Latest thermocouple probe Tenders | Government thermocouple probe Tenders

CTN :45696133

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45697599

04 Jul, 2026 10.02 Lacs

Multi City - Andhra Pradesh

Tender For dismantling and replacement of new / repaired p.f bends / elbows and reversing of orifices for pf piping of units-3&4 during overhaul period for the year 2026-27.

State Government

CTN :45187417

30 Jun, 2026 NA

Multi City - Chhattisgarh

Tender For corrigendum : procurment of different size of ceramic lined coal pipe orifices for xrp-1003 mill at 2x500 mw, abvtps, marwa

CTN :45517156

11 Jul, 2026 NA

Hyderabad-T - Telangana

Tender For supply of orifices in ss304 material as per astm a276

CTN :45430786

18 Jun, 2026 NA

Ariyalur - Tamil Nadu

Tender For supply of electronics andcommunication engineering lab materials - electronics and communication engineering lab materials, dso (digital storage oscilloscope)bandwidth: 50 - 100 mhz.sampling rate: 1gs/s.channels: 2 (minimum)power supply: 100v 240v ac, 50-60 hzautomatic measurement: vpp, vavg,rms, frequency, period, vmax, vmin, rise time, fall time, + width, - width, +duty, - duty etc.,horizontal scale: 5 ns/div 100 ns/div or equivalentvertical resolution: 8 bits (2 channels simultaneously)vertical sensitivity: 1 mv/div 10 v/div (at input)waveform math: +, -, x , , invert, fft etc.,waveform storage: 16 waveforms or equivalentcommunication interface: usb host, usb interface.7-inch color display or equivalentbasic trigger functions, digital ic trainer kit with breadboard5v dc, 1a regulated power supply 12v dc / 15v, 200 ma regulated power supplysolderless breadboard to accommodate 8 16-pin icszif (zero insertion force) ic socketssupports ttl and cmos icslogic io leds for output monitoring8 buffered led outputs8 debounced switch inputsttl clock: 1 mhzvariable clock generator: 0.5 hz to 50 hzsingle pulse output: 100 ms (buffered, positive and negative outputs)one seven-segment display with 4 bcd inputsbuilt-in logic probesbuilt-in logic switchesexperiments on basic logic gates, flip-flops, counters, and multiplexers, eliminator transformer (stepdown)input - 220v - 240v ac, 50 hz, output-2v to 12v dc, 0-2 a ripple: 5mv, decade resistance boxrange: 1 to 10 m , steps: 1-10-100-1k-10k, accuracy 1%, suitable for filter and oscillator experiments, decade inductance boxrange: 1 h to 10 h, rotary switch selection, low loss inductors, accuracy 1%, , suitable for filter and oscillator experiments, 8051 micro controller kitoperating voltage: +5v dc4 kb flash (at89c51) / 8 kb flash (at89s52)ram: 128 bytes internal ram16 2 alphanumeric lcdpush buttons / tactile switchesdip switches for digital inputinbuilt adc interface : ldr,potinbuilt dac interfaceinbuilt stepper motor driver with stepper motorinbuilt dc motor driver with dc motor1x4 led array, 1 x4 keypad, 1x relay1x buzzer, 16x2 lcd display, 1x pwm driver1x hardware interrupt key, inbuilt rtcinbuilt eeprom, inbuilt uart module4x7 segment display, both assembly and c language programmable, pc interfaceable., single phase induction motorsingle phase induction motor, 230v ac, 50hz supply.power rating 1 hp (0.75 kw).speed 1440 rpm.capacitor start/run type suitable for lab useloading setup portable ammeter and digital tactometer contact type, auto transformerinput - single-phase, 230v/240v, 50 hz, 4a, ac output - 0 to 270vac, class "h" or class f insulation., temperature measurement kitsensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc).display: 3 digit led/lcd digital display (typically 200mv fsd).temperature source: portable water kettle or heater block.signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation. test points: multiple 2mm/4mm banana sockets for monitoring input/output signals.power supply: 230v ac, 50hz, single-phase.accessories: includes a glass thermometer, ntc thermistor probe 10k, k-type thermocouple probe, patch cords, and instruction manual., ask modulation and demodulation kitmessage signal 1 : 8 bit variable data, amplitude 5vmessage signal 2 : debounce data, amplitude low (0) & high (5v)message signal 3 :fixed data 25k, 12.5k, 6.25k, 3.12k, amplitude 5vcarrier signal : sine wave frequency 200 khz, amplitude 5vmodulator type : switching icdemodulator : envelope detector & lpfcomparator : lm 311 basedsupply voltage (board) : +12v, +5v / dcsupply current : 100 ma (minimum)input voltage : 230 v/ 50 hz acinterface connectors : 2mm banana socket, dth trainer kitpower supply 200v to 240v ac, 50hz,dish antenna 1.5 aluminum steerable, lnb low noise block down converterinput frequency ku band.output frequency 950 to 1450 mhz.conversion gain 65 db.noise temp 35 degree k max.set top box receiver in traine

CTN :45432718

25 Jun, 2026 NA

Mahendragiri - Tamil Nadu

Tender For supply of supply of special t - type thermocouple probe (dual element & dual output configuration)

CTN :45404144

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45386617

06 Jun, 2026 NA

Vellore - Tamil Nadu

Tender For ece lab items dept use - eliminator transformer (step-down) kitinput - 220v - 240v ac, 50 hz, output-2v to 12v dc, 0-2 a ripple: 5mv, strain gauge trainer kitmetal foil strain gauge mounted on beam/cantilever strain measurement under applied load wheatstone bridge arrangementsignal conditioning and amplification circuitinstrumentation amplifiers, 3 digit display of strain / output voltage zero and gain adjustment controlsprovision for applying calibrated loads regulated power supply, 230 v ac, 50 hz table-top trainer with labeled paneltest points to measure the signalsbuilt in power supplies and wooden closed cabinet supplied with patch cords and experiment manual, temperature measurement kitsensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc).display: 3 digit led/lcd digital display (typically 200mv fsd). temperature source: portable water kettle or heater block.signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation.test points: multiple 2mm/4mm banana sockets for monitoring input/output signals.power supply: 230v ac, 50hz, single-phase.accessories: includes a glass thermometer, ntc thermistor probe 10k, k-type thermocouple probe, patch cords, and instruction manual., sim reader trainer kitsim compatibility supports 2g 3g 4g lte sim cards,sim reader mode: reading writing gsm sim card data, imsi, ki codes, phonebook interface usb 2.0 or rs 232 serial port for pc communication.clock frequencies: selectable frequencies 3.579 mhz, 7.159 mhz, 14.318 mhz for sim card operation.power supply: onboard smps 12v 2a or 5v dc with overload protection. hardware components:6-pin or 8 pin sim card socket.led indicators for power, sim reset, and data activity.optional lcd 128x64 and keypad 20 keys for standalone operation. software tools support for at commands gsm etsi 07.0707.05, sim manager utilities, and data logger functionality. common trainer kit featuresfault simulation ability to create faults e.g., sim not detected, vcc failure for troubleshooting.test points: multiple test points e.g., 55 nos for observing signals sim rst, clk, i o via oscilloscope.construction tested glass epoxy pcb, often housed in a study educational case., dual output regulated dc variable power supplydual output regulated power supply- input voltage: 230v/50hzac- output voltage: (0 30v)dc- output current: (0 2a)dc- protection circuit: over voltage and over current protection, short-circuit protection- high efficiency: greater than 85%- low ripple and noise: less than 50 mv, lvdt sensor trainer kitac mains power supply : 230v 10%, 50hzfixed regulated dc power supply : +5v, 12v 500matransducer : lvdtlvdt displacement : 20mm (40mm total)displacement scale : linear 20mmdisplacement display (mm) : red color 3 digit led displayexcitation frequency : 4khzexcitation voltage : ac variable 5v, dc digital voltmeter - 3 digit led/lcd display, measurement range: 0 20 v dc, accuracy: class 0.5( 0.5 % full-scale), dc ammeter digital - 3 digit led/lcd display, measurement range: 0 5 a dc, accuracy: class 0.5 ( 0.5 % full-scale)

CTN :45365476

13 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For purchase of lab equipments for ece dept - purchase of lab equipments for ece dept, dc voltmeter (digital) (item code : c006) 1.dcvoltmeteranalog moving coil -(0-10)v, class1.0( 1%full- scale)accuracy - 5 nos2.dcvoltmeteranalog- movingcoil-(0-30)v, class1.0( 1%full-scale)accuracy - 4nos, dc ammeter(item code : c007)specifications: 1. dcammeteranalog movingcoil- (0-30)ma,. 5 nos2. dcammeteranalog -movingcoil -(0-1000) a, class 1.0 ( 1 % full-scale) accuracy - 5 nos, decade capacitance box(item code : c0011)specifications: range: 100 pf to 100 f rotary switch selection with 6 dials. maximum voltage: 350 v. accuracy: 1%., decade inductance box(item code : c0012specifications: range:10 hto10h. rotaryswitchselectionwith6dials. low-lossinductors. accuracy: 1%., 8051 microcontroller kit(item code : c0013)specifications: operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc2148) (item code : c0014)specifications: cpu - lpc2148, core - 16/32 bit arm7tdmi-s speed - max 60 mhz, flash - 512kb, ram (on chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converter with 14 analog inputs, one 10bit d/a converter, six pwm & watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay & buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, temperature measurement kit (item code : c0019)specifications: sensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc). display: 3 digit led/lcd digital display (typically 200 mv fsd). temperature source: portable water kettle or heater block. signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation. test points: multiple 2 mm / 4 mm banana sockets for monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntc thermistor probe, k-type thermocouple probe, patch cords and user manual., fpga trainer kit(item code : c0025)specifications: must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb uart bridge, usb cable. user manual.

CTN :45340402

04 Jun, 2026 NA

Theni - Tamil Nadu

Tender For purchase of non consumable item in hydraulic lab for civil department - bernoullis theorem apparatus(closed circuit)(code e001)bernoulli apparatus flow rate range up to ~20 l/min or more (depending on pump) pump power ~0.5 kw / -1 hp pressure measurement ~0 290 mm to 370 mm wc measuring tank 25 50 l utility 230 v ac, single phase, venturimeter and orifice meter apparatus (closed circuit)(code e002)orifice & mouthpiece apparatus set of orifices: usually 2 sizes (e.g., 8 mm, 10 mm) or more. set of mouthpieces: several l/d ratios (e.g., 10 mm dia with l/d 1, 2.5, 4). sump tank capacity: ~70 100 l. constant head tank: ~20 35 l. measuring tank: ~25 40 l with scale. pump: 0.5 hp monoblock / centrifugal pump (single phase). instrumentation: hook gauge / pointer gauge for head/jet measurement; stopwatch. power supply: 220 230 v ac, single phase., pipe friction apparatus (closed circuit) with all acceeories(code e003)pipe friction apparatus test pipe length ~1 m per pipepipe diameters 12 mm 25 mm (varies)sump tank capacity ~40 l 100 lvolumetric tank ~40 lpressure range (manometer) ~300 500 mm water / mercuryflow rate range 0 60 l/minpump 0.5 hp centrifugal, centrifugal pump testing rig with all accessories(code e004)single speed centrifugal pump testrig (closed circuit) (heavy duty)a. single speed stainless steel centrifugal (mono block) pump set of size 25mm a 1hp, 2880rpm, single phase 50 cycles, 200/220 volts ac electric motor. to discharge about 100lpm at 10 meters head at a single speed of 2880 rpmb. switch and dol starter for the above pump set and an energy meterc. piping system consisting of pipes, valves, and fittings with pressure and vacuum gauges (gi/pvc).fibreglass lined s.s. measuring tank of size 500x500x600mm height provided with a gauge glass, scale and adrainvalve. fibreglasslined s.s. sump of size 1500x500x300 mm height capacity rigid stainless steel frame work compactly fitted with all the above items as a self sufficient package, reciprocating pump testing rig(code e030)reciprocating pump apparatus type of pump single acting reciprocating pumpcylinder bore 50 80 mmstroke length 100 150 mmspeed 30 60 rpmdischarge 5 20 lpmsuction head up to 5 mdelivery head up to 20 mmotor power 0.5 1 hpmotor speed 1440 rpmpower supply 230 v ac, single phasepressure gauge range 0 5 kg/cm vacuum gauge range 0 760 mm hgmeasuring tank capacity 30 50 litersmaterial cast iron pump, ms framedrive belt drive / direct coupling, mouthpiece & orifice setup(code e002 )experiments : to determination of cd, cv, and cc of venturi meter.specificationsventuritype : acrylicsize/dimension : 350mm 350mm 600mmnominal size : 25 mmend connection : gi pipeusage/application : laboratorybody material :stainless steelorifice meterapparatusexperiments : to determination of cd, cv, and cc of orifices meter.specificationspump : hp centrifugal pump.ac motor : hp 230v ac.supply tank : 120 ltrs. made of ms with frp lining.measuring tank : 40 ltrs. made of ms with frp lining and fitted with piezo meter tube & scale.piping &fittings : gi/pvc with necessary valves.fitted with u-manometer with mercury.control panel : 1hp dol starter.digital timer : mcb load and line indicator.

Thermocouple Probe Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government