy steering pump , pump assy fuel , controller assy epi , circuit braker

CTN :45213517

08 Jun, 2026 NA

Bathinda - Punjab

Tender For corrigendum : supply of assy egr , kit pad assy , assy turbo charger , front windshield glass , rear windshield glass , assy fuel filler lid , belt v ribbed , cross assy , universal joint assy , repair kit frt spring brake actuator , repair kit spring brake actuator , assy steering pump , brush gear assy

Central Government/Public Sector

CTN :45291823

12 Jun, 2026 1.45 Lacs

Sunderbani - Jammu And Kashmir

Tender For supply of liner cylinder std , seal o ring liner , bush cam shaft , bearing crank shaft 0 10 , bearing connecting rod 0 20 , piston with pin with lock , piston ring std , thrust washer upper std , thrust washer lower std , bush connecting rod u b , rod and cap assy connecting rod with bolt and nut , pin dowel block , engine overhauling gasket set complete , valve air intake , valve exhaust , seal valve stem , valve seat , valve guide , seal oil crank shaft rear , seal o ring spacer , seal oil crank shaft front , bolt fan , bearing fly wheel , belt drive fan belt , filter assembly secondary for turbo charger , filter assy engine oil , tap and screen assy fuel fuel tank , disc clutch pto , disc clutch main , kit fuel filter primary and secondary , gasket oil sump , gasket fip ear inspection plate , gasket water pump , gasket crank shaft rear oil seal , gasket timing gear housing , gasket timing gear cover , gasket cylinder head , gasket cylinder head cover , gasket air intake manifold , filter assy hydraulic lift oil intake , seal o ring hydraulic , clamp radiator upper , seal o ring , seal benjo washer , u j cross propeller shaft , yoke propeller shaft , bush pin swivel housing upper front axle , bearing sp herical lower , pin swivel housing upper wing pin post , seal o ring front axle , seal oil half axle shaft 4wd front axle , seal wheel housing 4wd front axle , tie rod end , cylinder assy power steering pipe inner and outer , clamp assy house , gasket water outlet , ring thermostat sealing , gasket exhaust manifold , hose assy fuel filter to fip pump , hose assy fuel feed pump to fuel filter , gasket hydraulic pump , hydraulic oil filter , gasket turbo charger oil outlet , pipe metal power steering to inter oil , pipe metal hydraulic pump , jubilee clip half inch , benjo washer copper all size , benjo bolt 19 no , benjo bolt 17 no , bolt and nut 10 no , bolt and nut 12 no , bolt and nut 14 no , valve grinding stick , seal oil gear box , gasket egr valve , injector fuel return pipe rubber , gasket fuel tank , gasket turbo charger to adopter , stopper cable , temperature sending unit , oil pressure sending unit , front indicator sparking light assy , back light assy , insulation tape , 0 to 20 no size writing brush short hair , 0 to 20 no size writing brush long hair //bid details 2 / 64

Central Government/Public Sector

CTN :45303026

13 Jun, 2026 95.0 Thousand

Sunderbani - Jammu And Kashmir

Tender For supply of seal o ring liner , gasket engine oil sump , gasket egr valve , gasket turbo charger oil outlet , gasket turbo charger to adopter ggo , washer 20 point 5 aluminum sealing adapter , rod valve push rod e 3 , seal oil crankshaft , gasket fip gear inspection cover , spacer crank pully , seal o ring spacer , bolt water fan , gasket water pump , bearing 620322 fly wheel , seal oil crank shaft rear , gasket crank shaft rear , belt drwe fan belt , gasket hydraulic pump , filter assy second dry for turbo charger , filter assy engine lube oil , injector fuel return pipe , fuel filter primary and secondary , gasket fuel tank , gasket cylinder head , gasket air intake manifold , gasket exhaust manifold , gasket cylinder head cover , circlip piston pin , bearing connecting rod , gasket tube rocker cover , seal valve stem , gasket muffler assy , ring thermostat sealing , thermostat valve , gasket water outlet , seal o ring hub front axle , seal oil half shaft front axle , seal wheel housing front axle , tie rod end rh and lh , bush pin swevel housing upper , bearing sp herical king pin , pin upper king pin post , disc clutch pto , disc clutch main drive , kit crank shaft main bearing , kit thrust washer , filter assy hydraulic lift oil intake , seal o ring , gasket timing cover , seal oil crank shaft front , gasket timing gear housing , kit piston ring set ft 6065 , hydraulic filter , banjo washer copper all size 01 pkt , brake pedal spring , water separator filter , oil cooler pipe rubber , pin sleeves brake pedal pin , bracket and mounting lh , bracket and mounting rh , pin safety split , jubilee clip 1 inch , bolt and nut 12 no one into half inch , valve grinding stick , self solenoid switch 12 volt , back light assy lis , insulation tape , l t wire 3 mm , meter bulb tube type , self copper bush , plastic paper , horn assy ) /bid number : gem/2026/b/7577170 * /dated: 23-05-2026 & & / bid document 1 / 52

Srp Unit Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector