Get complete information related to latest Vaccum Gauge Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Vaccum Gauge Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Vaccum Gauge Tenders.
Tender For supply of forbes marshall wika make pressure gauge , forbes marshall wika make pressure gauge , forbes marshall wika make pressure gauge dial size , forbes marshall wika make pressure gauge dial size12 , forbes marshall wika make pressure gauge dial size , forbes marshall wika make pressure gauge dial size , phase tester make , forbes marshall wika make temprature gauge body ss , forbes marshall wika make temprature gauge body ss , forbes marshall wika make vaccume gauge dial size , ss compensation cable for temprature sensor with armoured cable , air filter regulater range , air pressure switch , ms connector , pu connector thread size , stripper and wire cutter , teflon tape od , forbes marshall wika make back mount gauge dial size , ms socket for gauge , forbes marshal wika l make pressure gauge dial size , duplex thermo couple k type stem thickness 8mm and stem lenth , toshaniwell make rtd for temprature 6 mm thickness stem lenth , thermo couple k type ss , temrature indicator rtd and thermo couple , digital milli volt milliamp source meters for calibration model lic , misibus make double chanel isolator input , selec make digital rpm meter with npn , selec make temrature controller , selec make pic 101n , vertical nrv for air compressor size , tank safty valve size , pressure gauge syphon tube maximum pressure , pressure gauge syphon tube maximum pressure , ss needle valve , ring spanner set 1808 double sided open end wrench pack of , adjustable spanner size , taparia make dep 08 double ended spanner set double sided open end wrench , brass valve for air compressor and control valve
Tender For tender for supply of dead weight pressure gauge callibrator range- 0 to 400 kgcm sq make-system engineers , vaccumgauge callibrator compression typerange 0 to 760 mmhg make system engineers , digital clamp meter make meco , digital multimeter make meco 27 , combination cutting pliertaparia make , bent nose plier taparia make inside 12 , bent nose plier taparia make outside , circlip nose plier taparia make inside , circlip nose plier taparia make out-side , line tester , taparia 813 , screw driver set taparia 812 , champion screw driver set , rubber hand gloves11 kv electrical , ring spanner set taparia make 06-32 mm , ring spanner taparia make , fix spanner set taparia make 06-32 mm , fix spanner taparia make , sockets spanner square drive set taparia , adjustable wrench with soft grip , pipe wrench taparia make , grinder machine , bosch make , air blower , bosch gbl 650 make gbl , allen key set , allen key , slogging ring spanner heavy duty , slogging fix spanner heavy duty , ring spanner taparia make , fix spanner taparia make , varnish elmo luft 1a golden , silica gel blue crystal , painting brush , measuring tape 03 mtrs 05 mtrs , bearing puller taparia make model bp 308
Tender For supply of adaptor for vaccumgauge head for perlite container , adaptor for vaccumgauge head for non perlite container , protection cover for vaccumgauge head , port cover for evacuation plug , valve cap for evacuation port
Tender For a r maintenance of shimla town from lwss gumma sh providing and fixing pressure gauges and vaccumgauges for all pump sets at gumma drabla old gumma gumma old double stage nauti khad pumping station
Tender For supply of uhv deposition chamber - uhv chamber specification (vacuum better than 2 10-9 mbar uhv) chamber overview spherical (diameter 14 ) or equivalent square shaped uhv chamber with support frame equipped with three (3) x 2-inch magnetron sputtering sources. all cf flanges and uhv viewports/ss blanks, three (3) x 2-inch magnetron sputtering sources. each sputtering source has an individual gas inlet line for process gases. all cf flanges., substrate holder : diameter: 2 inches; heating molybdenum heater capable of heating substrate (a) from room temperature (rt) to 800 c during rotation and (b) from room temperature to 1000 c without rotation. rotation: substrate holder can rotate continuously, driven by a stepper motor. variable speed from 0 to 10 rpmmovement: up / down vertical movement of total 25mm to adjust substrate position during deposition sputtering geometry: one sputtering source mounted parallel to the substrate surface, tilt adjustable. two sputtering sources mounted confocally at an angle relative to the substrate. base pressure: lower than 2 10 mbar (ultra-high vacuum)., vacuum pumping system: turbo molecular pump: pfeiffer hipace300 / edwards next 300 / leybold turbovac 350i with cf100 flange or equivalent with integrated controller, ion pump with controller: included to maintain uhv vacuum levels and provide clean pumping., backing pump: pfeiffer hiscroll 12 / edwards nxds 15i / leybold scroll vac 15 plus or equivalent dry scroll pump used to back tmp, gate valves : one cf100 and one cf150 manual gate valves for isolating the chamber from the pumping systems as well as throttling, vacuum gauges and measurement: one cold cathode gauge with readout capable of measuring vacuum pressures down to1 10-10 mbar for precise uhv monitoring., one capacitance manometer gauge with measurement range from 1 10-1 to 1 10 mbar for accurate pressure reading during deposition phase, gas delivery system: two independent mass flow controllers (mfcs):a. one mfc (0-100 sccm) for argon gas feeding to all three sputtering sources via high vacuum valves.b. one mfc (0-100 sccm) for nitrogen gas feeding directly into the chamber with its own high vacuum valve.gas lines for ar and n2 are physically separated to avoid cross-contamination., chamber access and viewports: 1. two view ports installed on the chamber, each equipped with manual shutters. 2. access ports for gauges, pump, gas inlet and few spares for future upgradation., baking capability: entire chamber designed to bake-out at 150 c to reduce contamination and out gassing during operation, cooling capability : water manifold with flow switch / flow meters, near uhv chamber specification: chamber overview: spherical (diameter 14 ) or equivalent square shaped uhv chamber with stand., three 2-inch magnetron sputtering sources, each with individual gas inlet. all cf flanges and uhv viewports/ss blanks., substrate holder: a. diameter: 2inches; heating : molybdenum heater capable of heating substrate (a) from room temperature (rt) to 800 c during rotation and (b) from room temperature (rt) to 1000 c without rotation b. rotation : substrate holder driven by stepper motor. variable speed from 0 to10 rpmmovement: up / down vertical movement of total 25mm to adjust substrate position during deposition sputtering geometry: one sputtering source mounted parallel to substrate surface (tilt able preferred). two sputtering sources mounted confocally at an angle. base pressure : lower than 5 10 mbar (near uhv)., vacuum pumping system: turbo molecular pump : pfeiffer hipace 700 / edwards next 730 / leybold turbo vac 900 ix or equivalent with cf100 flange and integrated controller, suitable for near uhv vacuum., backing pump: pfeiffer hi scroll 12/edwards nxds15i / leybold scroll vac 15 plus or equivalent dry scroll pump used to back tmp, gate valves: one cf150 manual gate valve to isolate / throttle chamber from pumping system, vacuum gauges and measurement: cold cathode readout capable of dis