Latest cable end box Tenders | Government cable end box Tenders

CTN :45048307

31 Jul, 2026 NA

Tarapur - Maharashtra

Tender For corrigendum : : supply, installation, testing & commissioning of electrical equipment for dg block 119a of inrp - ht panels (119a)supply, installation, testing & commissioning of indoor type floor mounted, single front, metal clad, 1250 a, 6.6 kv, 3 phase, 3 wire, vcb switchgear panel suitable for a short circuit current of 31.5 ka for 3 seconds, internally arc tested for 31.5 ka for 1 second, comprising of following incoming & outgoing feeders : incoming feeder: 1 no. 1250 a, 3p vcb outgoing feeders: i) 7 nos. 630 a, 3p vcbii) 1 no. 1250 a, 3p vcb as tie feederwith surge arrestors, relays, pts, cts & other necessary accessories including associated structural steel required for complete installation of the panel & equipment earthing of the panel from both the earthing terminals of the panel to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings. reference drg. nos: ip1/119a/05027339/dwg/001/r0 & ip1/119a/05027339/dwg/002/r0(note: terminal box of each incomer of 6.6kv switchboard shall be suitable for terminating 4x3cx400 sq.mm., 6.35/11kv (e), a2xwy cables.), supply of spares for ht panels as per attached spares list mentiond in section c, part ii of tender, 2.5 mva, 6.6/0.433 kv dry type transformers (119a)supply, installation, testing & commissioning of 6.6/0.433 kv, 2.5 mva, dyn11 dry type cast resin transformer having percentage impedance of 8.5% complete with ht cable end box, lt bus duct flange, off load tap changer on ht side with range of +/-5% in steps of 2.5%, wti scanner, ct for restricted earth fault protection and other necessary accessories including associated structural steel required for complete installation of the transformer & equipment & neutral earthing of the transformer from both the earthing terminals of the transformer to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings.reference drg. no. : ip1/119a/05034347/dwg/001/r0, supply of spares for dry type transformers as per attached spares list mentiond in section c, part ii of tender, 2000 kva diesel generator sets (119a)supply, installation, testing & commissioning of 3 phase 2000 kva prime power 433v, 50hz, 0.8 p.f. diesel-generator sets with 110% overload capacity for 1 hr with four (4) stroke inline or vee type cylinder arrangement having engine speed 1500 rpm, 24v electric battery starting system with a provision of interchangeability of battery bank between two dg sets, complete with all auxiliary equipment including amf control panel, auxiliary mcc panels, heat exchanger cooling system, raw water pump, remote radiator with fans on terrace, ms exhaust piping, exhaust structure (maximum 30 m stack), 4 nos. of 3.6 cubic metre fuel day tank outside dg building (for all 4 dg sets) & 1 no. of 990 ltr intermittent tank inside each dg room, ms "c" class fuel piping between engine & fuel tank, dg room accoustic treatment & complete ventilation of dg room, brushless excitation for alternator, one no. 3200 amp 415 v 4p acb, ms structural steel supports/ channels/ angles & other necessary accessories including associated structural steel required for complete installation of the dg & equipment & neutral earthing of the dg from both the earthing terminals of the dg to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & necessary statutory clearances from cpcb etc. as required and as per tender technical specifications & drawings. design and construction of foundation for exhaust pipe rack/ structure of dg set is included in the scope of the contractor.reference drg. nos. : i) ip1/119a/05034347/dwg/001/r0ii) ip1/119a/05044831/dwg/003/r0iii) ip1/119a/05044831/dwg/004/r0iv) ip1/119a/05044831/dwg/005/r0v) ip1/119a/05044831/dwg/006/r0, supply of sp

CTN :45591042

27 Jun, 2026 NA

Nainital - Uttarakhand

Tender For supply of sluice valve 200mm pn1 point 6 isi marked , sluice valve 150mm pn 1 point 6 isi marked , pump starter 12 point 5 hp delta isi marked , ht tape 3m 19mmx9mtr , ht tape 3m 25mm x 10mtr roll , non return valve 150mm isi marked , led garden light 10w , sluice valve 100mm pn 1 point 6 isi marked , led bulb 7 watts , cable copper pvc frlsh 2 point 5 sqmm multistranded single core , sluice valve 80mm pn 1 point 6 isi marked , sensor based led tube light batten 20w , heating element 1500 watt triangular type , non return valve 100mm isi marked , heating element 2000 watt triangular type , ht cable end box outdoor 3 c x 95 sqmm 11 kv e , led driver for 2 feet x 2feet false ceiling light fitting , ht cable end box indoor 3 c x 95 sqmm 11 kv e , heat strinks joint kit indoor 3c x 95 sqmm , cable copper frlsh pvc 1 point 5 sqmm multi stranded single core , submursible cu cable 16 sqmm x3core isi marked , submursible cu cable 25 sqmm x3core isi marked , sheet metal enclosure with plug top and mcb sp 20a , pvc flexible cable frlsh 0 point 5 sqm three core , pvc flexible cable 23 oblique 00076 twin core , led tube rod 20w essential 1200mm 2100 lm , thermostat for geyser 25 ltr , led electronic driver 150 w , led electronic driver 100 w , fan regulator switch type , mcb 63 amp 4 pole isolator , pvc flexible cable frlsh 1 point 5 sqm three core isi marked , mcb 40 amp 4 pole isolator , cable copper frlsh 1sqmm single core isi marked , mcb 32 amp 4 pole isolator , led electronic driver 45 w isi mrked , thermostat for geyser 50 ltr isi marked , 20amp plug and socket distribution board , modular socket with mcb sp 25a , regulator electronic for ceiling fan modular type , fan regulator dimmer 400 oblique 450w , switch socket combination 6a , led driver 90w , led electronic driver 72 w , mcb sp 06 amp 230 volts 10 ka , led tube light fitting 20 w alum extruded decorative box with driver and tubelight , led bulb 9 w 230 volt with electric backup battery , led tube light fitting 18 w alum extruded decorative box with driver and tubelight //bid details 2 / 136

CTN :45549158

09 Jul, 2026 NA

Kharagpur - West Bengal

Tender For distribution transformer of rating 500 kva, 11kv/415v-240v, 3-phase, 50hz, outdoor type, plinth mounted, on load type tap changer for variation of hv voltage from +5% to -15% in steps of 2.5%, energy efficiency level 3 or better, oil immersed, non-sealed type (transformer tank body and cover are bolted), copper wound, primary winding in delta and secondary winding in star (vector symbol- dyn11), onan cooled transformer, confirming to is 1180 (part 1): 2014 with amendment nos. 1,2,3,4 or latest, and supplied with all standard fittings mentioned in clause 20.1 of is 1180 (part 1) latest with condition that drain-cum-sampling valve will be applicable for all capacity of transformers. oil temperature indicator & winding temperature indicators will be provided as per clause 20.2 of is 1180 (part 1). terminal arrangement: the transformers shall be fitted on high voltage and low voltage sides with outdoor type bushings appropriate voltage and current ratings. the high voltage bushings (3 nos.) shall confirm to is/iec 60137. the low voltage bushings (4 nos.) shall confirm to is 7421. suitable cable-end box along with cable entry hole glands is tobe provided at l.t. side. following has to be submitted by supplier along with supply of material: (i) type test report of transformer having same rating, make (& model if any) and design from nabl accredited lab as per is 1180 (part 1) latest. (ii) routine test certificates as per is: 1180(part 1) latest. (iii) special test certificates as per clause 21.4 sl. no. (a), (c), (d), (e) of is: 1180 (part 1) latest. bee star rating:- 3 or above (firm shall submit a valid bee certificate for the offered product with desired bee star rating). [ warranty period: 30 months after the date of delivery ] ]

CTN :45479514

25 Jun, 2026 NA

Kharagpur - West Bengal

Tender For distribution transformer of rating 250 kva, 11kv/415v-240v, 3-phase, 50hz, outdoor type, plinth mounted, the type of tap changer: off-load tap changer for variation of hv voltage from +5% to -10% in steps of 2.5%, energy efficiency level 3 or better, oil immersed, non-sealed type (transformer tank body and cover are bolted), copper wound, primary winding in delta and secondary winding in star (vector symbol- dyn11), onan cooled transformer, conforming to is 1180 (part 1):2014 with amendment nos. 1,2,3,4 or latest, and supplied with all standard fittings mentioned in clause 20.1 of is 1180 (part 1) latest withcondition that drain-cum-sampling valve will be applicable for all capacity of transformers. oil temperature indicator & winding temperature indicators will be provided as per clause 20.2 f) of is 1180 (part 1). terminal arrangement: the transformers shall be fitted on high voltage and low voltage sides with outdoor type bushings of appropriate voltage and current ratings. the high voltage bushings (3 nos.) shall conform to is/iec 60137. the low voltage bushings (4 nos.) shall conform to is 7421. suitable cable-end box along with cable entry hole glands is to be provided at l.t. side. following has to be submitted by supplier along with supply of material: (i) type test report of transformer having same rating, make (& model if any) and design from nabl accredited lab as per is: 1180 (part 1) latest. (ii) routine test certificates as per is: 1180 (part 1) latest. (iii) special test certificates as per clause 21.4 sl. no. (a), (c), (d) & (e) of is: 1180 (part 1) latest. detailed specification attached as annexure a. [ warranty period: 30 months after the date of delivery ]]

CTN :45470987

29 Jun, 2026 NA

Jamshedpur - Jharkhand

Tender For supply & testing of 500 kva, 11kv/750v, 3-phase, 50 hz. outdoor type power transformer conforming to 15 2026 (part 1): 2011 (reaffirmed 2021), plinth mounted, copper wound, mineral oil immersed with freely breathing system (also called conservator system) as per clause 8.2 (a) of is 2026 (part 1), primary winding in delta and secondary winding in star (vector symbol-dyn11), onan cooled transformer, minimum short circuit impedance of 5% as per is 2026 (part 5), with all fittings specified in annexure a to this description, terminal arrangement: the transformers shall be fitted on high voltage and low voltage sides with outdoor type bushings of appropriate voltage and current ratings. the high voltage bushings (3 nos.) shall confirm to is/iec 60137. the low voltage bushings (4) nos.) shall conform to 15.7421. suitable cable-end box is to be provided as follows: a) for outdoor type: l.t. side tap changer: on-load tap changerfor variation of hv voltage from -+5% to -5% in steps of 1.25% make- andrew yule/aeg/crompton greaves/kirloskar electric co./abb/siemens/schneider or similar. [ warranty period: 30 months after the date of delivery ] ]

CTN :45117105

01 Jun, 2026 NA

Kharagpur - West Bengal

Tender For distribution transformer of rating 500 kva, 11kv/415v-240v, 3-phase, 50hz, outdoor type, plinth mounted, the type of tap changer for variation of hv voltage from +5% to -15% in steps of 2.5%, energy efficiency level 3 or better, oil immersed, non-sealed type (transformer tank body and cover are bolted), copper wound, primary winding in delta and secondary winding in star (vector symbol- dyn11), onan cooled transformer, confirming to is 1180 (part 1): 2014with amendment nos. 1,2,3,4 or latest, and supplied with all standard fittings mentioned in clause 20.1 of is 1180 (part 1) latest with condition that drain-cum-sampling valve will be applicable for all capacity of transformers. oil temperature indicator & winding temperature indicators will be provided as per clause 20.2 of is 1180 (part 1). terminal agreement: the transformers shall be fitted on high voltage and low voltage sides with outdoor type bushings appropriate voltage and current ratings. the high voltage bushings (3 nos.) shall confirm to is/iec 60137. the low voltage bushings (4 nos.) shall confirm to is 7421. suitable cable-end box along with cable entry hole glands is to beprovided at l.t. side. following has to be submitted by supplier along with supply of material: (i) type test report of transformer having same rating, make (& model if any) and design from nabl accredited lab as per is 1180 (part 1) latest. (ii) routine test certificates as per is: 1180(part 1) latest. (iii) special test certificates as per clause 21.4 sl. no. (a), (c), (d), (e) of is: 1180 (part 1) latest. [ warranty period: 30 months after the date of delivery ]

CTN :45143795

26 May, 2026 16.66 Lacs

Mydukur - Andhra Pradesh

Tender For provision towards purchase of necessary items (equipments) to government hospital in mydukur municipality. - supply, transportation and installation of desktop with fully loaded software as desired, with the following configuration. 1. processor: intel® core? i7-12th generation or higher version processor with intel® hd graphics 770 (2.9 ghz base frequency, up to 4.9 ghz with intel® turbo boost technology, 25 mb l3 cache, 12 cores 20 threads) intel q670 chipset 2. memory: 8 gb ddr4-3200 mhz sdram (1 x 8 gb) memory slots 2 dimm 3. hard drive 512gb ssd (hard drive 2 nd 1 tb 7200 sata hdd ) 4. 1 audio line in; 1 audio line out; 1 hdmi; 1 rj-45; 1 vga; 4 usb 3.0; 4 usb 2.0 5. operating systems: windows 11 pro professional 64 bit with product key license. 6. communications (intel wi-fi & blue tooth) 7. preloaded with latest version of antivirus symantec/ mcafee / nod32 / e-trust / avast internet security / kaspersky / quick heal / escan / msecure with following features: antivirus, antispyware, intrusion prevention browser protection with single management console with 3 year subscription with support updates and patches. 8. accessories: with required connecting cables and driver media should be supplied. 9. warranty: 3 year standard on-site comprehensive hardware warranty (including o.s support, spares- parts/service/labour/on-site) makes: hp prodesk or its equivalent in dell, supply, transportation and installation of all-in-one (print, copy, scan) with duplex, auto document feeder features: -print resolution 600 x 600dpi -print speed (a4) 27ppm -auto duplex printing standard -available paper size for auto duplex print a4, letter, legal (*1), indian legal, fulllscape -copy copy speed (a4) 27ppm maximum number of copies up to 999 copies scan type colour contact image sensor scan resolution optical up to 600 x 600dpi pull scan yes, usb and network makes: makes: canon imageclass mf244dw /hp/brother dcpb7535dw or its equivalen, supply installation testing and commissioning of dg set complete with 1500 rpm diesel engine of suitable bhp & ac brush less spdp alternator mounted on a common base frame & coupled through a flexible coupling or close coupled.alternator: it shall be self-regulated, self-excited and confirms to is: 13364/1992 or latest version with regulation of +5% from no load to full load, ip23, with standard alternator protection (over voltage, over speed& under voltage).diesel engine: it shall have residential silencer, up to 10 m exhaust piping, electronic / mechanical governor, manual & electric start, batteries, fuel tank & piping, control panel (16 g) with spn(for 5 kva)/tpn mccb of required rating (25/36/50 ka) with plc based engine controller supplied by oem, ammeter, voltmeter, frequency meter or multi-function meter, energy meter & hour meter, engine instruments panel, avm and automatic voltage regulator. the diesel engine shall be capable of providing 10% overload for 1 hr for every 11 hrs of continuous running at full load. the dg set shall be supplied with initial filling of fuel, lube oil, coolant oil as per oem specifications and shall be tested at site.acoustic enclosure: weatherproof, powder coated acoustic enclosure for dg set for sound attenuation fabricated from 1.6 mm crca sheet steel (structure) with side wall fabricated from 1.6 mm crca sheet and filled with foam as per cpcb norms latest amendments & is 8183. the doors are fabricated from 1.6 mm crca sheet packed with acoustic material, floor of ms chequered plate 5.0 mm thick, all doors/ opening are sealed with neoprene/ epdn gaskets.the dg set shall be maintained for two years after commissioning by the supplier including regular servicing,cost of consumables etc complete as specified by the oem along with warranty for two years.the enclosure has built in fuel tank, residential silencer (isolated from main dg chamber) with protection and tripping of dg set against temperature of more than 50 °c. all controls for opera

CTN :44964160

20 May, 2026 18.38 Lacs

Bhadradri Kothagudem - Telangana

Tender For corrigendum : roof bolts, m.s. bolts & nuts , rivets, washers & screws , , dog nails , , fish plates, nuts & bolts for fish plates , , belt jointing pins , , cable hooks and signal hooks , , belt conveyor rollers , , belt sections , , resin capsules , , cement capsules , , gi canisters , , blasting gallery - spacers , , radiator repairs , , repairs and rewinding of motors of ac & dc , , repairs / rewinding of transformers (welding/lighting/power) , , gl wire , , wire mesh for longwall salvage , , manufacturing of supply of electrical coils for , , i) ac motors up to 6.6kv grade , , li) transformer coils up to 33 kv grade , , repairs of rotors for electric motor , , lighting cable , , steel chock manufacturing , , house wiring , , all types of fan repairs , , shovel bucket welding , , repairs of pumps , , couplings manufacturing , , special steel and alloy castings , , (tooth points, track pads, mn steel casting) , , manufacturing of fly ash bricks (not to be manufactured at stores site. it shall be at their own site) , , manufacturing of pump components (spares) , , transformer oil filtration , , reconditioning of drill bits an drill rods. , , vulcanizing the old training cable sof drill machines, sdls, lhds etc (work should be carried out at the respective mine premises. , , manufacturing of earth clamps, g.i.flats, g.i.bolts and nuts. , , crimping of hydraulic hoses. , , repairs to hydraulic pumps, motors, control valves and other related components. , , refurbishing of lt & ht switches with oem spares including testing. , , manufacturing/repairs of slip rings & d-contacts. , , furniture repairs i.e. cane chairs, tables, almirahs etc. , , repairs to wet grinders, water purifiers and water coolers , , manufacturing of coupling bolts of all sizes , , fabrication of oht line components like cross arms, clamps, stay wires, cross brassings, base plates etc. , , manufacturing of haulage rope drum rollers. , , all sizes of ventilation doors. , , safety boards designing/stickering/painting with retro-reflective radium papers/paint on hemm/ radium stickering in underground & surface, radium boards, safety boards & radium jackets. , , fabrication of lighting & cable cross over towers , , maintenance & repairs of air conditioners on hemm , , painting work in underground and on surface , , fabrication and erection of ms structural works like gantry, bunker etc. , , tailoring works at hospitals & area workshops , , manufacturing of hume pipes , , clay pills manufacturing , , maintenance of pmts/lighting transformers/power transformers & sub-stations , , erection /renovation of residential/pmts/sb-station earth pits (conventional type /chemical type). , , testing of all protective relays & mprs , , tub assembling/repairing of coal tubs in mines. , , cl casting works like ci pulley, tub wheels , , outsourcing works in mines, like masonary walls construction, surface material loading, cleaning and dusting in underground etc. , , all types of computer software installation, antivirus, hardware and network installation. , , cc cameras installation and repairs.

CTN :44948129

20 May, 2026 NA

Jamshedpur - Jharkhand

Tender For supply & testing of 500 kva, 11kv/750v, 3-phase, 50 hz. outdoor type power transformer conforming to 15 2026 (part 1): 2011 (reaffirmed 2021), plinth mounted, copper wound, mineral oil immersed with freely breathing system (also called conservator system) as per clause 8.2 (a) of is 2026 (part 1), primary winding in delta and secondary winding in star (vector symbol-dyn11), onan cooled transformer, minimum short circuit impedance of 5% as per is 2026 (part 5), with all fittings specified in annexure a to this description, terminal arrangement: the transformers shall be fitted on high voltage and low voltage sides with outdoor type bushings of appropriate voltage and current ratings. the high voltage bushings (3 nos.) shall confirm to is/iec 60137. the low voltage bushings (4) nos.) shall conform to 15.7421. suitable cable-end box is to be provided as follows: a) for outdoor type: l.t. side tap changer: on-load tap changerfor variation of hv voltage from -+5% to -5% in steps of 1.25% make- andrew yule/aeg/crompton greaves/kirloskar electric co./abb/siemens/schneider or similar. [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :44925409

08 May, 2026 NA

Gandhinagar - Gujarat

Tender For supply of wired vocal microphone , general instrument microphone , gooseneck podium microphone , handheld wireless microphone , wireless headworn microphone , wireless lavalier microphone , 32 channel digital mixture with stage rack , digital stage box , headphones , digital signal processor , touch panel controller -tpc-1 , front of the house -foh array speakers left and right , array subwoofer , grid or array coupling kit for array speakers , suspension kit for array speakers or subwoofers , amplifiers for foh array and subwoofers , powered stage monitor speakers , front fills , green room and control room , amplifiers for green room and control room speakers , microphone stand large , microphone stand small , network switch , microphone cable , speaker cable , equipment rack , conduit pipe , cable tray , implementation and testing

Cable End Box Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector