Tender For supply of suction timing belt v 87.44.525.0 , suction timing belt v 87.44.524.0 , guide plate v 65.56.096.0 , disc spring ext.dia. 67,5 d 0.626.024 , shim ring 40x50x1 mm k 1.46.675 , support cartridge v 45.01.870.0 , disc spring v 45.89.012.0 , suction timing belt v 87.44.556.0 , suction timing belt v 87.44.557.0 , folding device l 581.03.6520.0 , folding device l 581.03.6521.0 , roller carriage l 581.00.7620.0 , disc spring ext.dia. 50.0 d 0.621.019 , linear guide k 1.388.10 , tightening shaft l 581.03.3003.0 , upper guide v 79.03.427.0 , plate cylinder l 581.00.2038.0 , abjustment spindle l 581.00.3518.1 , axial adjusting device l 581.00.3514.1 , bushing v 25.15.564.1 , clamping ring v 45.97.217.0 , helical spur gear r 2.20.060.477 , spur gear r 1.20.044.456 , needle bearing rna 4907 2rs k 1.315.87 , snap ring for bore d 55 mm k 1.45.055 , impression cyl outsideprint v45.41.043.0 , one way drive k1.960.99 , ink pump k 2.156.20 , diaphragm k 2.149.13 , eccentric bushing v 27.89.238.1 , duct roller v37.70.977.0 , retaining ring for shaft k 1.40.030 , toothed segment v 45.26.170.0 , ratchet wheel v 45.36.051.0 , supporting bushing v 27.17.628.0 , bushing v 27.45.920.0 , pneumatic cyl type av 50 10 k 2.410.03 , duct roller s 581.02.0064.0 , eccentric bushing v27.89.234.1 , eccentric bushing v27.89.235.1 , adhesive circulationpump l 581.00.8347.3 , diaphragm valve k 3.374.03 , roller carriage l 990.00.0405.3 , roller carriage l 990.00.0405.4 , disc spring v 45.89.023.0 , holding down device v 87.44.011.0 , longitudinal scoring knife v 03.00.039.0 , rubber roll 30 by 51w 135mm l581.00.2532.0 , cros scoring knive19.3x3,355v03.01.408.1 , counter roler cross scoring v45.83.034.0 , stock spring power k 2.963.02 , stepping motor k 6.692.56 , transport belt conveyor v 87.33.812.0 , curved gearcoupling k 1.941.36 , hmi of 191 splicer unit duly programmed , product separator l581.03.7500 , hebel lever part no v 55.07.163.0 , hebel lever part no s 581.03.0097.0 , transmission belt v 87.44.519.0 , transmission belt v.87.44.523.0 , transmission belt v.87.44.522.0 , disc spring v 45.89.025.0 , transport disc v 29.65.024.0 , stop v 67.70.290.0 , suction bar v 87.91.035.1 , clamping ring v 69.08.878.0 , counter pressure roller l380.00.0137.1 , upper knife v 03.02.566.0 , setting gauge v 45.29.523.0 , rubber roll l380.00.2537.0 , one way drive k 1.960.63 , flat belt thermo m15989 v 87.43.730.0 , lower knife part no v.03.02.163.1 , pulling roller v 37.61.279.0 , rubber roll 45 by 80 45mm l380.00.2556.1 , rubber roll 19by30 13mm n010.022 , transport roll v 25.05.934.0 , tube v 25.05.935.0 , segment roller v 29.80.688.0 , turning bar v 35.05.960.0
Tender For supply of guide rail lines for battery transport trolley which are mounted on hardwood beam with guide plates and clamping pieces , battery transport trolley with four sprocket wheels supported on grooved ball bearings with two wood supports , longitudinal transport trolley two u profiled sections and two l profiled sections with rollers supported on pins and grooved ball bearings , battery lifting trolley with locking system , extension lifting pins with locking system big and small length , battery lifting wheel with pendulum , transverse transport trolley chassis with two sections along with locked hexagon screw bolt and grooved ball bearings and axial grooved ball bearings lifting weight , transverse transport trolley chassis overhead side wheels , support side plates with roller bearings , support plates connecting rods , lifting support or slide with support arms , hydraulic pump unit , hydraulic cylinder or ramp , bottom plate for hydraulic motor fixing , pneumatic chain blocks , battery stands for removal and fixing of hook rails , battery lifting plates , safety mesh for battery lifting ) /bid number: gem/2026/b/7121518 * /dated: 09-03-2026 & & / bid document1 / 19
Tender For manufacture and supply of curved thick web switchexpansionjoint (twsej)as per rdso's drg. no.t-8822 (alt-2). { all conditions applicable as per rdso'sletter no. ct/jw/3/curved twsej dt. 04.06.2025}. list of fittings as per rdso'sdrg. no.: t-8822 (alt-2) excluding erc mk v and psc sleeper. (the alt indrawings and specifications issued by rdso up to one month prior to tenderclosing date shall be applicable in this tender) 1. (1.0to 2.5 degree) curved thick web sej , 60 kg, rdso drg. no. t-8822 = 05 sets2. (2.5 to 4.0 degree) curved thick web sej , 60 kg, rdso drg. no. t-8822 =05 sets